Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Impact of Jets and Water Wheels

Civil Engineering · Hydraulics & Fluid Mechanics

44 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

A draft tube is not required for

  1. a propeller turbine
  2. a Kaplan turbine
  3. a Pelton wheel
  4. a Francis turbine
Show answer & solution

Answer: (C) a Pelton wheel

A Pelton runner works at atmospheric pressure in air above the tailrace, so there is no pressure to recover with a draft tube.

Question 2

Which fluid-mechanics principle is used to determine the force exerted by a jet of water on the vanes of a hydraulic machine?

  1. Archimedes' principle
  2. Impulse-momentum principle
  3. Stokes' law
  4. Pascal's law
Show answer & solution

Answer: (B) Impulse-momentum principle

The force on vanes is found from the impulse-momentum principle (force = rate of change of momentum of the jet).

Question 3

The force exerted (in newton) by a jet of water impinging normally on a fixed plate is

  1. waV/g
  2. waV²/g
  3. waV/2g
  4. waV²/2g
Show answer & solution

Answer: (B) waV²/g

A jet striking a fixed plate normally loses all its momentum: F = ρaV × V = waV²/g.

Question 4

A ship with jet propulsion draws water through inlet orifices at right angles to its direction of motion. If a = area of the jet, V_r = velocity of the jet relative to the ship, v = velocity of the ship (so the absolute jet velocity is V_r − v) and w = specific weight of water, the propelling force is

  1. waV_r²/g
  2. (waV_r/2g)(V_r − v)
  3. (waV_r/g)(V_r − v)
  4. (waV_r/g)(V_r + v)
Show answer & solution

Answer: (C) (waV_r/g)(V_r − v)

Mass flow relative to the ship is waV_r/g and the absolute jet velocity is V_r − v, so F = (waV_r/g)(V_r − v).

Question 5

The runner of a reaction turbine

  1. runs dry, receiving water only through a nozzle
  2. runs in air at atmospheric pressure under a free jet
  3. runs full of water under pressure inside a casing
  4. runs partly full, with an air gap at atmospheric pressure
Show answer & solution

Answer: (C) runs full of water under pressure inside a casing

Reaction runners are enclosed in a casing and fully flooded, with pressure varying through the runner.

Question 6

For a Pelton wheel at fixed rotational speed, raising the head requires the pitch diameter to

  1. increase in proportion to H
  2. decrease in proportion to √H
  3. increase in proportion to √H
  4. remain unchanged
Show answer & solution

Answer: (C) increase in proportion to √H

Bucket speed u = φ√(2gH) = πDN/60, so at constant N the diameter D varies as √H.

Question 7

The runner blades of a reaction turbine are

  1. curved vanes shaped to guide the flow smoothly
  2. double cups with a central splitter ridge
  3. flat plates set radially on the rim
  4. straight blades with no twist along the span
Show answer & solution

Answer: (A) curved vanes shaped to guide the flow smoothly

Reaction blades are curved so the water enters shock-free and is turned gradually while its pressure falls.

Question 8

The correct relation between hydraulic efficiency (η_h), mechanical efficiency (η_m), and overall efficiency (η_o) is:

  1. η_h = η_o × η_m
  2. η_m = η_o × η_h
  3. η_o = η_h / η_m
  4. η_o = η_h × η_m
Show answer & solution

Answer: (D) η_o = η_h × η_m

Overall efficiency = hydraulic efficiency × mechanical efficiency: η_o = η_h × η_m.

Question 9

A Kaplan runner looks most like

  1. a closed impeller with many curved vanes
  2. a ship's propeller with a few twisted blades
  3. a wheel carrying many spoon-shaped buckets
  4. a paddle wheel with flat blades
Show answer & solution

Answer: (B) a ship's propeller with a few twisted blades

The Kaplan runner has a small number of broad, twisted blades on a hub, like a propeller.

Question 10

The overall efficiency of a Pelton wheel accounts for

  1. hydraulic losses plus mechanical bearing losses
  2. penstock friction losses alone
  3. mechanical bearing losses alone
  4. nozzle and bucket hydraulic losses alone
Show answer & solution

Answer: (A) hydraulic losses plus mechanical bearing losses

Overall efficiency is the product of hydraulic and mechanical efficiencies, so it includes both hydraulic and mechanical losses.

Question 11

A Pelton wheel shaft is generally mounted

  1. horizontal only, with a single jet
  2. vertical only, with several jets
  3. inclined at 45° in all installations
  4. horizontal or vertical, as the layout requires
Show answer & solution

Answer: (D) horizontal or vertical, as the layout requires

Both horizontal and vertical Pelton arrangements are used, depending on the number of jets and plant layout.

Question 12

The specific speed of a Kaplan turbine, among the main turbine types, is

  1. equal to that of a Pelton wheel
  2. equal to that of a Francis turbine
  3. the highest of the three types
  4. the lowest of the three types
Show answer & solution

Answer: (C) the highest of the three types

Kaplan turbines handle low head and large discharge, which corresponds to the highest specific speed.

Question 13

The breast water wheels are those in which:

  1. The wheel runs entirely by kinetic energy of high-speed jets
  2. The wheel runs solely by hydrostatic pressure head
  3. The wheel runs entirely by impulse on its lower blades
  4. The wheel runs partly by the weight of water and partly by impulse
Show answer & solution

Answer: (D) The wheel runs partly by the weight of water and partly by impulse

In a breast wheel water enters at about the wheel centre level, so it acts partly by weight and partly by impulse.

Question 14

The blades of a Kaplan turbine have a section similar to an

  1. thin flat plate at a fixed angle
  2. hemispherical cup, to catch the jet
  3. aerofoil, to guide the axial flow smoothly
  4. straight radial strip along the hub
Show answer & solution

Answer: (C) aerofoil, to guide the axial flow smoothly

Aerofoil-shaped blades turn the axial flow with low losses and produce lift-type torque.

Question 15

Compared with a Francis turbine, the Kaplan runner blades are

  1. adjustable only when the turbine is shut down
  2. adjustable in pitch while the turbine is running
  3. divided into cups with a splitter ridge
  4. fixed to the hub and cast with it
Show answer & solution

Answer: (B) adjustable in pitch while the turbine is running

Kaplan blades can rotate about their own axes under governor control, keeping efficiency high at part load.

Question 16

Specific speed is useful mainly because it

  1. gives the exact runner dimensions without design work
  2. gives the cost of the turbine for a given power
  3. classifies turbines and guides the choice of type for a site
  4. fixes the runner material for given conditions
Show answer & solution

Answer: (C) classifies turbines and guides the choice of type for a site

Specific speed Ns = N√P/H^(5/4) groups geometrically similar turbines, so head and power at a site indicate the suitable type.

Question 17

A Kaplan turbine installation

  1. needs no draft tube since the flow is axial
  2. uses a nozzle at the exit to restore pressure
  3. uses a draft tube to recover exit kinetic energy
  4. has a draft tube only for startup priming
Show answer & solution

Answer: (C) uses a draft tube to recover exit kinetic energy

Axial exit flow still carries kinetic energy, which the draft tube converts back into pressure head.

Question 18

A jet of water of velocity V and cross-sectional area a strikes a fixed flat plate inclined at an angle θ to the jet (w = specific weight of water). The force exerted by the jet in a direction normal to the plate is

  1. (waV²/g) × sin 2θ
  2. (waV²/g) × sin θ
  3. (waV²/g) × cos θ
  4. (waV²/2g) × sin θ
Show answer & solution

Answer: (B) (waV²/g) × sin θ

Force normal to an inclined fixed plate equals the normal component of momentum change: F = (waV²/g) sin θ.

Question 19

A jet of velocity V and area a enters tangentially at one end of a fixed symmetrical curved vane and leaves tangentially at the other end, at the same angle to the axis of the vane as at entry. The component of the force of the jet perpendicular to the axis of the vane is

  1. (waV²/g) × (cos α + cos β)
  2. Zero
  3. (waV²/g) × sin α
  4. 2waV²/g
Show answer & solution

Answer: (B) Zero

For a symmetrical vane with equal tangential entry and exit angles, the vertical (perpendicular-to-axis) momentum changes cancel, so F_y = (waV²/g)(sin α − sin β) = 0.

Question 20

The degree of reaction of a purely impulse turbine is

  1. unity
  2. zero
  3. 0.5
  4. 0.25
Show answer & solution

Answer: (B) zero

There is no pressure change across the runner of an impulse turbine, so its degree of reaction is zero.

Question 21

Among reaction turbines, the flattest part-load efficiency curve is given by the

  1. Kaplan turbine, with adjustable blades and guide vanes
  2. fixed-blade tubular turbine
  3. Francis turbine with fixed runner blades
  4. fixed-blade propeller turbine
Show answer & solution

Answer: (A) Kaplan turbine, with adjustable blades and guide vanes

Double regulation lets a Kaplan turbine keep blade angle matched to flow as load changes, so efficiency stays high at part load.

Question 22

The efficiency of jet propulsion for a ship with inlet orifices at right angles to the direction of motion of ship will be maximum when:

  1. Relative velocity equals velocity of the ship
  2. Ship velocity equals twice the jet velocity
  3. Jet velocity equals zero
  4. Relative velocity of jet and ship equals twice the velocity of the ship
Show answer & solution

Answer: (D) Relative velocity of jet and ship equals twice the velocity of the ship

η = 2(V_r − v)v/V_r² is maximum when dη/dv = 0, i.e. v = V_r/2, so V_r = 2v.

Question 23

Multiple jets are used on a single Pelton wheel mainly to

  1. handle a larger discharge without enlarging the wheel
  2. allow the wheel to run without a casing
  3. cut the discharge handled by the wheel
  4. lower the head required at the nozzle
Show answer & solution

Answer: (A) handle a larger discharge without enlarging the wheel

Several smaller jets carry more total flow at a given wheel size and speed, raising the power without an oversized jet.

Question 24

The maximum efficiency of jet propulsion of a ship with inlet orifices at right angles to the direction of motion of ship is:

  1. 40%
  2. 50%
  3. 60%
  4. 80%
Show answer & solution

Answer: (B) 50%

At v = V_r/2, η = 2(V_r/2)(V_r/2)/V_r² = 0.5, i.e. 50%.

Question 25

A jet of velocity V and area a (w = specific weight of water) strikes a series of curved vanes on a wheel so that the whole jet flow is utilised. V_w and V_w1 are the velocities of whirl at inlet and outlet (V_w1 taken positive when directed opposite to the vane motion). The force of the jet in the direction of motion of the vane is

  1. (waV/g)(V_w + V_w1)
  2. (waV/2g)(V_w + V_w1)
  3. (waV²/2g)(V_w + V_w1)
  4. (waV/g)(V_w − V_w1)
Show answer & solution

Answer: (A) (waV/g)(V_w + V_w1)

For a series of vanes the whole jet mass flow waV/g is used, so F = (waV/g)(V_w + V_w1).

Question 26

The number of blades on a Kaplan runner is usually

  1. large, about 20 to 25
  2. small, about 3 to 8
  3. moderate, about 12 to 20
  4. fixed at exactly two
Show answer & solution

Answer: (B) small, about 3 to 8

Kaplan runners use only a few broad blades to pass the large discharge at low head.

Question 27

In a reciprocating pump, the acceleration head causes its greatest increase in pipe pressure at the

  1. end of the stroke, as the piston comes to rest
  2. middle of the stroke, at peak piston velocity
  3. start of the stroke, as the piston begins to move
  4. instant at which the piston velocity is maximum
Show answer & solution

Answer: (C) start of the stroke, as the piston begins to move

Acceleration head depends on piston acceleration, which is greatest at the start of the stroke (ω²r) and zero at mid-stroke where velocity peaks.

Question 28

Unlike a Pelton wheel, a reaction turbine can use

  1. an open runner exposed to the air
  2. a draft tube to recover head down to the tailrace
  3. a nozzle to convert the whole head into velocity
  4. a free jet acting at atmospheric pressure
Show answer & solution

Answer: (B) a draft tube to recover head down to the tailrace

A reaction runner is flooded, so a draft tube lets it be set above the tailrace and still use the head down to the tailrace level.

Question 29

Where heads overlap, a Francis turbine compared with a Pelton wheel of the same power usually has

  1. a larger runner because of slower rotation
  2. a smaller and more compact runner
  3. a runner of the same diameter
  4. a larger runner with more buckets
Show answer & solution

Answer: (B) a smaller and more compact runner

A Francis runner passes a large discharge through a small diameter at higher speed, so it is more compact.

Question 30

A jet of water of velocity V strikes the centre of a single smooth symmetrical curved vane (deflecting the jet through 180°) which moves with uniform velocity in the direction of the jet. For maximum efficiency, the vane velocity is ______ of the jet velocity.

  1. One-half
  2. One-third
  3. Two-third
  4. Three-fourth
Show answer & solution

Answer: (B) One-third

For a single vane F = 2ρa(V − v)², power = F·v is maximum when d/dv[(V − v)²v] = 0, giving v = V/3.

Question 31

The working principle of jet propulsion of ships and aeroplanes is based on

  1. The buoyant force acting on the hull or body
  2. The hydrostatic pressure on the front surface
  3. The Magnus effect on rotating bodies
  4. The reaction produced by the momentum change of the issuing jet
Show answer & solution

Answer: (D) The reaction produced by the momentum change of the issuing jet

Jet propulsion works on Newton's third law: the momentum of the jet expelled backwards produces a forward reaction on the ship or aeroplane.

Question 32

A bulb turbine is essentially a variant of the

  1. Turgo turbine, with the generator in the nozzle
  2. Kaplan turbine, with the generator in a submerged bulb
  3. Francis turbine, with the spiral casing removed
  4. Pelton wheel, with a sealed underwater casing
Show answer & solution

Answer: (B) Kaplan turbine, with the generator in a submerged bulb

A bulb turbine is a horizontal axial-flow Kaplan-type unit with the generator enclosed in a streamlined bulb in the water passage.

Question 33

The ratio of the normal force of jet of water on a plate inclined at an angle of 30° as compared to that when the plate is normal to jet, is

  1. 1/√(2)
  2. 1
  3. √(2)
  4. 1/2
Show answer & solution

Answer: (D) 1/2

Normal force on an inclined plate = (waV²/g) sin θ, so ratio = sin 30° = 0.5.

Question 34

A ship is propelled by a jet with inlet orifices at right angles to the direction of motion. If V_r = velocity of the jet relative to the ship and v = velocity of the ship, the efficiency of propulsion is given by

  1. ((V_r + v)v)/(V_r)
  2. (2(V_r - v)v)/(V_r²)
  3. (2(V_r + v)v)/(V_r²)
  4. ((V_r - v)v)/(V_r)
Show answer & solution

Answer: (B) (2(V_r - v)v)/(V_r²)

Work done = F·v = (waV_r/g)(V_r − v)v and energy supplied = ½(waV_r/g)V_r², so η = 2(V_r − v)v/V_r².

Question 35

Which of the following statements about water wheels is correct?

  1. They run at slow speeds and can work with low heads
  2. They run at very high speeds and need heads above 300 m
  3. They are mostly used for power generation at heads above 100 m
  4. They have higher efficiency than modern turbines
Show answer & solution

Answer: (A) They run at slow speeds and can work with low heads

Water wheels are slow-speed machines that can work on low heads; they are not suited to high heads and are less efficient than modern turbines.

Question 36

A Francis turbine is generally suited to

  1. medium head and medium discharge
  2. very high head and low discharge
  3. high head with several small jets
  4. very low head and very high discharge
Show answer & solution

Answer: (A) medium head and medium discharge

Francis turbines fill the range between Pelton wheels (high head) and Kaplan turbines (low head).

Question 37

Governing of a turbine means

  1. keeping the head constant by controlling reservoir level
  2. keeping the efficiency constant by adjusting runner diameter
  3. setting a fixed runner speed at the time of manufacture
  4. regulating flow to keep speed nearly constant under changing load
Show answer & solution

Answer: (D) regulating flow to keep speed nearly constant under changing load

The governor adjusts guide vanes or spear position so that the speed (and generator frequency) stays nearly constant as load varies.

Question 38

A jet-propelled boat draws water through openings facing the direction of motion. If V_r = velocity of the jet relative to the boat and v = velocity of the boat, the efficiency of propulsion is given by

  1. v/(V_r + v)
  2. 2(V_r − v)v/V_r²
  3. 2v/(V_r − v)
  4. 2v/(V_r + v)
Show answer & solution

Answer: (D) 2v/(V_r + v)

For orifices facing the motion, thrust F = m(V_r − v), useful power = F v and power in the jet = ½m(V_r² − v²), giving η = 2v/(V_r + v).

Question 39

A jet of water of velocity V and cross-sectional area a strikes normally a flat plate that moves in the direction of the jet with velocity v (w = specific weight of water). The force exerted by the jet on the plate is

  1. wa(V − v)²/g
  2. waV(V − v)/g
  3. wa(V − v)²/2g
  4. wa(V − v)/g
Show answer & solution

Answer: (A) wa(V − v)²/g

The relative velocity of the jet is (V − v), so mass flow striking the plate is ρa(V − v) and F = wa(V − v)²/g.

Question 40

The specific speed of a Francis turbine is

  1. higher than that of a Kaplan turbine
  2. equal to that of a Pelton wheel
  3. higher than that of a Pelton wheel
  4. lower than that of a Pelton wheel
Show answer & solution

Answer: (C) higher than that of a Pelton wheel

Specific speed rises from Pelton (low) through Francis (medium) to Kaplan (high).

Question 41

A jet of velocity V and area a (w = specific weight of water) enters and leaves a fixed curved vane tangentially, the jet making angles α at inlet and β at outlet with the axis of the vane, both measured on the same side of the axis. The component of the force of the jet normal to the axis of the vane is

  1. (waV²/g)(sin α − sin β)
  2. (waV²/g)(cos α + cos β)
  3. (waV²/g)(sin α + sin β)
  4. (waV²/g)(cos α − cos β)
Show answer & solution

Answer: (A) (waV²/g)(sin α − sin β)

Taking momentum change perpendicular to the vane axis: F_y = (waV²/g)(sin α − sin β).

Question 42

The mechanical efficiency of a turbine is the ratio of shaft power to

  1. power in the jet at the nozzle exit
  2. power available at the generator terminals
  3. power available at the turbine inlet
  4. power delivered by the water to the runner
Show answer & solution

Answer: (D) power delivered by the water to the runner

Mechanical efficiency = shaft power / runner power, measuring only the losses in bearings and friction.

Question 43

If H_g is gross head and h_f is head lost due to friction, the net or effective head (H) is given by:

  1. H = H_g / h_f
  2. H = H_g × h_f
  3. H = H_g - h_f
  4. H = H_g + h_f
Show answer & solution

Answer: (C) H = H_g - h_f

Net head = gross head minus head lost in friction in the penstock: H = H_g − h_f.

Question 44

The undershot water wheels are those in which:

  1. The wheel runs partly by the weight and partly by impulse of water
  2. The wheel runs entirely by the weight of water
  3. The wheel runs entirely by the pressure of water in a closed casing
  4. The wheel runs entirely by the impulse of water
Show answer & solution

Answer: (D) The wheel runs entirely by the impulse of water

In an undershot wheel water strikes the lower blades and the wheel runs by the impulse of the flowing water.

Practice these 44 questions interactively →