Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Notches, Weirs & Mouthpieces

Civil Engineering · Hydraulics & Fluid Mechanics

35 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

A Cippoletti weir has a crest length of 2.0 m and works under a head of 0.25 m. Using Q = 1.86·L·H^1.5, the discharge is

  1. 0.116 m³/s
  2. 0.310 m³/s
  3. 0.465 m³/s
  4. 0.930 m³/s
Show answer & solution

Answer: (C) 0.465 m³/s

Q = 1.86(2.0)(0.25)^1.5 = 1.86×2.0×0.125 ≈ 0.465 m³/s.

Question 2

Neglecting the velocity of approach in the computation of discharge over a weir generally leads to

  1. an underestimate of the discharge
  2. an overestimate of the discharge
  3. no change in the discharge
  4. an unpredictable error of either sign
Show answer & solution

Answer: (A) an underestimate of the discharge

Approach velocity adds kinetic head ha to H, so the true discharge is larger than the value computed with H alone.

Question 3

For an external cylindrical mouthpiece running full, the absolute pressure head at the vena contracta is approximately

  1. Ha − 0.89H
  2. Ha + 0.89H
  3. Ha − 0.5H
  4. Ha
Show answer & solution

Answer: (A) Ha − 0.89H

The vena contracta lies below atmospheric pressure by about 0.89H, where H is the head over the mouthpiece.

Question 4

The maximum discharge over a broad-crested weir of length 3.0 m under an upstream head of 0.50 m (Cd = 1) is given by Q = 1.705·L·H^1.5. It equals

  1. 0.904 m³/s
  2. 1.808 m³/s
  3. 2.558 m³/s
  4. 3.617 m³/s
Show answer & solution

Answer: (B) 1.808 m³/s

Q = 1.705(3.0)(0.50)^1.5 = 1.705×3.0×0.3536 ≈ 1.808 m³/s.

Question 5

For the same percentage error in measuring the head, the percentage error in discharge is greater for a

  1. rectangular notch than for a triangular notch
  2. broad-crested weir than for a triangular notch
  3. triangular notch than for a rectangular notch
  4. rectangular notch than for a Cippoletti weir
Show answer & solution

Answer: (C) triangular notch than for a rectangular notch

dQ/Q = 2.5 dH/H for a triangular notch against 1.5 dH/H for a rectangular notch.

Question 6

An external cylindrical mouthpiece of diameter 100 mm (Cd = 0.82) discharges under a constant head of 3.0 m. The discharge is

  1. 0.0305 m³/s
  2. 0.0349 m³/s
  3. 0.0374 m³/s
  4. 0.0494 m³/s
Show answer & solution

Answer: (D) 0.0494 m³/s

Q = Cd·a·√(2gH) = 0.82(7.854×10⁻³)√(2×9.81×3.0) ≈ 0.0494 m³/s.

Question 7

In the Francis formula for a rectangular weir with two end contractions, the effective crest length is taken as

  1. L − 0.1H
  2. L − 0.2H
  3. L − 0.5H
  4. L − 2H
Show answer & solution

Answer: (B) L − 0.2H

Each end contraction reduces the length by 0.1H, so with n = 2 the effective length is L − 0.1nH = L − 0.2H.

Question 8

A stepped notch is used mainly to

  1. measure a wide range of discharges accurately
  2. reduce the effect of end contractions
  3. eliminate the velocity of approach
  4. maintain a constant head over the crest
Show answer & solution

Answer: (A) measure a wide range of discharges accurately

The combination of steps of different widths keeps the head large enough to measure both small and large flows.

Question 9

A rectangular notch 1.5 m wide (Cd = 0.60) must pass 0.18 m³/s. Neglecting end contractions and velocity of approach, the required head is

  1. 0.111 m
  2. 0.127 m
  3. 0.166 m
  4. 0.249 m
Show answer & solution

Answer: (C) 0.166 m

H^1.5 = Q/[(2/3)Cd√(2g)L] = 0.18/(0.4×4.429×1.5) = 0.0677; H = 0.0677^(2/3) ≈ 0.166 m.

Question 10

A convergent mouthpiece gives its maximum coefficient of discharge, about 0.97, at a convergence angle of approximately

  1. 5°
  2. 30°
  3. 13.5°
  4. 60°
Show answer & solution

Answer: (C) 13.5°

Experiments show a maximum Cd of about 0.97 at a cone angle near 13°24′.

Question 11

When an ogee spillway operates at a head greater than the design head, the crest is exposed to

  1. higher positive pressures with a risk of uplift
  2. uniform atmospheric pressure at all points
  3. zero velocity at the crest and no risk
  4. negative (sub-atmospheric) pressures with a risk of cavitation
Show answer & solution

Answer: (D) negative (sub-atmospheric) pressures with a risk of cavitation

A higher head makes the nappe tend to spring clear of the profile, creating sub-atmospheric pressures on the crest.

Question 12

The discharge through a trapezoidal notch is computed as the discharge through

  1. a rectangular notch minus that through a triangular notch
  2. a triangular notch only, using the top width
  3. two rectangular notches of equal width
  4. a rectangular notch plus that through a triangular notch
Show answer & solution

Answer: (D) a rectangular notch plus that through a triangular notch

The trapezoid is split into a central rectangle and two half-triangles, which together form one V-notch.

Question 13

Discharge over a rectangular notch of width 1.2 m under a head of 0.30 m, taking Cd = 0.62 (ignore end contractions and velocity of approach), is

  1. 0.108 m³/s
  2. 0.241 m³/s
  3. 0.361 m³/s
  4. 0.542 m³/s
Show answer & solution

Answer: (C) 0.361 m³/s

Q = (2/3)Cd·L·√(2g)·H^1.5 = (2/3)(0.62)(1.2)(4.429)(0.30)^1.5 ≈ 0.361 m³/s.

Question 14

When computing the discharge of a submerged sharp-crested weir with the two-part method, the flow is divided into

  1. a surface part and a bottom part with equal heads
  2. a free-flow part under the head difference and a drowned part through the tailwater depth
  3. an aerated part and a non-aerated part
  4. a part over the crest and a part through the nappe
Show answer & solution

Answer: (B) a free-flow part under the head difference and a drowned part through the tailwater depth

The portion over the tailwater level acts as a free weir under (H1 − h), while the drowned portion behaves like an orifice of depth h.

Question 15

A Borda (re-entrant) mouthpiece of diameter 50 mm runs free under a constant head of 2.0 m. The discharge is

  1. 6.15 L/s
  2. 7.63 L/s
  3. 12.30 L/s
  4. 24.60 L/s
Show answer & solution

Answer: (A) 6.15 L/s

Cd = 0.5, so Q = 0.5·a·√(2gH) = 0.5(1.963×10⁻³)√(2×9.81×2.0) ≈ 6.15 L/s.

Question 16

In a convergent-divergent mouthpiece, if the pressure at the vena contracta falls to the vapour pressure of water, then

  1. the discharge is doubled
  2. the jet becomes supersonic
  3. the coefficient of velocity becomes greater than one
  4. cavitation occurs and the discharge cannot increase further
Show answer & solution

Answer: (D) cavitation occurs and the discharge cannot increase further

Vapour pressure at the throat limits the maximum head that can be effectively used and causes cavitation.

Question 17

A tank of constant plan area 20 m² discharges over a rectangular weir 1.0 m long (Cd = 0.60). The time for the head over the crest to fall from 0.50 m to 0.10 m is

  1. 19.7 s
  2. 26.3 s
  3. 39.5 s
  4. 78.9 s
Show answer & solution

Answer: (C) 39.5 s

T = 2A(1/√H2 − 1/√H1)/[(2/3)Cd√(2g)L] = 2(20)(3.162 − 1.414)/1.772 ≈ 39.5 s.

Question 18

For accurate measurement over a sharp-crested weir, the head H should be measured

  1. at the crest section itself
  2. in still water well upstream of the weir, at about 3 to 4 times H
  3. immediately downstream of the nappe
  4. at the vena contracta of the nappe
Show answer & solution

Answer: (B) in still water well upstream of the weir, at about 3 to 4 times H

The water surface draws down near the crest, so H must be taken upstream where the surface is unaffected.

Question 19

If the nappe below a fully contracted sharp-crested weir is not ventilated, the discharge will

  1. decrease because the nappe thickens
  2. remain unchanged because the head is fixed
  3. increase as the pressure beneath the nappe falls below atmospheric
  4. become independent of the upstream head
Show answer & solution

Answer: (C) increase as the pressure beneath the nappe falls below atmospheric

Entrained air is removed, pressure under the nappe drops and the nappe is drawn down, increasing the discharge for the same head.

Question 20

A 60° triangular notch (Cd = 0.60) works under a head of 0.20 m. The discharge is

  1. 14.6 L/s
  2. 25.4 L/s
  3. 43.9 L/s
  4. 73.2 L/s
Show answer & solution

Answer: (A) 14.6 L/s

Q = (8/15)Cd√(2g)tan(30°)H^2.5 = (8/15)(0.60)(4.429)(0.5774)(0.20)^2.5 ≈ 14.6 L/s.

Question 21

A Borda (re-entrant) mouthpiece running full has a coefficient of discharge, based on the outlet area, of about

  1. 0.50
  2. 0.707
  3. 0.82
  4. 0.97
Show answer & solution

Answer: (B) 0.707

Running full, the jet expands to the full outlet so Cc = 1, and the Borda-Carnot loss gives Cv ≈ 0.707, hence Cd ≈ 0.707 (compared with 0.5 when running free).

Question 22

In the time-of-emptying formula for a tank discharging over a weir, the time to lower the head from H1 to H2 is proportional to

  1. (√H1 − √H2)
  2. (H1^1.5 − H2^1.5)
  3. (1/H2 − 1/H1)
  4. (1/√H2 − 1/√H1)
Show answer & solution

Answer: (D) (1/√H2 − 1/√H1)

Integrating A·dH = −K·H^1.5 dt gives T = (2A/K)(1/√H2 − 1/√H1).

Question 23

In a V-notch, the head is measured with a positive error of 1.5%. The resulting percentage error in the computed discharge is about

  1. 1.50 %
  2. 2.25 %
  3. 3.00 %
  4. 3.75 %
Show answer & solution

Answer: (D) 3.75 %

Q ∝ H^2.5, so dQ/Q = 2.5 × dH/H = 2.5 × 1.5% = 3.75%.

Question 24

The side slopes of a Cippoletti (trapezoidal) weir are

  1. 1 horizontal to 1 vertical
  2. 4 horizontal to 1 vertical
  3. 1 horizontal to 4 vertical
  4. 1 horizontal to 2 vertical
Show answer & solution

Answer: (C) 1 horizontal to 4 vertical

Cippoletti used a 1H : 4V side slope so that the extra flow through the sloping sides offsets the loss due to end contractions.

Question 25

A right-angled (90°) triangular notch with Cd = 0.60 works under a head of 0.25 m. The discharge is

  1. 0.0443 m³/s
  2. 0.0554 m³/s
  3. 0.1772 m³/s
  4. 0.2215 m³/s
Show answer & solution

Answer: (A) 0.0443 m³/s

Q = (8/15)Cd·√(2g)·tan(θ/2)·H^2.5 = (8/15)(0.60)(4.429)(1)(0.25)^2.5 ≈ 0.0443 m³/s.

Question 26

For a broad-crested weir with free flow, the maximum discharge occurs when the depth of water over the crest is equal to

  1. 1/3 of the upstream head
  2. 2/3 of the upstream head
  3. 1/2 of the upstream head
  4. 3/4 of the upstream head
Show answer & solution

Answer: (B) 2/3 of the upstream head

Maximising Q = L·h·√(2g(H − h)) gives h = 2H/3, which is the critical depth over the crest.

Question 27

An ogee spillway of effective length 10 m has Cd = 0.74 and operates under a head of 1.5 m. Using Q = (2/3)Cd·√(2g)·L·H^1.5, the discharge is

  1. 40.1 m³/s
  2. 60.2 m³/s
  3. 80.3 m³/s
  4. 90.3 m³/s
Show answer & solution

Answer: (A) 40.1 m³/s

Q = (2/3)(0.74)(4.429)(10)(1.5)^1.5 ≈ 40.1 m³/s.

Question 28

Which statement best distinguishes a notch from a weir?

  1. A notch has a flat crest, while a weir always has a V-shaped opening
  2. A notch measures only large flows, while a weir measures only small flows
  3. A notch is an opening in the side of a tank, while a weir is an overflow structure built across a stream
  4. A notch is submerged, while a weir always discharges freely
Show answer & solution

Answer: (C) A notch is an opening in the side of a tank, while a weir is an overflow structure built across a stream

Both measure flow by the head over the crest, but a notch is cut in the tank wall and a weir is a structure over which a stream flows.

Question 29

The main advantage of a Cippoletti weir over a rectangular weir with end contractions is that

  1. it can measure much smaller discharges accurately
  2. its discharge varies as H^2.5 instead of H^1.5
  3. its crest need not be kept sharp and level
  4. no end-contraction correction is needed in its discharge formula
Show answer & solution

Answer: (D) no end-contraction correction is needed in its discharge formula

The trapezoidal shape compensates for end contractions, so Q = 1.86LH^1.5 can be used directly.

Question 30

The coefficient of contraction of a Borda (re-entrant) mouthpiece running free is

  1. 0.62
  2. 0.5
  3. 0.707
  4. 0.97
Show answer & solution

Answer: (B) 0.5

Momentum analysis gives Cc = 0.5 and, since Cv ≈ 1, Cd = 0.5.

Question 31

Using the Francis formula Q = 1.84(L − 0.1nH)H^1.5, find the discharge over a rectangular weir 2.0 m long with two end contractions under a head of 0.40 m.

  1. 0.357 m³/s
  2. 0.894 m³/s
  3. 0.912 m³/s
  4. 0.931 m³/s
Show answer & solution

Answer: (B) 0.894 m³/s

Effective length = 2.0 − 0.1(2)(0.40) = 1.92 m; Q = 1.84(1.92)(0.40)^1.5 ≈ 0.894 m³/s.

Question 32

Water approaches a weir with a mean velocity of 1.5 m/s. The head due to velocity of approach is

  1. 0.0287 m
  2. 0.0573 m
  3. 0.0765 m
  4. 0.1147 m
Show answer & solution

Answer: (D) 0.1147 m

ha = Va²/(2g) = 1.5²/(2×9.81) ≈ 0.1147 m.

Question 33

The theoretical time to lower the water level in a tank all the way to the crest of a discharging weir (H2 = 0) is

  1. infinite, because the discharge tends to zero as H tends to zero
  2. zero, because the tank empties instantly
  3. finite and equal to 2A/(K√H1)
  4. equal to the time for half the volume to drain
Show answer & solution

Answer: (A) infinite, because the discharge tends to zero as H tends to zero

As H2 → 0 the term 1/√H2 tends to infinity, so the time is unbounded.

Question 34

A rectangular weir 2.0 m long is drowned: upstream head over crest H1 = 0.60 m and downstream head h = 0.20 m. With Cd1 = 0.60 and Cd2 = 0.80, using Q = (2/3)Cd1·L√(2g)(H1 − h)^1.5 + Cd2·L·h·√(2g(H1 − h)), the discharge is

  1. 0.90 m³/s
  2. 1.79 m³/s
  3. 1.99 m³/s
  4. 2.69 m³/s
Show answer & solution

Answer: (B) 1.79 m³/s

Free part = 0.896 m³/s; drowned part = 0.80(2.0)(0.20)√(2×9.81×0.40) = 0.896 m³/s; total ≈ 1.79 m³/s.

Question 35

The profile of the crest of an ogee spillway is shaped to follow

  1. the underside of the lower nappe of a ventilated sharp-crested weir
  2. a single curved arc tangent to the dam face
  3. the upper surface of the free nappe
  4. a straight inclined plane at 45°
Show answer & solution

Answer: (A) the underside of the lower nappe of a ventilated sharp-crested weir

At the design head the flow just touches the crest, so the pressure on it is near atmospheric.

Practice these 35 questions interactively →