Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Flow Measurement

Civil Engineering · Hydraulics & Fluid Mechanics

40 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

A jet from a small orifice at a depth of 2.0 m below the water surface of a tank strikes the ground 1.9 m horizontally from the vena contracta, after falling 0.5 m vertically. The coefficient of velocity of the orifice is

  1. 0.47
  2. 0.95
  3. 1.90
  4. 3.80
Show answer & solution

Answer: (B) 0.95

Cv = x/(2√(yH)) = 1.9/(2√(0.5×2.0)) = 0.95.

Question 2

Compared with a venturimeter of equal throat size, a flow nozzle is

  1. costlier and longer but has a smaller head loss
  2. cheaper and shorter but has a larger permanent head loss
  3. equal in cost, since both have a diverging cone
  4. unsuitable for high-velocity flow, since it has no divergent part
Show answer & solution

Answer: (B) cheaper and shorter but has a larger permanent head loss

A flow nozzle has no diffuser, so it is compact and cheap but gives higher permanent loss than a venturimeter (still less than an orifice plate).

Question 3

A Borda's mouthpiece of diameter 60 mm discharges water running free under a constant head of 2 m. The discharge is approximately

  1. 8.86 L/s
  2. 10.98 L/s
  3. 12.52 L/s
  4. 15.14 L/s
Show answer & solution

Answer: (A) 8.86 L/s

Cd = 0.5 for a free-running Borda's mouthpiece; Q = 0.5 × 2.827×10⁻³ × √(2×9.81×2) ≈ 8.86 L/s.

Question 4

A venturimeter with a U-tube differential manometer connected between inlet and throat is installed first horizontally and then on a vertical pipe, with the same discharge. The manometer deflection will be

  1. larger, because elevation head is added to the reading
  2. smaller, because gravity assists the flow
  3. the same, since it responds to the piezometric head difference
  4. zero, because the sections are at different levels
Show answer & solution

Answer: (C) the same, since it responds to the piezometric head difference

Discharge depends on the piezometric head difference (p/γ + z), which is what the differential manometer measures, so the reading is independent of inclination.

Question 5

Water in a tank stands 2 m over a small orifice in the side wall. The orifice is 3 m over level ground. Taking Cv = 1, the horizontal distance from the orifice at which the jet strikes the ground is

  1. 4.90 m
  2. 5.00 m
  3. 7.75 m
  4. 12.00 m
Show answer & solution

Answer: (A) 4.90 m

x = 2√(yH) = 2√(3×2) ≈ 4.90 m.

Question 6

An external cylindrical mouthpiece of diameter 40 mm runs full under a constant head of 5 m of water. Taking Cd = 0.855, the discharge is approximately

  1. 6.22 L/s
  2. 7.52 L/s
  3. 7.72 L/s
  4. 10.64 L/s
Show answer & solution

Answer: (D) 10.64 L/s

Q = Cd·a·√(2gH) = 0.855 × 1.2566×10⁻³ × √(2×9.81×5) ≈ 10.64 L/s.

Question 7

A prismatic tank is emptied through a bottom orifice. Compared with the time needed to discharge the same volume under a constant head equal to the initial head, the time of emptying is

  1. equal to it
  2. half as long
  3. twice as long
  4. four times as long
Show answer & solution

Answer: (C) twice as long

Constant head: t = AH/(Cd·a√(2gH)); emptying: t = 2AH/(Cd·a√(2gH)), which is twice as long.

Question 8

The coefficient of discharge of an orifice meter is much lower than that of a venturimeter chiefly because

  1. the jet contracts and eddy losses are large
  2. the area of the orifice is larger than the pipe area
  3. the velocity at the plate is lower than in the pipe
  4. the fluid sticks to the thin plate more strongly
Show answer & solution

Answer: (A) the jet contracts and eddy losses are large

A sharp plate causes strong jet contraction and eddying downstream, giving Cd of about 0.6 compared with about 0.98 for a venturimeter.

Question 9

A large rectangular orifice 0.4 m wide has its top edge 0.5 m and its bottom edge 1.5 m below the free surface. Taking Cd = 0.6, the discharge is approximately

  1. 709 L/s
  2. 1051 L/s
  3. 1063 L/s
  4. 1302 L/s
Show answer & solution

Answer: (B) 1051 L/s

Q = (2/3)·Cd·b·√(2g)·(H2^1.5 − H1^1.5) = 0.6667×0.6×0.4×4.429×(1.837 − 0.354) ≈ 1051 L/s.

Question 10

An external cylindrical mouthpiece runs full under a head of 5 m of water. If atmospheric pressure head is 10.3 m of water, the absolute pressure head at the vena contracta (taking 0.89H as the vacuum head) is

  1. 4.45 m
  2. 5.30 m
  3. 5.85 m
  4. 14.75 m
Show answer & solution

Answer: (C) 5.85 m

Absolute head at vena contracta = Ha − 0.89H = 10.3 − 0.89×5 = 5.85 m of water.

Question 11

In an orifice meter, to double the discharge the pressure head difference across the meter must be

  1. increased to 1.41 times
  2. doubled
  3. increased to 4 times
  4. increased to 8 times
Show answer & solution

Answer: (C) increased to 4 times

Q ∝ √h, so doubling Q requires h to become 2² = 4 times.

Question 12

A horizontal venturimeter has an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure head difference between inlet and throat is 2.0 m of water and Cd = 0.98. The discharge is approximately

  1. 105.2 L/s
  2. 108.5 L/s
  3. 112.0 L/s
  4. 114.3 L/s
Show answer & solution

Answer: (C) 112.0 L/s

Q = Cd·A1A2√(2gh)/√(A1²−A2²) = 0.98 × 0.01825 × √(2×9.81×2.0) ≈ 112.0 L/s.

Question 13

For a completely submerged orifice discharging into a second tank, the effective head causing flow is

  1. the difference of water levels on the two sides
  2. the depth of the orifice below the upstream surface
  3. the depth of the orifice below the downstream surface
  4. the sum of the depths on the two sides
Show answer & solution

Answer: (A) the difference of water levels on the two sides

Q = Cd·a·√(2g(H1 − H2)), where H1 − H2 is the difference between the upstream and downstream water levels.

Question 14

A venturimeter carries oil of relative density 0.8. A mercury (relative density 13.6) differential manometer connected between inlet and throat shows a deflection of 150 mm. The pressure head difference in metres of oil is

  1. 1.89 m
  2. 1.92 m
  3. 2.04 m
  4. 2.40 m
Show answer & solution

Answer: (D) 2.40 m

Δh = x(Sm/So − 1) = 0.15×(13.6/0.8 − 1) = 0.15×16 = 2.40 m of oil.

Question 15

Cavitation in a venturimeter is most likely to begin

  1. at the inlet section, where the velocity is lowest
  2. in the divergent cone near the outlet
  3. in the connecting tubes of the manometer
  4. at the throat, where the pressure is lowest
Show answer & solution

Answer: (D) at the throat, where the pressure is lowest

Velocity is highest at the throat, so pressure is lowest there and may fall to vapour pressure.

Question 16

The divergent cone of a venturimeter is made long with a small included angle (about 5° to 7°) mainly to

  1. increase the velocity at the throat further
  2. avoid flow separation and keep the head loss small
  3. raise the coefficient of contraction
  4. allow the pressure to exceed its inlet value
Show answer & solution

Answer: (B) avoid flow separation and keep the head loss small

A gentle divergence prevents boundary-layer separation and eddy losses, so most of the kinetic head is recovered as pressure.

Question 17

For a sharp-edged circular orifice discharging water into the atmosphere, a typical value of the coefficient of contraction is

  1. 0.50 to 0.52
  2. 0.62 to 0.64
  3. 0.80 to 0.85
  4. 0.95 to 0.99
Show answer & solution

Answer: (B) 0.62 to 0.64

The jet contracts to about 62–64% of the orifice area at the vena contracta, so Cc ≈ 0.62–0.64.

Question 18

The coefficient of contraction of a free-running Borda's (re-entrant) mouthpiece is 0.5. This value follows from applying

  1. the continuity equation alone to the jet
  2. the hydrostatic law along the jet axis
  3. the energy equation with only an exit loss
  4. the momentum equation together with Bernoulli's equation
Show answer & solution

Answer: (D) the momentum equation together with Bernoulli's equation

Equating the net hydrostatic force on the mouthpiece to the rate of momentum change and combining with Bernoulli gives a_c/a = 1/2.

Question 19

Water stands 4 m deep in a tank on level ground. A small orifice is to be placed on the side wall so that the horizontal range of the jet on the ground is maximum. The orifice height from the ground should be

  1. 1 m
  2. 2 m
  3. 3 m
  4. 4 m
Show answer & solution

Answer: (B) 2 m

Range x = 2√(yH) with y + H = 4 m is largest when y = H = 2 m, giving the orifice at mid-depth.

Question 20

The coefficient of velocity of an orifice is slightly less than unity mainly because of

  1. the contraction of the jet at the vena contracta
  2. viscous friction and energy loss near the orifice
  3. the compressibility of water
  4. the weight of the air over the free surface
Show answer & solution

Answer: (B) viscous friction and energy loss near the orifice

Cv = actual velocity / theoretical velocity; friction and eddy losses reduce the actual velocity (Cv ≈ 0.97–0.99). Contraction affects Cc, not Cv.

Question 21

A pitot tube placed on the axis of a pipe carrying fully developed laminar flow reads the maximum velocity. The mean velocity in the pipe is then equal to

  1. 0.50 times the reading
  2. 0.67 times the reading
  3. 0.82 times the reading
  4. 0.95 times the reading
Show answer & solution

Answer: (A) 0.50 times the reading

For laminar flow the velocity profile is parabolic, so Vmean = 0.5 Vmax (the 0.82 ratio applies roughly to turbulent flow).

Question 22

If the head over an external cylindrical mouthpiece becomes very large, the pressure at the vena contracta falls so low that the

  1. discharge coefficient exceeds unity
  2. jet springs clear of the wall and flow no longer runs full
  3. flow becomes laminar inside the tube
  4. pressure there exceeds the atmospheric value
Show answer & solution

Answer: (B) jet springs clear of the wall and flow no longer runs full

The vacuum at the vena contracta grows with head (about 0.89H); once it approaches vapour pressure, the jet springs clear and the full-bore flow breaks down.

Question 23

For the same tank and orifice (area 4 m², orifice 50 mm, Cd = 0.6), the time taken for the water level to fall from 4 m to 1 m over the orifice is approximately

  1. 1454 s
  2. 1533 s
  3. 3066 s
  4. 4336 s
Show answer & solution

Answer: (B) 1533 s

t = 2A(√H1 − √H2)/(Cd·a·√(2g)) = 2×4×(2 − 1)/(0.6×1.9635×10⁻³×4.429) ≈ 1533 s.

Question 24

Neglecting air resistance, a jet leaving horizontally from a small orifice in the side wall of a tank follows

  1. a circular arc
  2. a straight line sloping downward
  3. a catenary curve
  4. a parabolic path
Show answer & solution

Answer: (D) a parabolic path

Horizontal velocity is constant while vertical motion is uniformly accelerated, giving y = gx²/(2v²), a parabola.

Question 25

Rating of a current meter means

  1. adjusting the instrument to read zero in still water
  2. converting stage readings to discharge using a weir
  3. relating rotor speed to water velocity by towing it in still water
  4. calibrating a depth sounder against a staff gauge
Show answer & solution

Answer: (C) relating rotor speed to water velocity by towing it in still water

Rating towing at known speeds in still water gives the calibration equation v = aN + b used in the field.

Question 26

A flow nozzle of throat diameter 75 mm is installed in a 150 mm pipe carrying water. The pressure difference across the nozzle is 40 kPa and Cd = 0.96. The discharge is approximately

  1. 37.9 L/s
  2. 39.2 L/s
  3. 43.8 L/s
  4. 53.6 L/s
Show answer & solution

Answer: (B) 39.2 L/s

Q = Cd·a_n·√(2Δp/ρ)/√(1−β⁴) = 0.96 × 4.418×10⁻³ × √(80) / √(1 − 0.0625) ≈ 39.2 L/s.

Question 27

An orifice meter with a 100 mm orifice is fitted in a 200 mm pipe carrying water. The mercury manometer (relative density 13.6) connected across the meter shows a deflection of 250 mm. With Cd = 0.62, the discharge is approximately

  1. 39.5 L/s
  2. 41.1 L/s
  3. 44.2 L/s
  4. 63.8 L/s
Show answer & solution

Answer: (A) 39.5 L/s

h = 0.25×(13.6−1) = 3.15 m; Q = Cd·a0√(2gh)/√(1−(a0/A)²) = 0.62 × 0.007854 × 7.861 / 0.9682 ≈ 39.5 L/s.

Question 28

Water flows at 0.12 m³/s through a horizontal venturimeter with inlet diameter 300 mm and throat diameter 150 mm. If the inlet pressure is 200 kPa, the throat pressure (ideal flow, no losses) is approximately

  1. 156.8 kPa
  2. 175.5 kPa
  3. 176.9 kPa
  4. 178.4 kPa
Show answer & solution

Answer: (D) 178.4 kPa

v1 = 1.70 m/s, v2 = 6.79 m/s; p2 = p1 − ½ρ(v2² − v1²) = 200 − 0.5×(46.11 − 2.88) ≈ 178.4 kPa.

Question 29

A rotameter measures flow rate on the principle that

  1. a paddle wheel turns at a speed proportional to flow rate
  2. the pressure drop across a fixed throat varies as the square of flow
  3. the travel time of a tracer between two points is recorded
  4. a float rises in a tapered tube until drag balances its weight
Show answer & solution

Answer: (D) a float rises in a tapered tube until drag balances its weight

A rotameter is a variable-area, constant-pressure-drop meter: the float height is a direct measure of the flow.

Question 30

In a pitot-static tube, the static pressure holes are drilled on the side of the outer tube some distance behind the nose so that they

  1. sense the undisturbed static pressure of the stream
  2. sense the stagnation pressure of the stream
  3. measure the dynamic pressure directly
  4. reduce the drag force on the tube stem
Show answer & solution

Answer: (A) sense the undisturbed static pressure of the stream

Holes on the side, away from the nose, lie in streamlines parallel to the flow and so record static pressure; the nose opening records stagnation pressure.

Question 31

If the initial depth of water in a tank emptying through a bottom orifice is increased four times, all else unchanged, the time of emptying becomes

  1. 2 times
  2. 4 times
  3. 8 times
  4. 16 times
Show answer & solution

Answer: (A) 2 times

t = 2A√H/(Cd·a·√(2g)) ∝ √H, so quadrupling H doubles the time.

Question 32

In stream gauging with a current meter, the mean velocity in a vertical is commonly taken as the velocity measured at

  1. 0.2 of the depth below the surface
  2. 0.4 of the depth below the surface
  3. 0.6 of the depth below the surface
  4. 0.9 of the depth below the surface
Show answer & solution

Answer: (C) 0.6 of the depth below the surface

The velocity at 0.6 depth from the surface is close to the vertical mean velocity (as is the average of readings at 0.2 and 0.8 depth).

Question 33

For a sharp-edged circular orifice of diameter d, the vena contracta forms at a distance from the inner face of approximately

  1. 0.05 d
  2. 0.2 d
  3. 0.5 d
  4. 2.0 d
Show answer & solution

Answer: (C) 0.5 d

Streamlines become parallel at about half an orifice diameter downstream of the face, where the jet area is smallest.

Question 34

A cylindrical tank of cross-sectional area 4 m² contains water 4 m deep. It is emptied through a sharp-edged orifice of diameter 50 mm in its base (Cd = 0.6). The time to empty the tank is approximately

  1. 26 min
  2. 36 min
  3. 51 min
  4. 72 min
Show answer & solution

Answer: (C) 51 min

t = 2A√H/(Cd·a·√(2g)) = 2×4×2/(0.6×1.9635×10⁻³×4.429) ≈ 3066 s ≈ 51 min.

Question 35

A rotameter must be installed

  1. vertically, with the fluid flowing upward through the tube
  2. horizontally, with flow in either direction
  3. vertically, with the fluid flowing downward
  4. at any inclination, since the float weight is unimportant
Show answer & solution

Answer: (A) vertically, with the fluid flowing upward through the tube

The tube is tapered with the wider end at the top, and the float is supported by upward drag against its weight, so upward vertical flow is required.

Question 36

Water discharges through a sharp-edged circular orifice of diameter 50 mm under a constant head of 4 m. If Cd = 0.62, the discharge is approximately

  1. 5.39 L/s
  2. 7.63 L/s
  3. 8.70 L/s
  4. 10.78 L/s
Show answer & solution

Answer: (D) 10.78 L/s

Q = Cd·a·√(2gH) = 0.62 × 1.9635×10⁻³ × √(2×9.81×4) ≈ 10.78 L/s.

Question 37

A pitot-static tube in a water pipe is connected to a mercury (relative density 13.6) differential manometer that reads 100 mm. Taking the tube coefficient as unity, the velocity at the tube is approximately

  1. 1.40 m/s
  2. 3.52 m/s
  3. 4.97 m/s
  4. 5.17 m/s
Show answer & solution

Answer: (C) 4.97 m/s

h = 0.1×(13.6−1) = 1.26 m of water; v = √(2gh) = √(2×9.81×1.26) ≈ 4.97 m/s.

Question 38

An orifice is generally classified as a large orifice when the head over its centre is less than about

  1. half the vertical depth of the orifice
  2. the vertical depth of the orifice
  3. twice the vertical depth of the orifice
  4. five times the vertical depth of the orifice
Show answer & solution

Answer: (D) five times the vertical depth of the orifice

If H is less than about 5d the head varies appreciably over the opening, so the large-orifice integration is needed.

Question 39

A sharp-edged orifice has a coefficient of contraction of 0.62 and a coefficient of velocity of 0.96. Its coefficient of discharge is

  1. 0.595
  2. 0.620
  3. 0.646
  4. 1.580
Show answer & solution

Answer: (A) 0.595

Cd = Cc × Cv = 0.62 × 0.96 = 0.595.

Question 40

In an orifice meter, the downstream pressure tapping is often placed near the vena contracta because there

  1. the velocity falls to zero across the section
  2. the jet has expanded fully to the pipe diameter
  3. the pressure equals the atmospheric pressure
  4. the pressure is lowest and the differential is largest
Show answer & solution

Answer: (D) the pressure is lowest and the differential is largest

At the vena contracta the streamlines are parallel and the velocity is highest, so the pressure is minimum and the differential is greatest.

Practice these 40 questions interactively →