Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Centrifugal Pumps, Heads, Efficiencies and Similarity

Civil Engineering · Hydraulics & Fluid Mechanics

38 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

Overall efficiency of a centrifugal pump is the ratio of:

  1. Suction head to delivery head
  2. Actual water power output to power supplied by prime mover
  3. Volumetric discharge to theoretical discharge
  4. Impeller energy to shaft energy
Show answer & solution

Answer: (B) Actual water power output to power supplied by prime mover

ηo = water power output (wQHm) / shaft power input from prime mover.

Question 2

In SI units (Q in m³/s, H in m), the specific speed of a centrifugal pump is the speed of an imaginary geometrically similar pump which:

  1. Develops unit power under unit head
  2. Delivers 1 m³/s against 1 m head
  3. Operates at 100% volumetric efficiency
  4. Delivers 1 m³/s at unit speed
Show answer & solution

Answer: (B) Delivers 1 m³/s against 1 m head

Pump specific speed Ns = N√Q/H^(3/4) equals N when Q = 1 m³/s and H = 1 m.

Question 3

Manometric head represents:

  1. The actual total head against which a centrifugal pump must work
  2. Static suction head only
  3. Total static lift
  4. Friction losses in suction pipe only
Show answer & solution

Answer: (A) The actual total head against which a centrifugal pump must work

Manometric head is the actual total head (static plus losses plus velocity head) against which the pump works.

Question 4

When the speed of a given centrifugal pump is increased, the power required at corresponding operating points:

  1. Increases linearly in proportion to N
  2. Remains constant
  3. Decreases in proportion to 1/N
  4. Increases rapidly, in proportion to N³
Show answer & solution

Answer: (D) Increases rapidly, in proportion to N³

By the affinity laws P ∝ N³.

Question 5

Which pump is generally used to pump highly viscous fluids and oils?

  1. Jet pump
  2. Gear or screw pump (rotary positive displacement)
  3. Air-lift pump
  4. High-speed axial flow pump
Show answer & solution

Answer: (B) Gear or screw pump (rotary positive displacement)

Rotary positive displacement pumps handle viscous liquids effectively.

Question 6

Which of the following expressions gives the manometric head of a centrifugal pump?

  1. Work done per unit weight of water by the impeller, with no losses deducted
  2. Suction lift + suction friction loss + delivery lift + delivery friction loss + delivery velocity head
  3. Suction lift + delivery lift only, with all losses ignored
  4. Delivery lift minus suction lift plus the suction friction loss only
Show answer & solution

Answer: (B) Suction lift + suction friction loss + delivery lift + delivery friction loss + delivery velocity head

Hm = Hs + hfs + Hd + hfd + Vd²/2g, the total head the pump must actually supply.

Question 7

For geometrically similar centrifugal pumps, the head developed is proportional to:

  1. N² D²
  2. N D
  3. N² D
  4. N³ D²
Show answer & solution

Answer: (A) N² D²

H ∝ u²/g with u = πDN/60, so H ∝ N²D².

Question 8

To avoid cavitation in centrifugal pumps:

  1. Reduce the delivery pressure
  2. Run the impeller at maximum possible speed
  3. Keep the NPSH available greater than the NPSH required
  4. Raise the temperature of the liquid
Show answer & solution

Answer: (C) Keep the NPSH available greater than the NPSH required

Cavitation is avoided by keeping suction pressure high enough that NPSH available exceeds NPSH required.

Question 9

In a centrifugal pump, water enters the impeller …………… and leaves radially.

  1. Perpendicular to shaft
  2. Axially
  3. Tangentially
  4. Radially
Show answer & solution

Answer: (B) Axially

Water enters the eye of the impeller parallel to the shaft (axially) and is thrown out radially.

Question 10

Which device stores high-pressure water and releases it to hydraulic presses, cranes and lifts during peak demand?

  1. Hydraulic accumulator
  2. Siphon pipe
  3. Low-lift drainage pump
  4. Axial irrigation pump
Show answer & solution

Answer: (A) Hydraulic accumulator

A hydraulic accumulator stores energy of high-pressure water and supplies it when demand exceeds pump delivery.

Question 11

The overshot water wheels are those in which the wheel runs entirely by the …………… of water.

  1. Centrifugal force
  2. Weight
  3. Impulse
  4. Viscous drag
Show answer & solution

Answer: (B) Weight

In an overshot wheel the water enters buckets at the top and the wheel turns mainly by the weight of water in the buckets.

Question 12

The static head of a centrifugal pump installation is equal to the …………… of suction head and delivery head.

  1. Product
  2. Sum
  3. Difference
  4. Ratio
Show answer & solution

Answer: (B) Sum

Static head = static suction head + static delivery head (sum of suction lift and delivery lift).

Question 13

Discharge of a centrifugal pump is directly proportional to:

  1. Speed squared N²
  2. Inversely to N
  3. Speed N
  4. Speed cubed N³
Show answer & solution

Answer: (C) Speed N

From the affinity laws Q ∝ N.

Question 14

When the speed of a given centrifugal pump is increased, the discharge at corresponding operating points:

  1. Decreases
  2. Varies inversely with the cube of speed
  3. Increases linearly with speed
  4. Remains unchanged
Show answer & solution

Answer: (C) Increases linearly with speed

By the affinity laws Q ∝ N.

Question 15

The vane exit angle of a centrifugal pump impeller is usually kept in the range:

  1. 10° to 15°
  2. 15° to 20°
  3. 20° to 25°
  4. 25° to 30°
Show answer & solution

Answer: (C) 20° to 25°

Backward-curved vanes with exit angle about 20° to 25° are normally used for good efficiency.

Question 16

The overall efficiency of a reaction turbine is the ratio of:

  1. Runner work to jet energy
  2. Manometric head to static head
  3. Hydraulic power to friction losses
  4. Actual shaft power produced to the total energy supplied by water
Show answer & solution

Answer: (D) Actual shaft power produced to the total energy supplied by water

Overall efficiency = shaft (brake) power / water power supplied.

Question 17

Hydraulic machines are broadly classified into

  1. turbines and boilers
  2. turbines and pumps
  3. engines and pumps
  4. turbines and fans
Show answer & solution

Answer: (B) turbines and pumps

Turbines extract energy from the fluid, while pumps add energy to it, so these are the two broad classes.

Question 18

Where does the kinetic energy of water leaving the impeller of a centrifugal pump get converted into pressure energy?

  1. Inside the delivery valve
  2. At the prime mover coupling
  3. In the casing (volute or diffuser) around the impeller
  4. Inside the suction pipe
Show answer & solution

Answer: (C) In the casing (volute or diffuser) around the impeller

The expanding passages of the volute or diffuser reduce velocity and raise pressure.

Question 19

A centrifugal pump will start delivering liquid only when pressure rise in the impeller is equal to:

  1. Static head
  2. Velocity head
  3. Kinetic head
  4. Manometric head
Show answer & solution

Answer: (D) Manometric head

Unless the pressure rise in the impeller equals the manometric head, the water cannot overcome it and no delivery occurs.

Question 20

The efficiency of a centrifugal pump is maximum when the impeller blades are bent:

  1. Forward
  2. Radially straight
  3. At 90 degrees
  4. Backward
Show answer & solution

Answer: (D) Backward

Backward-curved vanes give the highest efficiency and stable operation, whereas forward-curved vanes have high exit velocity and low efficiency.

Question 21

Delivery head of a centrifugal pump varies with speed as:

  1. Directly proportional to N²
  2. Independent of speed
  3. Directly proportional to N
  4. Inversely proportional to N
Show answer & solution

Answer: (A) Directly proportional to N²

From the affinity laws H ∝ N².

Question 22

For geometrically similar centrifugal pumps running at the same speed, the power required is proportional to the impeller diameter D raised to the power:

  1. 2 (D²)
  2. 3 (D³)
  3. 4 (D⁴)
  4. 5 (D⁵)
Show answer & solution

Answer: (D) 5 (D⁵)

P ∝ ρ N³ D⁵ from similitude, so at constant N it varies as D⁵.

Question 23

If the net positive suction head (NPSH) requirement of a centrifugal pump is not satisfied:

  1. Cavitation occurs, causing noise, pitting and a fall in head
  2. Delivery head rises above the design value
  3. Pump efficiency improves as vapour reduces friction
  4. Suction pressure rises above atmospheric
Show answer & solution

Answer: (A) Cavitation occurs, causing noise, pitting and a fall in head

When NPSH available is below NPSH required, local pressure drops to vapour pressure and cavitation occurs.

Question 24

Delivery head of a centrifugal pump is proportional to impeller diameter according to:

  1. Square of diameter D²
  2. Cube of diameter D³
  3. Linear diameter D
  4. Inversely proportional to D
Show answer & solution

Answer: (A) Square of diameter D²

For similar pumps at the same speed H ∝ N²D², so H ∝ D².

Question 25

A centrifugal pump with specific speed between 80 and 160 r.p.m. is classified as:

  1. Slow speed with radial flow at outlet
  2. Medium speed with radial flow at outlet
  3. High speed with mixed flow at outlet
  4. High speed with purely axial flow at outlet
Show answer & solution

Answer: (C) High speed with mixed flow at outlet

Pumps with Ns 80 to 160 r.p.m. are high speed pumps with mixed flow.

Question 26

When the rotational speed of a centrifugal pump increases, its NPSH requirement:

  1. Drops to zero
  2. Remains constant
  3. Decreases
  4. Increases
Show answer & solution

Answer: (D) Increases

Higher speed raises the velocities and pressure drops at the impeller eye, so NPSH required increases (roughly with N²).

Question 27

Mechanical efficiency of a centrifugal pump is the ratio of:

  1. Water power at delivery to power available at the impeller
  2. Power available at the impeller to power supplied to the pump shaft by the prime mover
  3. Manometric head to the head imparted by the impeller
  4. Actual work done by the pump to energy supplied by the prime mover
Show answer & solution

Answer: (B) Power available at the impeller to power supplied to the pump shaft by the prime mover

ηm = power at impeller / shaft power; it accounts for bearing and gland losses.

Question 28

In a centrifugal pump installation, the regulating delivery valve is provided on the:

  1. Delivery pipe
  2. Suction pipe
  3. Casing housing
  4. Impeller eye
Show answer & solution

Answer: (A) Delivery pipe

The regulating (delivery) valve is fitted on the delivery pipe; it is closed when starting the pump to reduce starting torque.

Question 29

Power required to drive a centrifugal pump is proportional to speed N according to:

  1. N^(1/2)
  2. N³
  3. N
  4. N²
Show answer & solution

Answer: (B) N³

From the affinity laws P ∝ N³.

Question 30

The specific speed (Ns = N√Q/H^(3/4), Q in m³/s, H in m) of a centrifugal pump delivering 750 litres/sec against 15 m head at 725 r.p.m. is approximately:

  1. 24.8 r.p.m.
  2. 48.2 r.p.m.
  3. 82.4 r.p.m.
  4. 248 r.p.m.
Show answer & solution

Answer: (C) 82.4 r.p.m.

Ns = 725 × √0.75 / 15^0.75 = 627.9/7.62 = 82.4 r.p.m.

Question 31

The ratio of quantity of liquid discharged per second to the quantity passing through the impeller is known as:

  1. Volumetric efficiency
  2. Mechanical efficiency
  3. Manometric efficiency
  4. Overall efficiency
Show answer & solution

Answer: (A) Volumetric efficiency

Volumetric efficiency = discharge delivered / discharge passing through impeller (leakage losses).

Question 32

In a mixed flow centrifugal pump, flow through the impeller is a combination of:

  1. Laminar and turbulent flows
  2. Tangential and rotational flows
  3. Radial and axial flows
  4. Gravitational and pressure flows
Show answer & solution

Answer: (C) Radial and axial flows

A mixed flow impeller discharges water with both radial and axial velocity components.

Question 33

Which of the following casings is commonly used to house a centrifugal pump impeller?

  1. A volute casing whose flow area increases gradually towards the delivery pipe
  2. A cylindrical casing of constant area with parallel walls
  3. An open frame with no enclosure around the impeller
  4. A converging nozzle-type casing that accelerates the flow
Show answer & solution

Answer: (A) A volute casing whose flow area increases gradually towards the delivery pipe

A volute (spiral) casing has gradually increasing area so velocity is reduced and converted to pressure.

Question 34

The specific speed (N_s) of a centrifugal pump is expressed by:

  1. (N√(Q))/(H)
  2. (N√(Q))/(H^(5/4))
  3. (N√(Q))/(H^(3/4))
  4. (N√(Q))/(H^(2/3))
Show answer & solution

Answer: (C) (N√(Q))/(H^(3/4))

Pump specific speed Ns = N√Q/H^(3/4).

Question 35

For geometrically similar centrifugal pumps running at the same speed, the discharge is directly proportional to the impeller diameter D raised to the power:

  1. 1 (D)
  2. 2 (D²)
  3. 3 (D³)
  4. 4 (D⁴)
Show answer & solution

Answer: (C) 3 (D³)

Q ∝ N D³ from similitude, so at constant N it varies as D³.

Question 36

The theoretical discharge Q of a centrifugal pump is given by (D = impeller diameter at inlet, b = impeller width at inlet, Vf = velocity of flow at inlet):

  1. π D b V_f
  2. π b V_f
  3. D b V_f
  4. π D V_f
Show answer & solution

Answer: (A) π D b V_f

Flow area = πDb (neglecting vane thickness), so Q = πDb·Vf.

Question 37

Multi-stage centrifugal pumps are utilized primarily to:

  1. Reduce prime mover torque
  2. Pump highly viscous fluids
  3. Produce high delivery heads
  4. Give high discharge volumes
Show answer & solution

Answer: (C) Produce high delivery heads

Multi-staging puts impellers in series, so heads add while discharge is the same, giving high delivery heads.

Question 38

The power required to drive a centrifugal pump is given by (w = specific weight, Q = discharge, Hm = manometric head, ηo = overall efficiency):

  1. (w · Q · H_m)/(η_o)
  2. (w · Q · η_o)/(H_m)
  3. (w · H_m)/(Q × η_o)
  4. (w · Q)/(η_o · H_m)
Show answer & solution

Answer: (A) (w · Q · H_m)/(η_o)

P = w·Q·Hm/ηo.

Practice these 38 questions interactively →