Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Fluid Mechanics: Questions 101–150

Civil Engineering · Hydraulics & Fluid Mechanics

50 questions, each with the answer and a worked solution. Sections: Flow Measurement (Venturimeter, Orifices, Pitot) (11), Notches, Weirs & Mouthpieces (5), Pipe Flow, Losses & Water Hammer (17) and Open Channels, Vortex Flow & Similitude (17).

Practice interactively and track your score →

Flow Measurement (Venturimeter, Orifices, Pitot)

Question 1

A venturimeter consists mainly of a

  1. uniform pipe with a small orifice
  2. converging section, a throat (constricted section), and a diverging section
  3. sudden, sharp constriction with no gradual transition
  4. a simple straight pipe
Show answer & solution

Answer: (B) converging section, a throat (constricted section), and a diverging section

The gradual converging-throat-diverging geometry of a venturimeter minimizes energy loss compared to an abrupt constriction.

Question 2

The coefficient of discharge of a venturimeter is generally

  1. less than that of an orifice meter, due to greater internal losses
  2. higher than that of an orifice meter, due to its smooth, gradual transitions minimizing energy loss
  3. always exactly 1
  4. always zero
Show answer & solution

Answer: (B) higher than that of an orifice meter, due to its smooth, gradual transitions minimizing energy loss

The venturimeter's smooth transitions reduce turbulence and losses, giving it a higher Cd than an orifice meter.

Question 3

An orifice meter, compared to a venturimeter, is generally

  1. more expensive but has lower losses
  2. cheaper and more compact, but causes greater energy loss (lower coefficient of discharge)
  3. identical in every respect
  4. not based on Bernoulli's principle at all
Show answer & solution

Answer: (B) cheaper and more compact, but causes greater energy loss (lower coefficient of discharge)

The orifice meter trades a lower Cd (more loss) for a simpler, cheaper, more compact design.

Question 4

An orifice is a small opening, of any cross-section, provided in the

  1. top of a tank only
  2. side or bottom of a tank or vessel, through which fluid flows out
  3. middle of a pipe only, never in a tank
  4. atmosphere directly
Show answer & solution

Answer: (B) side or bottom of a tank or vessel, through which fluid flows out

Orifices are typically openings in the side or bottom of a vessel used to discharge fluid.

Question 5

The coefficient of contraction (Cc) of an orifice is defined as the ratio of the

  1. area of the jet at the vena contracta to the area of the orifice
  2. area of the orifice to the area of the jet
  3. actual velocity to theoretical velocity
  4. actual discharge to theoretical discharge
Show answer & solution

Answer: (A) area of the jet at the vena contracta to the area of the orifice

Cc = jet area at vena contracta / orifice area, capturing the jet's narrowing after exit.

Question 6

The coefficient of discharge (Cd) of an orifice is defined as the ratio of the

  1. actual discharge to the theoretical discharge, and equals Cv × Cc
  2. theoretical discharge to actual discharge
  3. coefficient of velocity alone
  4. coefficient of contraction alone
Show answer & solution

Answer: (A) actual discharge to the theoretical discharge, and equals Cv × Cc

Cd combines both velocity and contraction effects: Cd = Cv × Cc.

Question 7

A mouthpiece is essentially

  1. a small tube of length about two to three times its diameter, fitted to an orifice to increase discharge
  2. a very long pipe
  3. a type of pressure gauge
  4. a device used only for pressure measurement
Show answer & solution

Answer: (A) a small tube of length about two to three times its diameter, fitted to an orifice to increase discharge

A mouthpiece is a short attached tube (typically 2-3 diameters long) that modifies flow through an orifice.

Question 8

An external cylindrical mouthpiece, compared to a plain orifice of the same diameter, generally

  1. reduces the discharge
  2. increases the discharge, since the vena contracta forms inside the mouthpiece and the jet fills the full mouthpiece diameter at exit
  3. has no effect on discharge
  4. causes the flow to stop entirely
Show answer & solution

Answer: (B) increases the discharge, since the vena contracta forms inside the mouthpiece and the jet fills the full mouthpiece diameter at exit

The internal vena contracta re-expands to fill the mouthpiece, increasing the effective discharge area at exit and thus discharge.

Question 9

A pitot tube is an instrument used to measure the

  1. discharge in a pipe directly
  2. local (point) velocity of flow, based on the stagnation pressure principle
  3. viscosity of the fluid
  4. density of the fluid
Show answer & solution

Answer: (B) local (point) velocity of flow, based on the stagnation pressure principle

A pitot tube measures local velocity from the stagnation pressure rise it creates in the flow.

Question 10

A pitot tube works on the principle that the difference between the stagnation pressure and the static pressure at a point equals the

  1. velocity head at that point
  2. pressure head only
  3. datum head
  4. total head only
Show answer & solution

Answer: (A) velocity head at that point

Stagnation pressure minus static pressure equals the dynamic (velocity) pressure head at that point.

Question 11

A pitot-static tube combines the measurement of

  1. stagnation pressure and static pressure at the same location, to directly give the velocity head
  2. only static pressure
  3. only stagnation pressure
  4. temperature and pressure
Show answer & solution

Answer: (A) stagnation pressure and static pressure at the same location, to directly give the velocity head

Combining both pressure measurements in one probe lets a pitot-static tube directly yield local velocity.

Notches, Weirs & Mouthpieces

Question 12

Weirs and notches are structures used mainly to measure the

  1. velocity at a point
  2. rate of flow (discharge) in open channels
  3. pressure in a pipe
  4. viscosity of the flowing liquid
Show answer & solution

Answer: (B) rate of flow (discharge) in open channels

Weirs/notches relate the upstream head to discharge, serving as open-channel flow meters.

Question 13

A rectangular notch is a device where discharge is calculated using a formula involving the head H raised to the power of

  1. 1
  2. 3/2
  3. 5/2
  4. 2
Show answer & solution

Answer: (B) 3/2

The rectangular notch discharge formula involves H raised to the power 3/2.

Question 14

A triangular (V-notch) is generally preferred over a rectangular notch for measuring

  1. only very large discharges
  2. a wide range of discharges, especially small discharges, with better accuracy at low flow
  3. only pressure
  4. only velocity
Show answer & solution

Answer: (B) a wide range of discharges, especially small discharges, with better accuracy at low flow

The V-notch's shape gives better sensitivity and accuracy for small discharges than a rectangular notch.

Question 15

In a triangular notch, discharge is calculated using a formula involving the head H raised to the power of

  1. 1
  2. 3/2
  3. 5/2
  4. 2
Show answer & solution

Answer: (C) 5/2

The triangular notch discharge formula involves H raised to the power 5/2, giving it its sensitivity advantage at low heads.

Question 16

Gradually varied flow in an open channel refers to flow where the depth

  1. changes abruptly over a very short distance
  2. changes gradually over a relatively long distance along the channel
  3. remains exactly constant
  4. is always at critical depth
Show answer & solution

Answer: (B) changes gradually over a relatively long distance along the channel

Gradually varied flow describes a slow, continuous change in depth along the channel, as near a weir or dam backwater.

Pipe Flow, Losses & Water Hammer

Question 17

The Darcy-Weisbach equation is used to calculate the

  1. velocity of flow directly
  2. head loss due to friction in a pipe
  3. discharge coefficient of an orifice
  4. viscosity of the fluid
Show answer & solution

Answer: (B) head loss due to friction in a pipe

The Darcy-Weisbach equation is the standard formula for friction head loss in pipe flow.

Question 18

The Darcy-Weisbach equation for head loss due to friction (hf) is given by

  1. hf = 4fLV²/2gD (or fLV²/2gD, depending on friction factor convention)
  2. hf = fLV/2gD
  3. hf = fL/DV²
  4. hf = 4fD/LV²
Show answer & solution

Answer: (A) hf = 4fLV²/2gD (or fLV²/2gD, depending on friction factor convention)

Standard Darcy-Weisbach formula relating friction head loss to length, velocity, and diameter, via the friction factor.

Question 19

In the Darcy-Weisbach equation, the friction factor f primarily depends on the

  1. length of the pipe only
  2. Reynolds number and the relative roughness of the pipe
  3. diameter of the pipe only
  4. density of the fluid only
Show answer & solution

Answer: (B) Reynolds number and the relative roughness of the pipe

Friction factor is a function of Reynolds number and relative pipe roughness, as captured on the Moody chart.

Question 20

Losses in pipe flow that occur due to sudden changes in the flow path, such as bends, valves, and fittings, are called

  1. major losses
  2. minor losses
  3. friction losses
  4. entrance losses only
Show answer & solution

Answer: (B) minor losses

Localized losses at fittings, bends, and valves are classified as minor losses, distinct from friction (major) losses.

Question 21

The major loss in a long pipeline is generally the loss due to

  1. sudden expansion
  2. friction along the length of the pipe
  3. a single bend
  4. the pipe entrance only
Show answer & solution

Answer: (B) friction along the length of the pipe

In long pipelines, friction loss along the pipe's length dominates over localized minor losses.

Question 22

Loss of head due to sudden contraction in a pipe is generally

  1. greater than the loss due to an equivalent sudden enlargement
  2. less than the loss due to an equivalent sudden enlargement, though a similar vena-contracta effect occurs
  3. exactly the same magnitude in every case
  4. zero, since contraction causes no loss
Show answer & solution

Answer: (B) less than the loss due to an equivalent sudden enlargement, though a similar vena-contracta effect occurs

Sudden contraction losses are generally smaller than sudden enlargement losses for comparable area ratios.

Question 23

When several pipes are connected in parallel between two points, the total discharge is

  1. the same in each pipe
  2. the sum of the discharges through each pipe, while the head loss is the same across each pipe
  3. always zero
  4. the same as through a single pipe of the smallest diameter
Show answer & solution

Answer: (B) the sum of the discharges through each pipe, while the head loss is the same across each pipe

Parallel pipes share a common head loss between the junctions, while discharges add to give the total flow.

Question 24

An equivalent pipe is a single pipe that

  1. is always shorter than any of the original pipes
  2. has the same discharge and head loss characteristics as a compound pipe (in series), replacing it for calculation purposes
  3. has no practical use
  4. is used only for parallel pipe systems
Show answer & solution

Answer: (B) has the same discharge and head loss characteristics as a compound pipe (in series), replacing it for calculation purposes

An equivalent pipe simplifies compound series pipe systems into a single hypothetical pipe with matching hydraulic behavior.

Question 25

The pressure rise due to water hammer is generally reduced in practice by

  1. closing valves as quickly as possible
  2. closing valves gradually (slowly) and/or providing surge tanks or air vessels
  3. increasing the pipe diameter only
  4. removing all pipe supports
Show answer & solution

Answer: (B) closing valves gradually (slowly) and/or providing surge tanks or air vessels

Gradual valve closure and pressure-relief devices like surge tanks are the standard mitigation measures for water hammer.

Question 26

A siphon is a pipe used to

  1. always increase the discharge beyond what gravity alone would provide
  2. carry water from a higher-level reservoir to a lower-level reservoir, with the pipe rising above the level of the upper reservoir at some point
  3. measure discharge only
  4. measure pressure only
Show answer & solution

Answer: (B) carry water from a higher-level reservoir to a lower-level reservoir, with the pipe rising above the level of the upper reservoir at some point

A siphon transfers liquid over an intermediate high point using atmospheric pressure and gravity.

Question 27

The maximum height to which the summit of a siphon can be raised above the supply reservoir's water level is limited mainly by the

  1. diameter of the pipe
  2. vapor pressure of the liquid, to avoid cavitation/separation of flow
  3. length of the pipe
  4. roughness of the pipe
Show answer & solution

Answer: (B) vapor pressure of the liquid, to avoid cavitation/separation of flow

If the pressure at the siphon's summit falls to the liquid's vapor pressure, flow separation (cavitation) occurs, limiting the achievable height.

Question 28

Pipe network analysis, as in a city water distribution system, is commonly carried out using methods such as the

  1. Hardy Cross method, based on iterative balancing of head losses
  2. Bernoulli's equation applied once, without iteration
  3. simple continuity equation alone
  4. Manning's formula only
Show answer & solution

Answer: (A) Hardy Cross method, based on iterative balancing of head losses

The Hardy Cross method iteratively balances flows and head losses in a looped pipe network.

Question 29

The power transmitted through a pipe is maximum when the head loss due to friction is

  1. zero
  2. equal to one-third of the total available head at the pipe inlet
  3. equal to the total available head
  4. equal to two-thirds of the total available head
Show answer & solution

Answer: (B) equal to one-third of the total available head at the pipe inlet

The classical result for maximum power transmission through a pipe occurs when friction loss equals one-third of the total head.

Question 30

Nominal pipe diameter, as opposed to actual internal diameter, is a

  1. standardized, approximate designation of pipe size, which may differ from actual dimensions
  2. always exactly equal to internal diameter
  3. irrelevant term in engineering
  4. used only for open channels
Show answer & solution

Answer: (A) standardized, approximate designation of pipe size, which may differ from actual dimensions

Nominal sizes are standardized labels that may not exactly match the pipe's true internal dimension.

Question 31

Open channel flow differs from pipe flow mainly in that open channel flow has a

  1. fully enclosed cross-section under pressure
  2. free surface exposed to atmospheric pressure
  3. no free surface at all
  4. constant velocity always
Show answer & solution

Answer: (B) free surface exposed to atmospheric pressure

The defining feature of open channel flow is a free surface at atmospheric pressure.

Question 32

The most economical (efficient) cross-section for an open channel, for a given area, is the one that

  1. has the maximum wetted perimeter
  2. has the minimum wetted perimeter, thereby minimizing frictional resistance and maximizing discharge
  3. has the maximum depth, regardless of shape
  4. is always circular in every case
Show answer & solution

Answer: (B) has the minimum wetted perimeter, thereby minimizing frictional resistance and maximizing discharge

Minimizing wetted perimeter for a given area minimizes friction, maximizing the channel's discharge capacity.

Question 33

Uniform flow in an open channel occurs when the depth, velocity, and cross-sectional area

  1. vary along the length of the channel
  2. remain constant along the length of the channel
  3. vary only with time, not with position
  4. are always zero
Show answer & solution

Answer: (B) remain constant along the length of the channel

Uniform flow has constant depth and velocity along the channel's length.

Open Channels, Vortex Flow & Similitude

Question 34

The Chezy formula for open channel flow gives the mean velocity as a function of the

  1. hydraulic mean depth and the bed slope, along with the Chezy coefficient
  2. discharge only
  3. cross-sectional area only
  4. wetted perimeter only
Show answer & solution

Answer: (A) hydraulic mean depth and the bed slope, along with the Chezy coefficient

Chezy's formula: V = C√(mi), using hydraulic mean depth m, bed slope i, and Chezy's coefficient C.

Question 35

The Manning's formula, a widely used alternative to Chezy's formula, expresses velocity in terms of the

  1. hydraulic radius, bed slope, and Manning's roughness coefficient (n)
  2. discharge and area only
  3. wetted perimeter only
  4. Reynolds number only
Show answer & solution

Answer: (A) hydraulic radius, bed slope, and Manning's roughness coefficient (n)

Manning's formula relates velocity to hydraulic radius, slope, and the roughness coefficient n.

Question 36

The hydraulic radius (or hydraulic mean depth) of an open channel is defined as the ratio of the

  1. cross-sectional area of flow to the wetted perimeter
  2. wetted perimeter to the cross-sectional area
  3. depth of flow to the width
  4. width to the depth
Show answer & solution

Answer: (A) cross-sectional area of flow to the wetted perimeter

Hydraulic radius = flow area / wetted perimeter, a key parameter in open channel flow formulas.

Question 37

The specific energy of an open channel flow at a section is defined as the total energy per unit weight measured with respect to the

  1. mean sea level
  2. channel bed at that section
  3. free surface only
  4. datum at the source of the channel
Show answer & solution

Answer: (B) channel bed at that section

Specific energy is referenced to the channel bed, combining depth and velocity head.

Question 38

The specific energy curve for a given discharge shows that, for a given specific energy (above the minimum), there are generally

  1. no possible depths of flow
  2. exactly one possible depth of flow
  3. two possible depths of flow, one subcritical and one supercritical
  4. infinite possible depths
Show answer & solution

Answer: (C) two possible depths of flow, one subcritical and one supercritical

The specific energy diagram has two branches, giving two alternate depths (subcritical and supercritical) for the same energy.

Question 39

Critical depth in open channel flow is the depth at which the specific energy for a given discharge is

  1. maximum
  2. minimum
  3. zero
  4. infinite
Show answer & solution

Answer: (B) minimum

Critical depth corresponds to the minimum point of the specific energy curve for a given discharge.

Question 40

Critical flow occurs when the Froude number is equal to

  1. 0
  2. 1
  3. less than 1 always
  4. greater than 1 always
Show answer & solution

Answer: (B) 1

Froude number = 1 defines the critical flow condition.

Question 41

Subcritical (tranquil) flow occurs when the Froude number is

  1. equal to 1
  2. less than 1
  3. greater than 1
  4. undefined
Show answer & solution

Answer: (B) less than 1

Subcritical flow, dominated by gravity relative to inertia, has Froude number below 1.

Question 42

Supercritical (rapid or shooting) flow occurs when the Froude number is

  1. equal to 1
  2. less than 1
  3. greater than 1
  4. undefined
Show answer & solution

Answer: (C) greater than 1

Supercritical flow, dominated by inertia, has Froude number above 1.

Question 43

A hydraulic jump occurs in an open channel when the flow changes abruptly from

  1. subcritical to supercritical flow
  2. supercritical to subcritical flow, with a sudden rise in depth and significant energy loss
  3. uniform to non-uniform flow with no change in flow regime
  4. laminar to turbulent flow only
Show answer & solution

Answer: (B) supercritical to subcritical flow, with a sudden rise in depth and significant energy loss

A hydraulic jump is the abrupt transition from supercritical to subcritical flow, dissipating energy.

Question 44

A hydraulic jump is often deliberately used downstream of spillways and sluice gates mainly to

  1. increase the velocity of flow further
  2. dissipate excess kinetic energy of the fast-moving flow, reducing erosion downstream
  3. increase the discharge
  4. decrease the depth of flow further
Show answer & solution

Answer: (B) dissipate excess kinetic energy of the fast-moving flow, reducing erosion downstream

Engineers use hydraulic jumps as energy dissipators to protect downstream channel beds from erosion.

Question 45

The normal depth of flow in an open channel is the depth at which

  1. flow becomes critical always
  2. uniform flow occurs for a given discharge and channel slope
  3. a hydraulic jump always forms
  4. the channel becomes most economical always
Show answer & solution

Answer: (B) uniform flow occurs for a given discharge and channel slope

Normal depth is the equilibrium depth of uniform flow for a given discharge, slope, and channel roughness.

Question 46

Backwater curves in open channel flow occur due to

  1. an obstruction (like a dam or weir) causing the depth upstream to be greater than the normal depth
  2. a channel becoming steeper than normal
  3. uniform flow conditions only
  4. an increase in channel roughness with no obstruction
Show answer & solution

Answer: (A) an obstruction (like a dam or weir) causing the depth upstream to be greater than the normal depth

An obstruction raises the water surface upstream above normal depth, producing a backwater profile.

Question 47

The bed slope of an open channel that produces uniform flow at critical depth is called the

  1. mild slope
  2. critical slope
  3. steep slope
  4. adverse slope
Show answer & solution

Answer: (B) critical slope

The critical slope is the specific slope for which uniform flow occurs exactly at the critical depth.

Question 48

The Buckingham Pi theorem states that if there are n variables in a physical phenomenon, involving m fundamental dimensions, they can be grouped into

  1. n dimensionless groups
  2. (n - m) independent dimensionless groups (pi terms)
  3. m dimensionless groups only
  4. n + m dimensionless groups
Show answer & solution

Answer: (B) (n - m) independent dimensionless groups (pi terms)

The Buckingham Pi theorem reduces n variables with m dimensions to (n-m) dimensionless pi terms.

Question 49

A model study is generally carried out to predict the behavior of a

  1. prototype (full-scale structure) using a smaller-scale physical model, based on similarity laws
  2. prototype without any need for a model
  3. model without reference to any prototype
  4. hypothetical structure with no real-world application
Show answer & solution

Answer: (A) prototype (full-scale structure) using a smaller-scale physical model, based on similarity laws

Model testing predicts full-scale prototype behavior via appropriate similarity (scaling) laws.

Question 50

Geometric similarity between a model and its prototype requires that

  1. all corresponding linear dimensions have the same ratio (scale)
  2. only the areas are proportional
  3. only the volumes are proportional
  4. the materials must be identical
Show answer & solution

Answer: (A) all corresponding linear dimensions have the same ratio (scale)

Geometric similarity means every corresponding linear dimension is scaled by the same ratio.

Practice these 50 questions interactively →