Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.
Hydraulics & Fluid Mechanics: Impulse Turbines and Pelton Wheel
Civil Engineering · Hydraulics & Fluid Mechanics
50 questions, each with the answer and a worked solution. Notes on units and constants are at the top.
Practice interactively and track your score →Units and constants
SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.
Question 1
The hydraulic efficiency of an ideal Pelton wheel (no friction, 180° deflection, u = V/2) is
- 50%
- 100%
- 65%
- 80%
Show answer & solution
Answer: (B) 100%
With u = V/2 and 180° deflection the water leaves with zero absolute velocity, so all jet kinetic energy is transferred to the wheel.
Question 2
The mechanical efficiency of an impulse turbine is defined as the ratio of:
- Work done on wheel to energy of jet
- Actual power produced at the shaft to the energy imparted to the wheel
- Net effective head to gross head
- Water power at the nozzle to the shaft power
Show answer & solution
Answer: (B) Actual power produced at the shaft to the energy imparted to the wheel
Mechanical efficiency = shaft power / power developed on the wheel (energy imparted to the wheel).
Question 3
An impulse turbine is used for:
- Medium head of water
- Low head of water
- High discharge with zero head
- High head of water
Show answer & solution
Answer: (D) High head of water
Impulse turbines (Pelton wheels) are used for high heads and low discharge.
Question 4
Which turbine type is preferred for a specific speed range of 60 to 300 r.p.m.?
- Pelton wheel
- Kaplan turbine
- Francis turbine
- Propeller turbine
Show answer & solution
Answer: (C) Francis turbine
Francis turbines are used for specific speeds of about 60 to 300 r.p.m.
Question 5
At entry to a Pelton bucket, the relative velocity of the jet is
- absolute jet velocity, regardless of bucket motion
- jet velocity plus bucket velocity
- geometric mean of jet and bucket velocities
- jet velocity minus bucket velocity
Show answer & solution
Answer: (D) jet velocity minus bucket velocity
The jet and bucket move along the same line, so the relative velocity is Vr1 = V1 − u.
Question 6
A Pelton wheel gives maximum theoretical hydraulic efficiency when the bucket speed is
- half the jet velocity
- equal to the jet velocity
- two-thirds of the jet velocity
- one-third of the jet velocity
Show answer & solution
Answer: (A) half the jet velocity
Work output is proportional to u(V−u), which is maximum at u = V/2.
Question 7
The overall efficiency for a Pelton wheel generally lies between:
- 0.50 to 0.65
- 0.65 to 0.75
- 0.75 to 0.85
- 0.85 to 0.90
Show answer & solution
Answer: (D) 0.85 to 0.90
Typical overall efficiency of a Pelton wheel is 0.85 to 0.90.
Question 8
A Pelton wheel develops 1750 kW under a head of 100 m while running at 200 r.p.m. and discharging 2.5 m³/s. The unit power of the wheel is:
- 0.25 kW
- 1.75 kW
- 3.75 kW
- 17.5 kW
Show answer & solution
Answer: (B) 1.75 kW
Unit power P_u = P/H^(3/2) = 1750/100^1.5 = 1750/1000 = 1.75 kW.
Question 9
For a high head of 450 m, which turbine shall be used?
- Francis turbine
- Pelton wheel
- Low-head propeller turbine
- Kaplan turbine
Show answer & solution
Answer: (B) Pelton wheel
At 450 m head (high head, low discharge) a Pelton wheel is the appropriate turbine.
Question 10
The number of buckets on a Pelton wheel is determined empirically from the
- rotational speed of the shaft
- net head at the nozzle
- jet ratio of the wheel
- rated discharge of the jet
Show answer & solution
Answer: (C) jet ratio of the wheel
An empirical relation Z = 15 + m/2 ties the bucket count to the jet ratio m so that every jet portion is intercepted by a bucket.
Question 11
A Pelton wheel develops 1750 kW under a head of 100 m while running at 200 r.p.m. and discharging 2.5 m³/s. The unit discharge of the wheel is
- 0.25 m³/s
- 0.5 m³/s
- 1.5 m³/s
- 2.5 m³/s
Show answer & solution
Answer: (A) 0.25 m³/s
Unit discharge Q_u = Q/√H = 2.5/√100 = 0.25 m³/s.
Question 12
In an impulse turbine, the pressure of water both at entering and leaving the vanes is:
- Equal to saturation vapor pressure
- Atmospheric pressure
- High gauge pressure
- Sub-atmospheric vacuum pressure
Show answer & solution
Answer: (B) Atmospheric pressure
The jet leaves the nozzle at atmospheric pressure and the runner is exposed to atmosphere, so pressure is atmospheric at inlet and outlet.
Question 13
A Pelton wheel working under constant head and discharge has maximum efficiency when speed ratio is approximately:
- 0.26
- 0.36
- 0.46
- 0.56
Show answer & solution
Answer: (C) 0.46
The Pelton wheel gives maximum efficiency at a speed ratio of about 0.45 (bucket speed about half the jet speed).
Question 14
A draft tube is used with impulse turbines:
- Never, since the runner is at atmospheric pressure above the tailrace
- Always, to recover the kinetic energy at outlet
- Only in double-overhung configurations
- Only when the head exceeds 500 m
Show answer & solution
Answer: (A) Never, since the runner is at atmospheric pressure above the tailrace
The Pelton runner is above the tailrace at atmospheric pressure, so no draft tube is used.
Question 15
Because of friction in the Pelton bucket, the relative exit velocity is
- nearly equal to the bucket velocity
- equal to the relative entry velocity
- slightly less than the relative entry velocity
- slightly more than the relative entry velocity
Show answer & solution
Answer: (C) slightly less than the relative entry velocity
Surface friction reduces the relative velocity, so Vr2 = k·Vr1 with k less than 1, typically 0.85 to 0.95.
Question 16
A Pelton wheel develops 1750 kW under a head of 100 m while running at 200 r.p.m. and discharging 2.5 m³/s. The unit speed of the wheel is
- 10 r.p.m.
- 20 r.p.m.
- 40 r.p.m.
- 80 r.p.m.
Show answer & solution
Answer: (B) 20 r.p.m.
Unit speed N_u = N/√H = 200/√100 = 20 r.p.m.
Question 17
The speed ratio of a Pelton wheel is the ratio of the bucket speed to
- the relative velocity at bucket exit
- the actual jet velocity leaving the nozzle
- the relative velocity at bucket entry
- the theoretical jet velocity √(2gH)
Show answer & solution
Answer: (D) the theoretical jet velocity √(2gH)
Speed ratio φ = u/√(2gH), comparing the bucket speed with the velocity corresponding to the full net head.
Question 18
A Pelton wheel with one nozzle is preferred for a specific speed between:
- 10 to 35 r.p.m.
- 35 to 60 r.p.m.
- 100 to 250 r.p.m.
- 300 to 600 r.p.m.
Show answer & solution
Answer: (A) 10 to 35 r.p.m.
A single-jet Pelton wheel is suited to specific speeds of 10 to 35 r.p.m.; two or more jets for 35 to 60 r.p.m.
Question 19
Which of the following is NOT a reaction turbine?
- Jonval turbine
- Furneyron turbine
- Thomson’s turbine
- Pelton wheel
Show answer & solution
Answer: (D) Pelton wheel
Pelton wheel is an impulse turbine; Furneyron, Jonval and Thomson are reaction turbines.
Question 20
Which of the following statements is WRONG?
- Reaction turbines are used for low head and high discharge.
- The angle of taper on a draft tube is kept less than 8°.
- An impulse turbine is generally fitted slightly above the tailrace.
- A Francis turbine is classified as an impulse turbine.
Show answer & solution
Answer: (D) A Francis turbine is classified as an impulse turbine.
Francis turbine is a reaction (inward/mixed flow) turbine, not an impulse turbine, so the statement is wrong.
Question 21
A turbine is required to develop 1500 kW at 300 r.p.m. under a head of 150 m. Which turbine should be used?
- Pelton wheel with one nozzle
- Low-head Francis turbine
- Kaplan turbine
- Pelton wheel with two or more nozzles
Show answer & solution
Answer: (A) Pelton wheel with one nozzle
N_s = N√P/H^(5/4) = 300√1500/150^1.25 ≈ 22, which lies in the 10 to 35 range for a single-jet Pelton wheel.
Question 22
The overall efficiency of an impulse turbine is the ratio of:
- Runner speed to jet velocity
- Outlet velocity head to inlet head
- Mechanical work to hydraulic friction losses
- Shaft power produced to the water power supplied
Show answer & solution
Answer: (D) Shaft power produced to the water power supplied
Overall efficiency = shaft power / water power supplied = η_h × η_m.
Question 23
The maximum number of jets generally employed in an impulse turbine without jet interference is:
- Eight
- Two
- Four
- Six
Show answer & solution
Answer: (D) Six
In practice not more than six jets are used in an impulse turbine to avoid jet interference.
Question 24
The efficiency of a Pelton wheel working under constant head …………… with increase in power up to design limit.
- Remains same
- Increases
- Decreases
- Fluctuates erratically
Show answer & solution
Answer: (B) Increases
Efficiency of a Pelton wheel rises with increasing power (load) up to the design point, after which it falls.
Question 25
In an impulse turbine, the available head is converted entirely into kinetic energy by the
- guide vanes, with pressure kept in the casing
- draft tube, after the water leaves the runner
- nozzle, before the jet meets the runner
- runner, as water passes between the blades
Show answer & solution
Answer: (C) nozzle, before the jet meets the runner
An impulse turbine converts the whole head into jet velocity in the nozzle, so the runner works at atmospheric pressure.
Question 26
The spear (needle) in a Pelton wheel nozzle is used to
- split the jet into two equal streams
- raise the jet velocity by narrowing the flow
- regulate the flow by varying the nozzle area
- divert the jet away from the buckets at load rejection
Show answer & solution
Answer: (C) regulate the flow by varying the nozzle area
Moving the spear changes the annular nozzle opening and so the discharge, while the jet velocity stays almost constant.
Question 27
The velocity of the jet issuing from the nozzle of a Pelton wheel is
- V = Cv√(gH)
- V = Cv√(2gH)
- V = Cv·2gH
- V = Cv·H/√(2g)
Show answer & solution
Answer: (B) V = Cv√(2gH)
Applying Bernoulli across the nozzle gives V = Cv√(2gH), where Cv is the velocity coefficient and H the net head.
Question 28
A double overhung Pelton wheel is characterized by having:
- Two jets per runner
- Four jets total
- Two runners on a single shaft
- Four independent runners
Show answer & solution
Answer: (C) Two runners on a single shaft
A double overhung Pelton wheel has two runners mounted on a single shaft, one at each end.
Question 29
The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is …………. of the jet velocity.
- One-fourth
- One-half
- Three-fourth
- Double
Show answer & solution
Answer: (B) One-half
η_h = 2(V − v)v(1 + cos φ)/V² is maximum at v = V/2.
Question 30
A Pelton wheel is most suitable for sites with
- very low head and moderate discharge
- high head and comparatively low discharge
- medium head and very large discharge
- low head and comparatively high discharge
Show answer & solution
Answer: (B) high head and comparatively low discharge
A high head gives a fast jet through a small nozzle, so Pelton wheels suit high head and low flow.
Question 31
The buckets of a Pelton wheel turn the jet through an angle of approximately
- 120° to 130°
- 90° to 100°
- 165° to 170°
- 45° to 60°
Show answer & solution
Answer: (C) 165° to 170°
Deflection is kept slightly below 180° so the exiting water clears the next bucket, while still giving near-maximum momentum change.
Question 32
The depth of the bucket for a Pelton wheel is generally ……………. the diameter of the jet.
- Equal to
- 1.2 times
- 1.8 times
- Double
Show answer & solution
Answer: (B) 1.2 times
Standard design proportion: bucket depth = 1.2 × jet diameter.
Question 33
The jet ratio is defined as the ratio of:
- Pitch circle diameter of wheel to jet diameter
- Velocity of wheel to velocity of jet
- Velocity of jet to velocity of Pelton wheel
- Diameter of jet to diameter of Pelton wheel
Show answer & solution
Answer: (A) Pitch circle diameter of wheel to jet diameter
Jet ratio m = D/d, the ratio of pitch circle diameter of the wheel to the jet diameter.
Question 34
For maximum efficiency, the speed ratio of a Pelton wheel is typically
- 0.60 to 0.65
- 0.45 to 0.48
- 0.25 to 0.30
- 0.80 to 0.85
Show answer & solution
Answer: (B) 0.45 to 0.48
The ideal value is 0.5 for the jet velocity; with nozzle losses the best practical speed ratio is slightly lower, about 0.45 to 0.48.
Question 35
Which of the following statements correctly contrasts impulse and reaction turbines?
- Impulse: free jet at atmospheric pressure; reaction: pressure flow with a drop across the runner
- Reaction turbines operate purely on the static weight of the water on buckets
- Impulse turbines always require a draft tube at the runner outlet to work
- Reaction turbines keep a constant pressure across the runner vanes
Show answer & solution
Answer: (A) Impulse: free jet at atmospheric pressure; reaction: pressure flow with a drop across the runner
In impulse turbines pressure is atmospheric across the runner; in reaction turbines water flows under pressure with a pressure drop across the runner.
Question 36
The number of buckets on the periphery of a Pelton wheel is given by the empirical relation:
- D/2d + 20
- D/2d + 5
- D/2d + 15
- D/2d + 10
Show answer & solution
Answer: (C) D/2d + 15
Empirical relation for number of buckets: Z = D/2d + 15.
Question 37
Braking jet in an impulse turbine is used to:
- Break the high-pressure water jet into droplets
- Change the direction of rotation of runner
- Bring the runner to rest in a short time
- Regulate governor speed during peak loads
Show answer & solution
Answer: (C) Bring the runner to rest in a short time
A braking jet is directed on the back of the buckets to stop the runner quickly after the main nozzle is closed.
Question 38
A typical jet ratio for a practical Pelton wheel is about
- 4, in the range 3 to 6
- 30, in the range 25 to 40
- 12, in the range 11 to 16
- 2, in the range 1.5 to 2.5
Show answer & solution
Answer: (C) 12, in the range 11 to 16
Practical Pelton wheels have a pitch diameter roughly 11 to 16 times the jet diameter.
Question 39
Which turbine is preferred for very low heads (0 to 25 m of water)?
- Francis turbine
- Multi-stage impulse turbine
- Kaplan turbine
- Pelton wheel
Show answer & solution
Answer: (C) Kaplan turbine
Kaplan (adjustable-blade axial flow) turbines are used for very low heads (below about 25 m).
Question 40
A Pelton wheel is classified as a:
- Outward flow impulse turbine
- Tangential flow impulse turbine
- Inward flow reaction turbine
- Inward flow impulse turbine
Show answer & solution
Answer: (B) Tangential flow impulse turbine
In a Pelton wheel the jet strikes the buckets tangentially to the runner, so it is a tangential flow impulse turbine.
Question 41
The splitter ridge at the centre of a Pelton bucket serves to
- divide the jet into two equal streams
- raise the jet velocity before it leaves
- absorb part of the jet as storage
- lower the friction on the bucket back
Show answer & solution
Answer: (A) divide the jet into two equal streams
The ridge splits the jet into two halves that flow smoothly around the cups, avoiding shock and axial thrust.
Question 42
The width of the bucket for a Pelton wheel is generally ……………. the diameter of the jet.
- Double
- Three times
- Four times
- Five times
Show answer & solution
Answer: (D) Five times
Standard design proportion: bucket width = 5 × jet diameter.
Question 43
Which of the following is NOT an impulse turbine?
- Pelton wheel
- Girard turbine
- Turgo turbine
- Kaplan turbine
Show answer & solution
Answer: (D) Kaplan turbine
Kaplan turbine is an axial flow reaction turbine; Girard, Turgo and Pelton are impulse turbines.
Question 44
The buckets of a Pelton wheel are shaped as
- flat plates fixed radially on the rim
- single curved vanes with no central ridge
- double cups with a central splitter ridge
- straight blades set parallel to the shaft
Show answer & solution
Answer: (C) double cups with a central splitter ridge
The double-cup bucket with a central splitter divides the jet symmetrically and turns it through nearly 180°.
Question 45
In an impulse turbine, how does the jet of water interact with the buckets?
- Jet enters with low velocity and leaves with high velocity
- Jet strikes with high kinetic energy at atmospheric pressure
- Jet strikes with high pressure energy that drops to zero
- Jet flows under continuous pressure drop across the runner
Show answer & solution
Answer: (B) Jet strikes with high kinetic energy at atmospheric pressure
In an impulse turbine the whole available head is converted into kinetic energy in the nozzle; pressure stays atmospheric across the buckets.
Question 46
A jet deflector in a Pelton installation is used mainly to
- divert the jet from the buckets during load rejection
- raise the runner speed during start-up
- increase the head at the nozzle
- control the jet by changing nozzle area
Show answer & solution
Answer: (A) divert the jet from the buckets during load rejection
The deflector diverts the jet quickly to prevent overspeed, while the needle closes slowly to avoid water hammer in the penstock.
Question 47
The maximum hydraulic efficiency of an impulse turbine is given by:
- (1 - cos φ)/(2)
- (1 - sin φ)/(2)
- (1 + sin φ)/(2)
- (1 + cos φ)/(2)
Show answer & solution
Answer: (D) (1 + cos φ)/(2)
At v = V/2, η_max = (1 + cos φ)/2.
Question 48
The hydraulic efficiency of an impulse turbine is defined as the ratio of:
- Actual work available at turbine to energy imparted to wheel
- Work done on the wheel to the kinetic energy of the jet
- Actual power produced to energy supplied
- Kinetic energy of the jet to the work done on the wheel
Show answer & solution
Answer: (B) Work done on the wheel to the kinetic energy of the jet
Hydraulic efficiency = work done on the wheel / energy (kinetic energy of the jet) supplied.
Question 49
The work done per second by a Pelton jet on the runner is found from the
- impulse-momentum principle using relative velocity
- buoyant force on the submerged bucket
- hydrostatic force on the bucket surface
- continuity relation between jet and bucket area
Show answer & solution
Answer: (A) impulse-momentum principle using relative velocity
The force on the bucket equals the rate of change of momentum of the jet relative to the moving bucket, and power is that force times bucket speed.
Question 50
A Kaplan turbine is classified as:
- A mixed flow high head turbine
- An axial flow reaction turbine
- A tangential impulse turbine
- A radial flow reaction turbine
Show answer & solution
Answer: (B) An axial flow reaction turbine
Kaplan turbine has axial flow through the runner and is a reaction turbine with adjustable blades.