Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Reciprocating Pumps

Civil Engineering · Hydraulics & Fluid Mechanics

43 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

A reciprocating pump is generally less suitable than a centrifugal pump for handling

  1. viscous oils that cannot pass through the suction valve
  2. liquids with suspended solids that damage the valves
  3. clean water at high head that overloads the piston
  4. hot water that cannot lift the delivery valves
Show answer & solution

Answer: (B) liquids with suspended solids that damage the valves

Solids lodge under the valve seats and score the piston and cylinder, whereas centrifugal pumps with open passages tolerate them better.

Question 2

The theoretical discharge of a reciprocating pump is fixed by its

  1. delivery head and the friction head
  2. piston area, stroke length and speed
  3. delivery valve size and its spring stiffness
  4. suction pipe diameter, length and static lift
Show answer & solution

Answer: (B) piston area, stroke length and speed

Theoretical discharge is swept volume per unit time = A L N/60 (times 2 if double-acting); slip then reduces the actual discharge.

Question 3

The indicator diagram of a reciprocating pump is a graphical plot of the

  1. piston velocity against crank angle over a full revolution
  2. power input to the shaft against the discharge delivered
  3. pressure head in the cylinder against piston displacement
  4. discharge delivered by the pump against time over the cycle
Show answer & solution

Answer: (C) pressure head in the cylinder against piston displacement

The indicator diagram plots cylinder pressure head against piston stroke through one cycle.

Question 4

A reciprocating pump is suitable for:

  1. Slurries with high sediment load
  2. Open channel irrigation
  3. Less discharge and higher heads
  4. High discharge and low head
Show answer & solution

Answer: (C) Less discharge and higher heads

Reciprocating pumps deliver small discharge at high heads.

Question 5

An air vessel fitted near the suction and/or delivery end of a reciprocating pump serves mainly to

  1. raise the delivery head by compressing air above atmospheric
  2. cushion the flow pulsations and smooth the pipeline flow
  3. increase the discharge by storing extra liquid permanently
  4. trap solid particles before they can reach the valves
Show answer & solution

Answer: (B) cushion the flow pulsations and smooth the pipeline flow

The air in the vessel compresses and expands, absorbing the intermittent flow of the piston and smoothing the flow in the pipe.

Question 6

Which pump type is suitable for small discharge and high heads?

  1. Centrifugal pump
  2. Axial flow pump
  3. Mixed flow pump
  4. Reciprocating pump
Show answer & solution

Answer: (D) Reciprocating pump

Reciprocating pumps are positive displacement machines suited to small discharge and high head.

Question 7

A reciprocating pump is also called a ……………….. displacement pump.

  1. Negative
  2. Kinetic
  3. Positive
  4. Dynamic
Show answer & solution

Answer: (C) Positive

Reciprocating pumps trap and displace fixed volumes, so they are positive displacement pumps.

Question 8

Slip of a reciprocating pump can be negative when:

  1. The suction pipe is long, the delivery pipe is short and the pump runs at high speed
  2. The suction pipe is short, the delivery pipe is long and the pump runs at high speed
  3. The pump runs at very low speed with leaking valves
  4. Air vessels are removed from both pipes
Show answer & solution

Answer: (A) The suction pipe is long, the delivery pipe is short and the pump runs at high speed

Negative slip occurs when the long suction pipe's inertia keeps the delivery valve open late (short delivery pipe, high speed), so actual discharge exceeds theoretical.

Question 9

For a single-acting reciprocating pump with piston area A, stroke length L and speed N rpm, the theoretical discharge is

  1. Q = 2ALN/60
  2. Q = AN/(60L)
  3. Q = ALN/60
  4. Q = AL/(60N)
Show answer & solution

Answer: (C) Q = ALN/60

Volume per stroke is AL, delivered once per revolution, giving N/60 deliveries per second: Q = ALN/60.

Question 10

A hydraulic lift, used for raising loads (such as in some elevator systems), typically works using a

  1. reciprocating pump that lifts the load directly, with no ram fitted
  2. large ram in a cylinder, driven by pressurised hydraulic fluid
  3. chain and counterweight system driven by a water wheel
  4. rotating impeller that raises the car by centrifugal action
Show answer & solution

Answer: (B) large ram in a cylinder, driven by pressurised hydraulic fluid

In a hydraulic lift, fluid pressure acts on a ram in a cylinder that raises the car directly or through a sheave.

Question 11

A reciprocating pump is a positive-displacement pump that operates using a

  1. pair of meshing gears trapping liquid between teeth
  2. rotating impeller throwing the liquid outward
  3. jet of water striking curved vanes on a wheel
  4. piston or plunger moving to and fro in a cylinder
Show answer & solution

Answer: (D) piston or plunger moving to and fro in a cylinder

A reciprocating pump is positive-displacement: each stroke of the piston or plunger displaces a fixed volume of liquid.

Question 12

Air vessels in reciprocating pumps are used to:

  1. Prevent cavitation in centrifugal impellers
  2. Double delivery pressure
  3. Increase suction lift limit
  4. Smooth out flow and reduce acceleration head losses
Show answer & solution

Answer: (D) Smooth out flow and reduce acceleration head losses

Air vessels smooth the flow and reduce friction and acceleration heads in the pipes.

Question 13

The discharge of a double-acting reciprocating pump is given by:

  1. LAN
  2. 2LAN / 60
  3. 4LAN / 60
  4. LAN / 60
Show answer & solution

Answer: (B) 2LAN / 60

For a double-acting pump, Q = 2LAN/60 (L stroke, A piston area, N rpm).

Question 14

Which pump is successfully used for lifting water directly into high-pressure boilers?

  1. Reciprocating feed pump
  2. Open impeller centrifugal drainage pump
  3. Low-head axial flow pump
  4. Air-lift pump
Show answer & solution

Answer: (A) Reciprocating feed pump

High pressure and small discharge for boiler feed is best met by reciprocating pumps.

Question 15

Suction and delivery valves in a reciprocating pump are typically

  1. rotary valves driven from the crankshaft by gearing
  2. spring-loaded relief valves that open only on overpressure
  3. automatic non-return valves opened by pressure differences
  4. cam-operated valves opening at preset crank angle positions
Show answer & solution

Answer: (C) automatic non-return valves opened by pressure differences

Suction and delivery valves are check valves that lift and seat automatically with the pressure changes caused by the piston.

Question 16

The hydraulic action of a centrifugal pump is best described as:

  1. Gravity-assisted siphon flow
  2. A positive displacement reciprocating cycle
  3. A direct impulse jet mechanism
  4. The exact reverse operation of a reaction turbine
Show answer & solution

Answer: (D) The exact reverse operation of a reaction turbine

A centrifugal pump works like a reaction turbine run in reverse.

Question 17

Which of the following is NOT a reciprocating pump?

  1. Diaphragm pump
  2. Piston pump
  3. Rotary gear pump
  4. Plunger pump
Show answer & solution

Answer: (C) Rotary gear pump

Plunger, piston and diaphragm pumps work by reciprocating motion; a gear pump is rotary.

Question 18

The area of the (ideal, frictionless) indicator diagram of a reciprocating pump is proportional to the

  1. friction power lost in the delivery pipe
  2. mean piston speed over the cycle
  3. slip loss of the pump per stroke
  4. work done by the pump per stroke
Show answer & solution

Answer: (D) work done by the pump per stroke

Area = pressure head × stroke volume, which is proportional to the work done per stroke.

Question 19

A specific speed of 160 to 500 r.p.m. for a centrifugal pump indicates:

  1. High speed pump with axial flow
  2. Low discharge booster pump
  3. Slow speed radial flow pump
  4. Positive displacement reciprocating unit
Show answer & solution

Answer: (A) High speed pump with axial flow

Ns 160 to 500 r.p.m. is the range of high speed axial flow pumps.

Question 20

The saving in work done by fitting an air vessel to a double-acting reciprocating pump is:

  1. 39.2%
  2. 48.8%
  3. 84.8%
  4. 88.4%
Show answer & solution

Answer: (A) 39.2%

For a double-acting pump the air vessel saves about 39.2% of the work done against friction.

Question 21

In a reciprocating pump, air vessels are fitted to:

  1. Suction and delivery pipes close to the cylinder
  2. Discharge outlet only
  3. Crankcase lubrication sump
  4. Prime mover housing
Show answer & solution

Answer: (A) Suction and delivery pipes close to the cylinder

Air vessels are fitted on suction and delivery pipes as close to the cylinder as possible.

Question 22

Negative slip in a reciprocating pump means the actual discharge

  1. exceeds the theoretical discharge, due to pipe inertia at high speed
  2. flows backward through the delivery valve during every suction stroke
  3. is less than the theoretical discharge, due to leakage past the valves
  4. equals the theoretical discharge, since the valves close instantly
Show answer & solution

Answer: (A) exceeds the theoretical discharge, due to pipe inertia at high speed

When actual discharge exceeds theoretical discharge the slip (Qth - Qact) is negative, which can occur through inertia effects at high speed.

Question 23

Which of the following statements about centrifugal pumps, compared with reciprocating pumps, is correct?

  1. They are best suited to very high heads with small discharge
  2. They suit large discharges at moderate heads and need less floor area
  3. They deliver a pulsating flow that needs air vessels
  4. They are self-priming and need no priming before starting
Show answer & solution

Answer: (B) They suit large discharges at moderate heads and need less floor area

Centrifugal pumps give uniform flow, large discharge at low to medium head and are compact.

Question 24

Without an air vessel, the acceleration head modifies the ideal indicator diagram by

  1. keeping the lines horizontal but shifting the diagram up by a constant head
  2. sloping the suction and delivery lines as the head varies in the stroke
  3. leaving the diagram unchanged, as the accelerating effects cancel out
  4. shrinking the diagram to a single point at the mean pressure
Show answer & solution

Answer: (B) sloping the suction and delivery lines as the head varies in the stroke

Acceleration head varies with piston position (largest at stroke ends), so the flat suction and delivery lines of the ideal diagram become inclined.

Question 25

A jet pump (or ejector) operates by using a high-velocity jet of a primary (motive) fluid to

  1. displace a piston which then drives the second fluid
  2. entrain a secondary fluid by momentum transfer
  3. spin an impeller that flings the secondary fluid outward
  4. compress the secondary fluid in a closed cylinder
Show answer & solution

Answer: (B) entrain a secondary fluid by momentum transfer

The high-velocity jet creates low pressure and drags the secondary fluid along with it by momentum exchange.

Question 26

Which pump is commonly used for lifting water from deep bore wells?

  1. Gravitational water wheel
  2. Submersible (deep-well turbine) pump
  3. Surface reciprocating pump
  4. Low-lift volute centrifugal pump
Show answer & solution

Answer: (B) Submersible (deep-well turbine) pump

Submersible or deep-well turbine pumps are placed inside the bore well, avoiding the suction lift limit.

Question 27

Compared with a centrifugal pump, a reciprocating pump is generally better suited to

  1. small-head duties needing little maintenance and a simple build
  2. pumping slurries with abrasive solids, with less valve wear
  3. high discharge and low head duties, with a smoother flow
  4. high head, low discharge duties, though with pulsating flow
Show answer & solution

Answer: (D) high head, low discharge duties, though with pulsating flow

Positive displacement gives high pressure at small discharge, but the delivery is pulsating unless an air vessel is fitted.

Question 28

The choice between a centrifugal pump and a reciprocating pump mainly depends on

  1. motor rating and foundation size, regardless of the liquid handled
  2. floor space and pipe diameter, regardless of head and discharge
  3. maintenance interval and spare-part price, regardless of head or liquid
  4. head, discharge, liquid nature (solids, viscosity) and flow smoothness
Show answer & solution

Answer: (D) head, discharge, liquid nature (solids, viscosity) and flow smoothness

The duty (head and discharge), liquid properties and acceptable pulsation decide which pump type is appropriate.

Question 29

A gear pump is a type of

  1. reciprocating pump moving the liquid with a gear-driven piston
  2. impulse turbine driven by a water jet on gear-shaped buckets
  3. rotary positive-displacement pump trapping liquid between gear teeth
  4. centrifugal pump throwing liquid outward with gear-driven vanes
Show answer & solution

Answer: (C) rotary positive-displacement pump trapping liquid between gear teeth

Liquid trapped in the tooth spaces is carried round the casing wall from suction to delivery, which is positive-displacement action.

Question 30

A centrifugal pump works on the principle that

  1. liquid is lifted by the pressure wave from sudden valve closure
  2. mechanical energy becomes pressure and kinetic energy via impeller action
  3. a fixed volume of liquid is displaced by a piston during each stroke
  4. hydraulic energy is converted to shaft work by a jet striking buckets
Show answer & solution

Answer: (B) mechanical energy becomes pressure and kinetic energy via impeller action

The rotating impeller flings liquid outward, raising its pressure and velocity at the expense of shaft work.

Question 31

The theoretical power required to drive a reciprocating pump (w = specific weight, Q = discharge, Hs = suction head, Hd = delivery head) is:

  1. w Q (Hs - Hd)
  2. w Q Hs
  3. w Q Hd
  4. w Q (Hs + Hd)
Show answer & solution

Answer: (D) w Q (Hs + Hd)

Pump must lift water through the total static head Hs + Hd, so P = wQ(Hs + Hd).

Question 32

The type of centrifugal pump preferred for a very low specific speed of 20 r.p.m. is:

  1. High speed pump with axial flow
  2. Mixed flow pump with high specific speed
  3. Medium speed pump with radial flow at outlet
  4. Slow speed pump with radial flow at outlet
Show answer & solution

Answer: (D) Slow speed pump with radial flow at outlet

Low Ns (about 10 to 30) corresponds to slow-speed, radial-flow impellers.

Question 33

Slip in a reciprocating pump is defined as the

  1. shortfall of actual discharge below theoretical, as a fraction of theoretical
  2. shortfall of actual discharge below theoretical, as a fraction of actual
  3. ratio of the actual discharge to the theoretical discharge
  4. difference between the suction and the delivery stroke volumes of the piston
Show answer & solution

Answer: (A) shortfall of actual discharge below theoretical, as a fraction of theoretical

Slip = (Qth - Qact)/Qth, the fractional shortfall mainly caused by leakage and delayed valve closure.

Question 34

The maximum speed of a reciprocating pump without flow separation in the suction pipe is limited mainly by

  1. the maximum delivery pressure the cylinder wall can withstand
  2. keeping the suction pipe pressure above vapour pressure at stroke end
  3. the strength of the crank and connecting rod under inertia loads
  4. the stiffness and lift of the delivery valve spring and seat
Show answer & solution

Answer: (B) keeping the suction pipe pressure above vapour pressure at stroke end

At the end of the suction stroke the acceleration head is greatest, and if static, friction and acceleration heads drive pressure to vapour pressure the column separates.

Question 35

By fitting an air vessel to a single-acting reciprocating pump, the percentage saving in work done against friction is:

  1. 39.2%
  2. 48.8%
  3. 84.8%
  4. 88.4%
Show answer & solution

Answer: (C) 84.8%

For a single-acting pump the air vessel saves about 84.8% of the work done against friction.

Question 36

A single-acting reciprocating pump delivers liquid

  1. during both the forward and return strokes of the piston
  2. only during one stroke of the piston in each cycle
  3. continuously, with the two strokes overlapping each cycle
  4. twice per cycle, once on each face of the piston head
Show answer & solution

Answer: (B) only during one stroke of the piston in each cycle

Only one side of the piston works on liquid, so delivery occurs once per crank revolution.

Question 37

Slip of a reciprocating pump is defined as:

  1. Ratio of actual discharge to theoretical discharge
  2. Product of volumetric and mechanical efficiency
  3. Difference between theoretical discharge and actual discharge
  4. Sum of actual and theoretical discharge
Show answer & solution

Answer: (C) Difference between theoretical discharge and actual discharge

Slip = theoretical discharge - actual discharge.

Question 38

Acceleration head in a reciprocating pump refers to the additional head required to

  1. accelerate the liquid column as piston velocity changes
  2. open the suction and delivery valves against their springs
  3. overcome the friction between the liquid and the pipe wall
  4. lift the liquid through the static suction and delivery heads
Show answer & solution

Answer: (A) accelerate the liquid column as piston velocity changes

The piston speed varies, so the liquid column must be accelerated and decelerated, requiring an extra head ha = (L/g)(A/a) ω² r cos θ.

Question 39

Percentage slip of a reciprocating pump is related to its coefficient of discharge (Cd) by the expression

  1. (1 - Cd) × 100
  2. (1 + Cd) × 100
  3. (1/Cd - 1) × 100
  4. Cd × 100
Show answer & solution

Answer: (A) (1 - Cd) × 100

Slip = (Qth - Qact)/Qth = 1 - Cd, so percentage slip = (1 - Cd) × 100.

Question 40

Which pump is preferred for flood control and high-volume low-head irrigation applications?

  1. Screw displacement pump
  2. High-head reciprocating pump
  3. Hydraulic ram
  4. Axial flow pump (propeller pump)
Show answer & solution

Answer: (D) Axial flow pump (propeller pump)

Axial flow (propeller) pumps give very large discharge at low head, ideal for flood control and irrigation.

Question 41

The coefficient of discharge of a reciprocating pump is defined as the ratio of the

  1. slip loss to the actual delivered discharge
  2. slip loss to the theoretical discharge
  3. actual discharge to the theoretical discharge
  4. theoretical discharge to the actual discharge
Show answer & solution

Answer: (C) actual discharge to the theoretical discharge

Cd = Qact/Qth, normally slightly less than 1.

Question 42

The air vessel in a reciprocating pump is:

  1. A motorized pressure booster compressor
  2. A cast iron closed chamber having an opening at its base to cushion flow pulsations
  3. An exhaust safety valve
  4. A vacuum priming tank
Show answer & solution

Answer: (B) A cast iron closed chamber having an opening at its base to cushion flow pulsations

An air vessel is a closed chamber, with an opening at its base, that absorbs flow fluctuations.

Question 43

Friction head in the suction or delivery pipe of a reciprocating pump varies approximately with the

  1. cube of the instantaneous liquid velocity in the pipe
  2. square of the instantaneous liquid velocity in the pipe
  3. piston displacement measured from the start of the stroke
  4. instantaneous acceleration of the piston in the stroke
Show answer & solution

Answer: (B) square of the instantaneous liquid velocity in the pipe

Pipe friction head hf = 4fLv²/(2gd) is proportional to v², and v follows the piston velocity.

Practice these 43 questions interactively →