Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Fluid Properties

Civil Engineering · Hydraulics & Fluid Mechanics

40 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

An oil has a density of 800 kg/m³. Taking g = 9.81 m/s², its specific weight is

  1. 81.5 N/m³
  2. 800 N/m³
  3. 7848 N/m³
  4. 78480 N/m³
Show answer & solution

Answer: (C) 7848 N/m³

γ = ρg = 800 × 9.81 = 7848 N/m³.

Question 2

A liquid of specific gravity 0.85 occupies a tank volume of 2 m³. The mass of the liquid is

  1. 850 kg
  2. 1700 kg
  3. 2000 kg
  4. 2353 kg
Show answer & solution

Answer: (B) 1700 kg

m = SG × ρw × V = 0.85 × 1000 × 2 = 1700 kg.

Question 3

The dimensional formula of dynamic viscosity μ is

  1. ML⁻¹T⁻¹
  2. L²T⁻¹
  3. ML⁻²T⁻²
  4. MLT⁻²
Show answer & solution

Answer: (A) ML⁻¹T⁻¹

μ = τ/(du/dy) = (ML⁻¹T⁻²)/(T⁻¹) = ML⁻¹T⁻¹.

Question 4

Two large parallel plates are 2 mm apart, with oil of viscosity 0.05 Pa·s between them. The upper plate moves at 1.5 m/s while the lower plate is fixed. Assuming a linear velocity profile, the shear stress in the oil is

  1. 0.0375 Pa
  2. 3.75 Pa
  3. 18.75 Pa
  4. 37.5 Pa
Show answer & solution

Answer: (D) 37.5 Pa

τ = μ(V/h) = 0.05 × 1.5/0.002 = 37.5 Pa.

Question 5

The dimensional formula of surface tension σ (force per unit length) is

  1. MLT⁻²
  2. ML⁻¹T⁻²
  3. ML⁻¹T⁻¹
  4. MT⁻²
Show answer & solution

Answer: (D) MT⁻²

σ = force/length = MLT⁻²/L = MT⁻².

Question 6

The dimensional formula of specific weight γ = ρg is

  1. ML⁻¹T⁻²
  2. MLT⁻²
  3. ML⁻³
  4. ML⁻²T⁻²
Show answer & solution

Answer: (D) ML⁻²T⁻²

γ = ρg = (ML⁻³)(LT⁻²) = ML⁻²T⁻².

Question 7

A fluid that does not flow until the applied shear stress exceeds a certain yield value, and then shows a linear stress–strain-rate relation, is called a

  1. dilatant fluid
  2. Newtonian fluid
  3. Bingham plastic
  4. pseudoplastic fluid
Show answer & solution

Answer: (C) Bingham plastic

A Bingham plastic needs a minimum (yield) shear stress before flow starts, e.g. toothpaste or sewage sludge.

Question 8

In a pseudoplastic (shear-thinning) fluid, the apparent viscosity

  1. increases as the shear rate increases
  2. decreases as the shear rate increases
  3. becomes zero at very low shear rates
  4. remains constant at all shear rates
Show answer & solution

Answer: (B) decreases as the shear rate increases

Pseudoplastic fluids such as paint and blood thin out with increasing velocity gradient.

Question 9

A flat plate of area 0.5 m² is pulled at 0.25 m/s over a fixed surface, the gap of 5 mm being filled with oil of viscosity 0.4 Pa·s (linear velocity profile). The force required is

  1. 10 N
  2. 20 N
  3. 100 N
  4. 200 N
Show answer & solution

Answer: (A) 10 N

F = τA = μ(V/h)A = 0.4 × (0.25/0.005) × 0.5 = 10 N.

Question 10

An oil has dynamic viscosity 0.06 Pa·s and specific gravity 1.2. Its kinematic viscosity is

  1. 5 × 10⁻⁵ m²/s
  2. 6 × 10⁻⁵ m²/s
  3. 7.2 × 10¹ m²/s
  4. 2 × 10⁴ m²/s
Show answer & solution

Answer: (A) 5 × 10⁻⁵ m²/s

ν = μ/ρ = 0.06/1200 = 5.0 × 10⁻⁵ m²/s.

Question 11

Clean water (σ = 0.0728 N/m, contact angle 0°) rises in a glass tube of 2 mm internal diameter. Taking ρ = 1000 kg/m³ and g = 9.81 m/s², the capillary rise is approximately

  1. 3.7 mm
  2. 7.4 mm
  3. 14.8 mm
  4. 29.7 mm
Show answer & solution

Answer: (C) 14.8 mm

h = 4σcosθ/(ρgd) = 4 × 0.0728/(1000 × 9.81 × 0.002) = 0.01484 m ≈ 14.8 mm.

Question 12

Mercury (σ = 0.48 N/m, contact angle 130°, ρ = 13 600 kg/m³) is in contact with a glass tube of 3 mm internal diameter. Taking g = 9.81 m/s², the magnitude of the capillary depression is approximately

  1. 0.77 mm
  2. 1.54 mm
  3. 3.08 mm
  4. 4.80 mm
Show answer & solution

Answer: (C) 3.08 mm

h = 4σcosθ/(ρgd) = 4 × 0.48 × 0.643/(13 600 × 9.81 × 0.003) ≈ 3.08 mm, a depression because cosθ is negative.

Question 13

A spherical water droplet of diameter 0.4 mm has surface tension 0.072 N/m. The excess pressure inside the droplet over the outside pressure is

  1. 360 Pa
  2. 720 Pa
  3. 1440 Pa
  4. 2880 Pa
Show answer & solution

Answer: (B) 720 Pa

Δp = 4σ/d = 4 × 0.072/0.0004 = 720 Pa.

Question 14

A dilatant (shear-thickening) fluid is one in which the apparent viscosity

  1. is independent of the shear rate
  2. decreases with time at constant shear
  3. increases as the shear rate increases
  4. decreases as the shear rate increases
Show answer & solution

Answer: (C) increases as the shear rate increases

Dilatant fluids such as wet sand slurries and starch suspensions stiffen under rapid shearing.

Question 15

A soap bubble of diameter 20 mm has a surface tension of 0.025 N/m at each of its two film surfaces. The excess pressure inside the bubble is

  1. 2.5 Pa
  2. 5 Pa
  3. 10 Pa
  4. 20 Pa
Show answer & solution

Answer: (C) 10 Pa

For a soap bubble Δp = 8σ/d = 8 × 0.025/0.02 = 10 Pa.

Question 16

Cavitation in a flowing liquid begins when

  1. the local gauge pressure becomes zero
  2. the flow velocity reaches the speed of sound
  3. the Reynolds number exceeds 4000
  4. the local absolute pressure falls to the vapour pressure
Show answer & solution

Answer: (D) the local absolute pressure falls to the vapour pressure

Vapour bubbles form where the absolute pressure drops to the liquid's vapour pressure at that temperature.

Question 17

The vapour pressure of a pure liquid

  1. is independent of temperature
  2. falls as its temperature rises
  3. depends only on the container shape
  4. rises as its temperature rises
Show answer & solution

Answer: (D) rises as its temperature rises

Higher temperature gives molecules more energy to escape, so vapour pressure increases.

Question 18

Water boils at a lower temperature at high altitude because

  1. atmospheric pressure is lower, so vapour pressure equals it sooner
  2. surface tension of water increases with height
  3. the density of water decreases with altitude
  4. gravity is smaller, so water molecules escape sooner
Show answer & solution

Answer: (A) atmospheric pressure is lower, so vapour pressure equals it sooner

Boiling occurs when vapour pressure equals the ambient pressure, which is smaller at altitude.

Question 19

In a centrifugal pump, cavitation is most likely to start at

  1. the pressure gauge connection
  2. the delivery pipe near the valve
  3. the outer rim of the volute casing
  4. the impeller eye on the suction side
Show answer & solution

Answer: (D) the impeller eye on the suction side

Pressure is lowest at the suction-side impeller inlet, where vapour bubbles first form.

Question 20

Unlike in gases, the viscosity of liquids is mainly due to

  1. adhesion to the container walls
  2. molecular momentum exchange between layers, as in gases
  3. cohesion between molecules
  4. the compressibility of the liquid
Show answer & solution

Answer: (C) cohesion between molecules

Intermolecular cohesion dominates in liquids, whereas molecular momentum transfer dominates in gases.

Question 21

As the temperature of a liquid increases, its surface tension generally

  1. remains unchanged
  2. increases
  3. decreases
  4. first doubles and then halves
Show answer & solution

Answer: (C) decreases

Cohesive forces weaken with heating, so surface tension falls and becomes zero at the critical point.

Question 22

The pressure on a liquid is increased by 15 MPa and its volume decreases by 0.6%. The bulk modulus of the liquid is

  1. 25 MPa
  2. 90 MPa
  3. 250 MPa
  4. 2 500 MPa
Show answer & solution

Answer: (D) 2 500 MPa

K = Δp/(ΔV/V) = 15/0.006 = 2500 MPa.

Question 23

For a liquid droplet in air, the excess internal pressure is

  1. independent of the droplet diameter
  2. inversely proportional to the droplet diameter
  3. directly proportional to the droplet diameter
  4. proportional to the square of the diameter
Show answer & solution

Answer: (B) inversely proportional to the droplet diameter

Δp = 4σ/d, so smaller droplets have a higher internal pressure.

Question 24

A liquid that wets a solid surface forms a contact angle which is

  1. less than 90°
  2. greater than 90°
  3. equal to 90° in all cases
  4. exactly 180°
Show answer & solution

Answer: (A) less than 90°

Adhesion exceeds cohesion for wetting liquids, giving θ < 90° and capillary rise.

Question 25

If the diameter of a clean glass capillary tube dipped in water is halved, the capillary rise becomes

  1. half its original value
  2. twice its original value
  3. unchanged
  4. four times its original value
Show answer & solution

Answer: (B) twice its original value

h = 4σcosθ/(ρgd) is inversely proportional to d, so halving d doubles h.

Question 26

When a small amount of detergent is added to water in which a capillary tube is dipped, the capillary rise

  1. increases, because the density is reduced
  2. decreases, because the surface tension is reduced
  3. remains the same, because the contact angle is fixed
  4. increases, because the viscosity is reduced
Show answer & solution

Answer: (B) decreases, because the surface tension is reduced

Detergent lowers σ, and since h is proportional to σ the rise decreases.

Question 27

Water attains its maximum density at a temperature of approximately

  1. 4 °C
  2. 0 °C
  3. 100 °C
  4. 10 °C
Show answer & solution

Answer: (A) 4 °C

Water is densest at about 4 °C, with a density of 1000 kg/m³.

Question 28

Water with bulk modulus 2.2 GPa and volume 2 m³ is subjected to a pressure increase of 11 MPa. The decrease in volume is

  1. 0.005 m³
  2. 0.01 m³
  3. 0.1 m³
  4. 1 m³
Show answer & solution

Answer: (B) 0.01 m³

ΔV = VΔp/K = 2 × 11/2200 = 0.01 m³.

Question 29

A liquid has a specific weight of 7.0 kN/m³. Taking g = 9.81 m/s², its specific gravity is

  1. 0.714
  2. 1.40
  3. 7.0
  4. 68.7
Show answer & solution

Answer: (A) 0.714

SG = γ/γw = 7.0/9.81 ≈ 0.714.

Question 30

Specific volume of a fluid is defined as the

  1. weight per unit volume
  2. volume per unit weight
  3. volume occupied per unit mass
  4. mass per unit volume
Show answer & solution

Answer: (C) volume occupied per unit mass

Specific volume v = 1/ρ, with units m³/kg.

Question 31

A thixotropic fluid is one whose viscosity

  1. decreases with time when sheared at a constant rate
  2. is zero at rest
  3. increases with time when sheared at a constant rate
  4. is constant with time and shear rate
Show answer & solution

Answer: (A) decreases with time when sheared at a constant rate

Thixotropy is time-dependent shear thinning, as in some paints and drilling muds.

Question 32

For an ideal gas undergoing an isothermal process, the bulk modulus of elasticity is equal to

  1. the absolute pressure p
  2. the gauge pressure only
  3. the gas density ρ
  4. the product γp of heat ratio and pressure
Show answer & solution

Answer: (A) the absolute pressure p

For pV = constant, K = −V dp/dV = p; the adiabatic value is kp.

Question 33

In a flow of a Newtonian fluid of viscosity 0.2 Pa·s, the velocity (m/s) varies with distance y (m) from a wall as u = 3y − y². The shear stress at y = 0.5 m is

  1. 0.04 Pa
  2. 0.20 Pa
  3. 0.25 Pa
  4. 0.40 Pa
Show answer & solution

Answer: (D) 0.40 Pa

du/dy = 3 − 2y = 2 s⁻¹ at y = 0.5 m, so τ = μ du/dy = 0.2 × 2 = 0.40 Pa.

Question 34

A shaft of diameter 100 mm rotates at 600 rpm inside a concentric sleeve of length 200 mm, the radial clearance of 0.2 mm being filled with oil of viscosity 0.05 Pa·s (linear velocity profile). The viscous torque on the shaft is approximately

  1. 0.62 N·m
  2. 1.23 N·m
  3. 2.47 N·m
  4. 4.93 N·m
Show answer & solution

Answer: (C) 2.47 N·m

V = πDN/60 = 3.14 m/s, τ = μV/t = 785 Pa, F = τπDL = 49.3 N, T = F·D/2 ≈ 2.47 N·m.

Question 35

The speed of sound in a liquid of bulk modulus K and density ρ is given by

  1. c = √(ρ/K)
  2. c = K/ρ
  3. c = √(Kρ)
  4. c = √(K/ρ)
Show answer & solution

Answer: (D) c = √(K/ρ)

Sound speed rises with the stiffness of the medium, c = √(K/ρ).

Question 36

Mercury is preferred as the barometer liquid mainly because it has

  1. a very high vapour pressure and a low density
  2. a very low vapour pressure and a high density
  3. a high compressibility and a high vapour pressure
  4. a high viscosity and a low surface tension
Show answer & solution

Answer: (B) a very low vapour pressure and a high density

High density keeps the column short, and negligible vapour pressure gives an almost perfect vacuum over the column.

Question 37

Water at a certain temperature has a vapour pressure of 2.3 kPa (absolute). If atmospheric pressure is 101.3 kPa, the gauge pressure at which cavitation just begins is

  1. −103.6 kPa
  2. −99.0 kPa
  3. −2.3 kPa
  4. 2.3 kPa
Show answer & solution

Answer: (B) −99.0 kPa

Cavitation starts when p(abs) = pv, so p(gauge) = 2.3 − 101.3 = −99.0 kPa.

Question 38

The temperature of a perfect gas is kept constant while its absolute pressure is doubled. Its density

  1. doubles
  2. remains unchanged
  3. halves
  4. becomes four times
Show answer & solution

Answer: (A) doubles

ρ = p/(RT), so at constant T density is proportional to absolute pressure.

Question 39

The kinematic viscosity of water at about 20 °C is approximately

  1. 1 × 10⁻⁴ m²/s
  2. 1 × 10⁻⁶ m²/s
  3. 1 × 10⁻⁹ m²/s
  4. 1 × 10⁻³ m²/s
Show answer & solution

Answer: (B) 1 × 10⁻⁶ m²/s

ν = μ/ρ ≈ 1.0 × 10⁻³/1000 = 1 × 10⁻⁶ m²/s (1 centistokes).

Question 40

A lubricating oil has a dynamic viscosity of 0.8 Pa·s. Using 1 poise = 0.1 Pa·s, its viscosity in poise is

  1. 0.008 poise
  2. 0.08 poise
  3. 0.8 poise
  4. 8 poise
Show answer & solution

Answer: (D) 8 poise

1 Pa·s = 10 poise, so 0.8 Pa·s = 8 poise.

Practice these 40 questions interactively →