Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.
Hydraulics & Fluid Mechanics: Centrifugal Pumps, Specific Speed, NPSH and Cavitation
Civil Engineering · Hydraulics & Fluid Mechanics
38 questions, each with the answer and a worked solution. Notes on units and constants are at the top.
Practice interactively and track your score →Units and constants
SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.
Question 1
The specific speed of a centrifugal pump is a parameter used mainly to
- calculate the power lost in the bearings and the glands
- fix the casing material from the temperature of the liquid
- classify pumps and choose the impeller type for the duty
- size the suction pipe from the permissible flow velocity
Show answer & solution
Answer: (C) classify pumps and choose the impeller type for the duty
Specific speed combines speed, discharge and head to indicate whether a radial, mixed or axial-flow impeller is most suitable.
Question 2
In a Pelton wheel installation, the nozzle is typically fitted with a
- draft tube cone, regulating the exit pressure of the runner wheel
- spear (needle) valve, regulating jet area at constant velocity
- guide vane ring, regulating the swirl at the inlet to the runner
- scroll casing, regulating the flow around its periphery
Show answer & solution
Answer: (B) spear (needle) valve, regulating jet area at constant velocity
Moving the spear in or out changes the nozzle outlet area and hence discharge, while jet velocity stays almost constant.
Question 3
The casing of a centrifugal pump, which collects the liquid discharged by the impeller and guides it to the delivery pipe, is commonly of the
- divergent draft-tube type with a conical outlet
- volute (spiral) type or diffuser (vortex) type
- convergent-nozzle type with a jet outlet
- plain cylindrical type of constant cross-section
Show answer & solution
Answer: (B) volute (spiral) type or diffuser (vortex) type
Volute and vortex/diffuser casings collect the liquid leaving the impeller and convert part of its velocity head to pressure.
Question 4
The manometric head of a centrifugal pump is defined as the
- actual head developed, measured between delivery and suction flanges
- theoretical head from impeller geometry and speed, ignoring all losses
- static head between sump and delivery tank, ignoring the losses
- gauge head at the delivery flange, taken above atmosphere only
Show answer & solution
Answer: (A) actual head developed, measured between delivery and suction flanges
Manometric head is the net head actually imparted to the liquid, found from the difference of total heads at delivery and suction flanges.
Question 5
The main rotating component of a centrifugal pump, fitted with curved vanes, is called the
- casing
- delivery valve
- impeller
- diffuser
Show answer & solution
Answer: (C) impeller
The impeller is the rotating vaned member that transfers energy from the shaft to the liquid.
Question 6
Characteristic curves of a centrifugal pump, typically plotting head, power, and efficiency against discharge at a given speed, are used mainly to
- determine the foundation loads imposed on the pump base
- estimate the pipeline friction factor for the delivery main
- design the impeller vane angles from the geometry
- select a pump and predict its performance at duty points
Show answer & solution
Answer: (D) select a pump and predict its performance at duty points
Head, power and efficiency curves against discharge show how a pump behaves, so a suitable pump and duty point can be chosen.
Question 7
The overall efficiency of a centrifugal pump is the ratio of
- shaft power input to the hydraulic power delivered to the liquid
- liquid hydraulic power output to the shaft power input
- manometric head to the static head of the installation
- Euler head to the manometric head developed by the pump
Show answer & solution
Answer: (B) liquid hydraulic power output to the shaft power input
Overall efficiency = (ρ g Q Hm)/(shaft power), the product of manometric, volumetric and mechanical efficiencies.
Question 8
The volute (spiral) casing surrounding the runner of a reaction turbine is designed mainly to
- reduce the pressure abruptly before the water enters the runner
- accelerate the water steadily along the casing to build jet speed
- distribute water evenly to the guide vanes at constant velocity
- collect water leaving the runner and guide it to the tailrace
Show answer & solution
Answer: (C) distribute water evenly to the guide vanes at constant velocity
The progressively reducing cross-section keeps velocity nearly constant so each guide vane receives an equal share of flow.
Question 9
NPSH available at a pump suction must exceed the NPSH required mainly to avoid
- excessive delivery pressure at the discharge flange
- cavitation at the impeller eye on the suction side
- overheating of the motor windings from overload
- reverse rotation of the impeller on shutdown
Show answer & solution
Answer: (B) cavitation at the impeller eye on the suction side
If NPSH available exceeds NPSH required, suction pressure stays above vapour pressure and cavitation is avoided.
Question 10
A vortex (or open) type centrifugal pump impeller, without close-fitting vanes guiding flow directly to the casing, is generally preferred for
- clean cold water supply, where the highest efficiency is needed
- liquids with solids or fibres, since open passages resist clogging
- hot boiler feed water, delivered at high temperature and pressure
- very high head duties, with several stages mounted in series
Show answer & solution
Answer: (B) liquids with solids or fibres, since open passages resist clogging
Open or vortex impellers have wide passages that pass solids and fibres, at the cost of lower efficiency.
Question 11
The maximum practical suction lift of a centrifugal pump is limited mainly by
- atmospheric pressure, vapour pressure and suction line friction
- static delivery head available above the pump centreline
- rated speed of the pump and the number of impeller vanes
- diameter of the delivery pipe and the delivery valve setting
Show answer & solution
Answer: (A) atmospheric pressure, vapour pressure and suction line friction
Suction lift is capped by atmospheric pressure minus vapour pressure, friction losses and velocity head in the suction line.
Question 12
The minimum starting speed of a centrifugal pump is the speed at which the
- impeller head equals the friction loss in the delivery pipe
- delivery valve opens and discharge reaches its maximum
- pump head just equals the static head and delivery begins
- pump reaches its rated speed with the delivery valve open
Show answer & solution
Answer: (C) pump head just equals the static head and delivery begins
Below this speed the centrifugal head cannot overcome the manometric head, so no liquid is delivered; at it, delivery just begins.
Question 13
Centrifugal pumps with two impellers mounted in parallel (on separate or a common shaft, with combined discharge) are used mainly to
- reduce the minimum starting speed by sharing the static head
- increase the total discharge for a given head, since flows add
- increase the total head, since the heads of the impellers add
- raise the manometric efficiency by halving the flow per impeller
Show answer & solution
Answer: (B) increase the total discharge for a given head, since flows add
Impellers in parallel each develop the same head and deliver into a common outlet, so their discharges add.
Question 14
Wear rings fitted in a centrifugal pump casing and impeller serve mainly to
- seal the shaft against leakage of liquid out into the atmosphere
- support the weight of the rotor and carry radial loads from the shaft
- limit leakage from the high to the low pressure side, and are replaceable
- lock the impeller on the shaft and transmit the driving torque
Show answer & solution
Answer: (C) limit leakage from the high to the low pressure side, and are replaceable
Wear rings keep a tight clearance that limits recirculation from delivery to suction, and can be replaced when worn instead of the casing or impeller.
Question 15
The manometric efficiency of a centrifugal pump is defined as the ratio of the
- shaft power input to the hydraulic power delivered
- actual discharge to the theoretical impeller discharge
- Euler head to the static head of the installation
- manometric head to the Euler head of the impeller
Show answer & solution
Answer: (D) manometric head to the Euler head of the impeller
Manometric efficiency = H(manometric)/H(Euler), the fraction of the impeller head that remains after hydraulic losses.
Question 16
The head-discharge (H-Q) curve of a typical centrifugal pump generally shows the head
- staying constant up to rated discharge, then dropping sharply
- rising to a peak at rated discharge, then falling to zero
- falling as discharge increases, from its maximum at shut-off
- rising steadily with increasing discharge, from zero at shut-off
Show answer & solution
Answer: (C) falling as discharge increases, from its maximum at shut-off
A typical centrifugal pump develops its maximum head at zero discharge, and head falls as discharge rises.
Question 17
Cavitation in a centrifugal pump most commonly occurs at or near the
- volute throat, where velocity head converts to pressure
- suction side of the impeller (eye), where pressure is lowest
- delivery side of the impeller, where pressure is highest
- delivery valve, where the flow is throttled to reduce discharge
Show answer & solution
Answer: (B) suction side of the impeller (eye), where pressure is lowest
Pressure is lowest at the impeller eye and vane inlets, where it may fall to vapour pressure and cause cavitation.
Question 18
The affinity laws of a centrifugal pump state that, with speed N,
- Q ∝ N, H ∝ N³ and P ∝ N²
- Q ∝ N², H ∝ N and P ∝ N³
- Q ∝ N, H ∝ N² and P ∝ N³
- Q ∝ N², H ∝ N² and P ∝ N
Show answer & solution
Answer: (C) Q ∝ N, H ∝ N² and P ∝ N³
Velocity scales with N, so discharge scales as N, head as N², and power (Q × H) as N³.
Question 19
Mechanical seals in a centrifugal pump serve mainly to
- support the shaft radially against the impeller weight
- reduce the hydraulic thrust by balancing the impeller
- raise the delivery pressure by sealing the impeller eye
- prevent leakage of liquid along the shaft at the casing
Show answer & solution
Answer: (D) prevent leakage of liquid along the shaft at the casing
Mechanical seals close the clearance between rotating shaft and stationary casing to stop leakage.
Question 20
The mechanical efficiency of a centrifugal pump accounts for losses due to
- friction in bearings and other mechanical parts of the drive
- shock losses at entry to the impeller vanes at off-design flow
- leakage of liquid past the impeller wear rings and balance holes
- hydraulic friction and eddy losses in the casing and impeller passages
Show answer & solution
Answer: (A) friction in bearings and other mechanical parts of the drive
Mechanical efficiency is impeller power divided by shaft power, so it accounts only for losses in bearings, glands and other mechanical parts.
Question 21
The static delivery head of a centrifugal pump is the vertical distance between the
- pump centreline and liquid level in the delivery tank
- pump centreline and the liquid level in the sump below it
- pump inlet flange and its delivery flange on the casing
- liquid level in the sump and the level in the delivery tank
Show answer & solution
Answer: (A) pump centreline and liquid level in the delivery tank
Static delivery head is the vertical height from the pump centreline to the free surface of the delivery tank.
Question 22
The Pelton wheel is a classic example of
- an impulse turbine
- a reaction turbine
- an axial-flow turbine
- a mixed-flow turbine
Show answer & solution
Answer: (A) an impulse turbine
The Pelton wheel is driven by free jets at atmospheric pressure, making it the standard impulse turbine for high heads.
Question 23
Priming of a centrifugal pump refers to
- opening the delivery valve fully to reduce the starting power
- lubricating the bearings and glands before the pump starts
- filling casing and suction pipe with liquid to expel the air
- raising the speed gradually to its rated value before loading
Show answer & solution
Answer: (C) filling casing and suction pipe with liquid to expel the air
Priming removes air from the casing and suction line so the impeller can create enough vacuum to draw liquid up.
Question 24
A self-priming centrifugal pump is designed to
- expel air from its suction line automatically, without manual priming
- start with a completely empty casing, with no liquid retained at all
- deliver a constant discharge regardless of the delivery head or speed
- use a positive-displacement piston in place of the usual impeller
Show answer & solution
Answer: (A) expel air from its suction line automatically, without manual priming
A self-priming pump retains some liquid and can expel the air in its suction line itself, then continue as a normal centrifugal pump.
Question 25
In a reaction turbine, water leaving the runner passes into a
- scroll casing, collecting the flow for the penstock
- spear valve, regulating the flow at the exit
- nozzle, directing the jet into the tailrace channel
- draft tube, connecting runner exit to tailrace
Show answer & solution
Answer: (D) draft tube, connecting runner exit to tailrace
The draft tube carries water from the runner exit to the tailrace and recovers part of the exit kinetic energy.
Question 26
The shut-off head of a centrifugal pump is the head developed when the
- discharge is at its maximum, with the delivery valve fully open
- discharge is zero, with the delivery valve fully closed
- suction valve is closed and the casing is empty
- discharge is at the design value, at best efficiency
Show answer & solution
Answer: (B) discharge is zero, with the delivery valve fully closed
Shut-off head is the head at zero discharge, which is usually the maximum head of the pump.
Question 27
A pump is a hydraulic machine that converts
- mechanical energy into hydraulic energy, raising liquid head
- hydraulic energy into mechanical energy delivered at the shaft
- kinetic energy of a falling jet into electrical energy output
- electrical energy into thermal energy stored in the liquid
Show answer & solution
Answer: (A) mechanical energy into hydraulic energy, raising liquid head
A pump takes mechanical shaft power and converts it to pressure and kinetic energy of the liquid, the reverse of a turbine.
Question 28
Slip in a hydraulic coupling refers to the
- speed difference between the shafts, as a percentage of driving speed
- torque difference between the shafts, as a percentage of input torque
- ratio of driven speed to driving speed, expressed as a percentage
- fluid leakage past the seals, as a percentage of the total oil charge
Show answer & solution
Answer: (A) speed difference between the shafts, as a percentage of driving speed
Slip = (N1 - N2)/N1 × 100, the speed lag of the runner behind the impeller.
Question 29
Axial-flow (propeller-type) pump impellers are generally associated with
- high specific speed, suiting low head and large discharge
- low specific speed, suiting low head and large discharge
- intermediate specific speed, suiting very high head and small discharge
- low specific speed, suiting high head and small discharge
Show answer & solution
Answer: (A) high specific speed, suiting low head and large discharge
Axial-flow pumps have the highest specific speeds and deliver large discharges at low heads, like Kaplan turbines.
Question 30
In an ideal hydraulic coupling, the torques on the driving and driven shafts are
- larger on the driving shaft, by the ratio of the two speeds
- equal in magnitude, as a simple coupling does not multiply torque
- larger on the driven shaft, since the coupling multiplies torque
- in inverse ratio of the shaft speeds, as in a gear train
Show answer & solution
Answer: (B) equal in magnitude, as a simple coupling does not multiply torque
With no reaction member, the fluid transmits the same torque it receives, so input and output torques are equal and only speeds differ (slip).
Question 31
When two identical centrifugal pumps are operated in series, the combined head-discharge curve is obtained by
- adding the discharges of the pumps at a given head
- averaging the heads of the pumps at a given discharge
- taking the larger discharge of the pumps at each head
- adding the heads of the pumps at a given discharge
Show answer & solution
Answer: (D) adding the heads of the pumps at a given discharge
Pumps in series carry the same discharge, so at each discharge their heads add.
Question 32
When two identical centrifugal pumps are operated in parallel, the combined head-discharge curve is obtained by
- adding the discharges of the pumps at a given head
- taking the larger head of the pumps at each discharge
- averaging the discharges of the pumps at a given head
- adding the heads of the pumps at a given discharge
Show answer & solution
Answer: (A) adding the discharges of the pumps at a given head
Parallel pumps share a common head, so at each head their discharges add.
Question 33
Cavitation in hydraulic machines is minimised at the design stage by
- running the machine well above its rated discharge to flush bubbles away
- providing adequate NPSH (pumps) or Thoma factor and setting level (turbines)
- placing the machine high above the sump or tailwater to reduce the static head
- selecting the highest available speed to shorten bubble life
Show answer & solution
Answer: (B) providing adequate NPSH (pumps) or Thoma factor and setting level (turbines)
Ensuring NPSH available exceeds required for pumps, and an adequate Thoma factor and low setting for turbines, keeps pressure above vapour pressure.
Question 34
The static suction head of a centrifugal pump is the vertical distance between the
- pump centreline and liquid level in the sump, below the pump
- pump centreline and the liquid level in the delivery tank above it
- liquid level in the sump and the level in the delivery tank
- impeller outlet and the delivery flange at the pump casing
Show answer & solution
Answer: (A) pump centreline and liquid level in the sump, below the pump
Static suction head is the vertical lift from the sump liquid surface up to the pump centreline.
Question 35
Radial-flow (purely centrifugal) impellers are generally associated with
- low specific speed, suiting high head and small discharge
- intermediate specific speed, suiting very low head and large discharge
- high specific speed, suiting low head and large discharge
- very high specific speed, suiting high head and large discharge
Show answer & solution
Answer: (A) low specific speed, suiting high head and small discharge
Radial-flow impellers have the lowest specific speeds and are used for high heads with relatively small discharges.
Question 36
Multistage centrifugal pumps, having several impellers mounted in series on the same shaft, are used mainly to
- raise the discharge at a given head, as stage flows add
- develop a much higher total head, as the stage heads add
- reduce the NPSH required at the suction of the first stage
- reduce the starting torque by sharing the load among impellers
Show answer & solution
Answer: (B) develop a much higher total head, as the stage heads add
With impellers in series the same flow passes through each, and each adds its head to the total.
Question 37
In a Pelton wheel, water from the penstock is directed onto the runner buckets through a
- draft tube, which recovers part of the exit kinetic energy
- volute casing, which spreads the flow around the runner
- guide vane ring, which imparts swirl to the entering water
- nozzle, which converts pressure head into a high-speed jet
Show answer & solution
Answer: (D) nozzle, which converts pressure head into a high-speed jet
The penstock water passes through a nozzle that converts its pressure head into a high-speed jet striking the buckets.
Question 38
The operating point of a centrifugal pump in a given piping system is found at the intersection of the
- static head line and the pump shut-off head line
- pump efficiency curve and the NPSH required curve
- pump power curve and the motor torque curve
- pump H-Q curve and the system head-loss curve
Show answer & solution
Answer: (D) pump H-Q curve and the system head-loss curve
The pump delivers just the head the system needs at the intersection of the pump and system curves.