Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Pipe Flow, Losses & Water Hammer

Civil Engineering · Hydraulics & Fluid Mechanics

45 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

In the Hardy Cross method of pipe network analysis, the initially assumed flows must satisfy

  1. the loop head-loss equation in every loop
  2. equal flow in every pipe of a loop
  3. equal pipe diameters around each loop
  4. continuity at every junction before the corrections are applied
Show answer & solution

Answer: (D) continuity at every junction before the corrections are applied

Initial flows satisfy continuity at nodes; the iterative loop corrections then drive ΣhL around each loop to zero while preserving continuity.

Question 2

The head loss in a sudden contraction is mainly caused by

  1. the acceleration of flow into the smaller pipe
  2. flow separation and expansion downstream of the vena contracta
  3. wall friction in the larger pipe
  4. pressure recovery at the contraction plane
Show answer & solution

Answer: (B) flow separation and expansion downstream of the vena contracta

Flow contracts to a vena contracta and then decelerates to fill the smaller pipe, causing eddies similar to a sudden enlargement.

Question 3

A valve closure that takes less than 2L/a, where L is pipe length and a the wave speed, is classified as

  1. rapid closure, giving the full Joukowsky pressure rise
  2. slow closure, with the pressure rise reduced by reflections
  3. critical closure, producing no pressure change
  4. gradual closure, treated as rigid-column flow
Show answer & solution

Answer: (A) rapid closure, giving the full Joukowsky pressure rise

If the valve is closed before the reflected relief wave returns, the full rise ρaΔV develops at the valve.

Question 4

A pipeline is 900 m long and the pressure wave speed is 1200 m/s. The critical valve closure time (time for the wave to travel to the reservoir and back) is

  1. 0.75 s
  2. 1.50 s
  3. 2.67 s
  4. 3.00 s
Show answer & solution

Answer: (B) 1.50 s

Tc = 2L/a = 2 × 900/1200 = 1.5 s.

Question 5

For Reynolds number calculations in a square duct of side a flowing full, the hydraulic diameter is

  1. a
  2. a/2
  3. a/4
  4. 2a
Show answer & solution

Answer: (A) a

Dh = 4A/P = 4a²/(4a) = a.

Question 6

If the diameter of a pipe carrying laminar flow is doubled while the pressure gradient and fluid are unchanged, the discharge becomes

  1. 4 times the original value
  2. 8 times the original value
  3. 32 times the original value
  4. 16 times the original value
Show answer & solution

Answer: (D) 16 times the original value

For laminar flow Q ∝ D⁴ at a constant pressure gradient, so Q becomes 2⁴ = 16 times.

Question 7

Water flows at 2 m/s through a 200 m long pipe of diameter 100 mm with a Darcy friction factor of 0.02. The frictional head loss is approximately

  1. 4.08 m
  2. 8.15 m
  3. 16.31 m
  4. 32.62 m
Show answer & solution

Answer: (B) 8.15 m

hf = fLV²/(2gD) = 0.02 × 200 × 2² / (2 × 9.81 × 0.1) = 8.15 m.

Question 8

Two identical pipes of diameter 0.3 m are laid in parallel with the same length and friction factor. A single pipe of the same length and friction factor that carries the same total discharge under the same head loss has a diameter of

  1. 0.300 m
  2. 0.357 m
  3. 0.378 m
  4. 0.396 m
Show answer & solution

Answer: (D) 0.396 m

Q ∝ D^(5/2), so D_eq^(5/2) = 2 × 0.3^(5/2), giving D_eq = 0.3 × 2^0.4 ≈ 0.396 m.

Question 9

In a pipeline of uniform diameter, the vertical distance between the energy grade line and the hydraulic grade line is equal to

  1. the pressure head p/γ
  2. the velocity head V²/2g
  3. the elevation head z
  4. the friction head loss hf
Show answer & solution

Answer: (B) the velocity head V²/2g

HGL = p/γ + z and EGL = p/γ + z + V²/2g, so they are separated by the velocity head V²/2g.

Question 10

In fully developed laminar flow in a circular pipe of radius R, the local velocity equals the mean velocity at a radial distance of

  1. 0.5 R from the axis
  2. 0.866 R from the axis
  3. 0.707 R from the axis
  4. 0.25 R from the axis
Show answer & solution

Answer: (C) 0.707 R from the axis

u = umax(1 − r²/R²) and V = umax/2, so 1 − r²/R² = 0.5 and r = R/√2 ≈ 0.707R.

Question 11

A pressure drop of 20 kPa occurs over a 10 m length of a 50 mm diameter pipe in steady, fully developed flow. The wall shear stress is

  1. 12.5 Pa
  2. 25.0 Pa
  3. 50.0 Pa
  4. 100.0 Pa
Show answer & solution

Answer: (B) 25.0 Pa

τ₀ = (Δp/L)(D/4) = 20000 × 0.05 / (4 × 10) = 25.0 Pa.

Question 12

Water flows at 3 m/s through a 100 mm pipe which suddenly enlarges to 200 mm diameter. The head loss at the enlargement is approximately

  1. 0.258 m
  2. 0.430 m
  3. 0.459 m
  4. 0.717 m
Show answer & solution

Answer: (A) 0.258 m

V₂ = 3 × (100/200)² = 0.75 m/s; hL = (V₁ − V₂)²/2g = 2.25²/19.62 = 0.258 m.

Question 13

The Darcy friction factor f and the Fanning friction factor f′ are related by

  1. f = 4f′
  2. f = f′/4
  3. f = 2f′
  4. f = f′
Show answer & solution

Answer: (A) f = 4f′

The Fanning factor is based on wall shear stress and dynamic head ½ρV², giving f = 4f′.

Question 14

A surge tank that consists of an inner riser pipe with small ports connected to an outer tank is called a

  1. simple surge tank
  2. restricted orifice surge tank
  3. differential (Johnson) surge tank
  4. closed pressure air chamber
Show answer & solution

Answer: (C) differential (Johnson) surge tank

The riser gives quick response to load changes while the outer tank supplies or stores the remaining volume.

Question 15

A surge tank in a hydropower conduit is generally located

  1. as close as practicable to the turbine end of the pressure conduit
  2. at the upstream end next to the intake
  3. at the midpoint of the tailrace
  4. immediately downstream of the turbine draft tube
Show answer & solution

Answer: (A) as close as practicable to the turbine end of the pressure conduit

Placing it near the turbine shortens the pipe length subject to water hammer and reduces the transient pressures.

Question 16

Water (K = 2.2 GPa) flows in a steel pipe (E = 200 GPa) of diameter 500 mm and wall thickness 10 mm. Ignoring anchoring effects, the pressure wave speed is approximately

  1. 957 m/s
  2. 1024 m/s
  3. 1191 m/s
  4. 1483 m/s
Show answer & solution

Answer: (C) 1191 m/s

a = √(K/ρ)/√(1 + KD/(Et)) = 1483/√(1 + 0.55) ≈ 1191 m/s.

Question 17

A valve on a 1200 m long pipe carrying water at 2.4 m/s is closed uniformly in 6 s (wave speed 1200 m/s). Using Michaud's approximate formula for slow closure, Δp = 2ρLV/T, the pressure rise is

  1. 240 kPa
  2. 480 kPa
  3. 960 kPa
  4. 2880 kPa
Show answer & solution

Answer: (C) 960 kPa

Closure time 6 s exceeds 2L/a = 2 s, so Δp ≈ 2ρLV/T = 2 × 1000 × 1200 × 2.4 / 6 = 960 kPa.

Question 18

In a loop of a pipe network with head loss h = rQ², pipe 1 (r = 10 s²/m⁵) carries 0.2 m³/s clockwise and pipe 2 (r = 20 s²/m⁵) carries 0.3 m³/s anticlockwise. Taking clockwise as positive, the first Hardy Cross flow correction ΔQ is

  1. −0.1750 m³/s
  2. −0.0875 m³/s
  3. +0.0875 m³/s
  4. +0.1750 m³/s
Show answer & solution

Answer: (C) +0.0875 m³/s

Σ rQ|Q| = 10(0.04) − 20(0.09) = −1.4; Σ 2r|Q| = 4 + 12 = 16; ΔQ = −(−1.4)/16 = +0.0875 m³/s.

Question 19

During water hammer, column separation in a pipeline is most likely to occur where the

  1. pressure exceeds the pipe's test pressure
  2. velocity reaches the Joukowsky value
  3. pressure falls to the vapour pressure of the water
  4. flow becomes laminar
Show answer & solution

Answer: (C) pressure falls to the vapour pressure of the water

Negative pressure waves can reduce the local pressure to the vapour pressure, forming vapour cavities that later collapse violently.

Question 20

Water (ν = 1.0 × 10⁻⁶ m²/s) flows at 7.854 L/s through a 100 mm diameter pipe. The Reynolds number of the flow is

  1. 1.0 × 10⁴
  2. 2.5 × 10⁴
  3. 5.0 × 10⁴
  4. 1.0 × 10⁵
Show answer & solution

Answer: (D) 1.0 × 10⁵

V = Q/A = 0.007854/0.007854 = 1.0 m/s; Re = VD/ν = 1.0 × 0.1 / 10⁻⁶ = 100000.

Question 21

In the three-reservoir problem, if the piezometric head at the junction equals the water level of the middle reservoir, the flow in the pipe connected to the middle reservoir is

  1. maximum
  2. equal to the discharge in the lowest pipe
  3. zero
  4. directed towards the junction
Show answer & solution

Answer: (C) zero

With no head difference between the junction and the middle reservoir, there is no driving head, so the flow in that pipe is zero.

Question 22

The Colebrook-White equation is used to estimate the friction factor mainly in the

  1. transition zone between smooth and fully rough turbulent flow
  2. laminar zone for Re below 2000
  3. critical zone between laminar and turbulent flow
  4. fully rough zone only
Show answer & solution

Answer: (A) transition zone between smooth and fully rough turbulent flow

It covers turbulent flow with both Re and ε/D influence, reducing to smooth and rough limits at extremes.

Question 23

For laminar flow in a pipe of fixed length and diameter, the head loss varies with the mean velocity V as

  1. V to the power 1.85
  2. V to the first power
  3. V to the power 2
  4. V to the power 0.5
Show answer & solution

Answer: (B) V to the first power

From Hagen-Poiseuille, hf = 32μLV/(ρgD²), which is directly proportional to V.

Question 24

Water flows at 4 m/s in the smaller pipe after a sudden contraction, where the coefficient of contraction is 0.62. The head loss due to the contraction is approximately

  1. 0.306 m
  2. 0.408 m
  3. 0.815 m
  4. 2.121 m
Show answer & solution

Answer: (A) 0.306 m

hL = (1/Cc − 1)² V²/2g = (0.613)² × 16/19.62 ≈ 0.306 m.

Question 25

For a perfectly rigid pipe, the pressure wave speed in water is equal to

  1. √(gH), the shallow-water wave speed
  2. √(2gH), the Torricelli speed
  3. √(K/ρ), the speed of sound in water
  4. √(E/ρ), the speed of sound in the pipe wall
Show answer & solution

Answer: (C) √(K/ρ), the speed of sound in water

With no pipe elasticity, a = √(K/ρ) ≈ 1450-1480 m/s for water.

Question 26

The presence of undissolved air bubbles in water flowing through a pipe causes the water hammer wave speed to

  1. increase considerably
  2. remain exactly unchanged
  3. become equal to the speed of sound in air
  4. decrease considerably
Show answer & solution

Answer: (D) decrease considerably

Air greatly increases compressibility of the mixture, which sharply lowers the effective bulk modulus and hence the wave speed.

Question 27

A reservoir discharges through a 100 m long, 200 mm diameter pipe (f = 0.02) with a sharp entrance (K = 0.5) and a submerged exit (K = 1.0). The difference in water levels is 10 m. The discharge is approximately

  1. 129.8 L/s
  2. 132.7 L/s
  3. 135.8 L/s
  4. 139.2 L/s
Show answer & solution

Answer: (A) 129.8 L/s

10 = (0.5 + 1.0 + fL/D)V²/2g = 11.5 V²/2g, so V = 4.13 m/s and Q = AV ≈ 129.8 L/s.

Question 28

A pipe is called hydraulically smooth when the

  1. roughness height is greater than the laminar sublayer thickness
  2. Reynolds number is below the critical value
  3. friction factor is equal to 64/Re
  4. laminar sublayer thickness is greater than the roughness height
Show answer & solution

Answer: (D) laminar sublayer thickness is greater than the roughness height

When the laminar sublayer covers the roughness elements, the wall behaves as smooth and f depends on Re only.

Question 29

At maximum power transmission through a pipeline, the transmission efficiency is

  1. about 50 percent
  2. about 33.3 percent
  3. about 88.9 percent
  4. about 66.7 percent
Show answer & solution

Answer: (D) about 66.7 percent

Maximum power occurs when hf = H/3, so η = (H − H/3)/H = 2/3 ≈ 66.7 percent.

Question 30

Compared with laminar flow, the turbulent velocity distribution in a pipe is

  1. more parabolic, with a lower ratio of mean to maximum velocity
  2. flatter, with a higher ratio of mean to maximum velocity
  3. uniform, with zero velocity at the wall
  4. identical, but with a smaller wall shear stress
Show answer & solution

Answer: (B) flatter, with a higher ratio of mean to maximum velocity

Turbulent mixing flattens the profile so V/umax ≈ 0.8 against 0.5 for laminar flow.

Question 31

In fully developed laminar flow, the entrance length required to develop the velocity profile in a circular pipe is approximately

  1. 10 D
  2. 4.4 Re^(1/6) D
  3. 0.5 Re D
  4. 0.06 Re D
Show answer & solution

Answer: (D) 0.06 Re D

For laminar flow Le/D ≈ 0.06 Re, which is much longer than the 20-30 D typical of turbulent flow.

Question 32

Water flowing at 3 m/s in a rigid-wall pipe is stopped instantaneously by a valve closure. If the wave speed is 1000 m/s, the pressure rise at the valve is

  1. 3.0 MPa
  2. 6.0 MPa
  3. 29.4 MPa
  4. 294.0 MPa
Show answer & solution

Answer: (A) 3.0 MPa

Joukowsky: Δp = ρaΔV = 1000 × 1000 × 3 = 3.0 × 10⁶ Pa = 3.0 MPa.

Question 33

In the laminar region of the Moody chart, the friction factor is independent of

  1. the relative roughness of the pipe wall
  2. the Reynolds number of the flow
  3. the fluid viscosity at constant velocity
  4. the pipe diameter at constant velocity
Show answer & solution

Answer: (A) the relative roughness of the pipe wall

In laminar flow f = 64/Re, so wall roughness has no influence on the friction factor.

Question 34

Pipe 1 (L = 300 m, D = 200 mm) is connected in series with pipe 2 (L = 200 m, D = 150 mm), and both have the same f. The equivalent length of a 200 mm pipe, using the relation L/D⁵ = constant, is

  1. 500.0 m
  2. 655.6 m
  3. 932.1 m
  4. 1142.8 m
Show answer & solution

Answer: (D) 1142.8 m

Le = L₁ + L₂(D₁/D₂)⁵ = 300 + 200 × (200/150)⁵ = 1142.8 m.

Question 35

Water is supplied through a pipe at 0.05 m³/s under a gross head of 120 m, and the friction head loss in the pipe is 40 m. The power available at the pipe outlet is approximately

  1. 19.62 kW
  2. 29.43 kW
  3. 39.24 kW
  4. 58.86 kW
Show answer & solution

Answer: (C) 39.24 kW

P = ρgQ(H − hf) = 1000 × 9.81 × 0.05 × (120 − 40) = 39.24 kW.

Question 36

When a pipe discharges submerged into a large reservoir, the exit loss expressed in terms of the pipe velocity V is

  1. 0.5 V²/2g, because half of the kinetic energy is recovered
  2. zero, because pressure is regained in the reservoir
  3. V²/g, because of the sudden expansion factor
  4. V²/2g, because all the kinetic energy is dissipated
Show answer & solution

Answer: (D) V²/2g, because all the kinetic energy is dissipated

The velocity falls to almost zero in the reservoir, so (V − 0)²/2g = V²/2g is lost, giving K = 1.0.

Question 37

In the Moody chart, in the fully rough (complete turbulence) zone the Darcy friction factor depends on

  1. Reynolds number only, not on relative roughness
  2. relative roughness ε/D only, not on Reynolds number
  3. both Reynolds number and fluid viscosity only
  4. pipe length and flow velocity only
Show answer & solution

Answer: (B) relative roughness ε/D only, not on Reynolds number

At high Re the laminar sublayer is thinner than the roughness, so f becomes a function of ε/D alone and the curves become horizontal.

Question 38

Two pipes of the same material and friction factor are connected in parallel between two reservoirs. The larger pipe is 200 mm in diameter and 400 m long; the smaller is 100 mm in diameter and 100 m long. Neglecting minor losses, the ratio of the discharge in the larger pipe to that in the smaller pipe is

  1. 2.00
  2. 2.83
  3. 5.66
  4. 8.00
Show answer & solution

Answer: (B) 2.83

For equal head loss, Q ∝ D^(5/2)/√L; ratio = 2^2.5 × √(100/400) = 5.66 × 0.5 = 2.83.

Question 39

A positive pressure wave generated by sudden valve closure reaching an open reservoir at the upstream end is reflected as

  1. a positive wave of double the magnitude
  2. a positive wave of the same magnitude
  3. a wave of zero magnitude
  4. a negative (relief) pressure wave of equal magnitude
Show answer & solution

Answer: (D) a negative (relief) pressure wave of equal magnitude

The reservoir holds pressure constant, so the reflected wave has opposite sign and the same magnitude.

Question 40

Oil of viscosity 0.08 Pa·s flows laminarly at 1.0 × 10⁻⁴ m³/s through a 20 mm diameter, 10 m long horizontal pipe. The pressure drop over this length is approximately

  1. 10.2 kPa
  2. 20.4 kPa
  3. 203.7 kPa
  4. 325.9 kPa
Show answer & solution

Answer: (B) 20.4 kPa

Hagen-Poiseuille: Δp = 128μLQ/(πD⁴) = 128 × 0.08 × 10 × 10⁻⁴ / (π × 0.02⁴) ≈ 20.4 kPa.

Question 41

A pipeline of gross head 90 m delivers water to a nozzle. When power in the jet is maximum, the friction loss is one-third of the gross head. Ignoring nozzle losses, the jet velocity is approximately

  1. 24.26 m/s
  2. 29.71 m/s
  3. 34.31 m/s
  4. 42.02 m/s
Show answer & solution

Answer: (C) 34.31 m/s

Head at nozzle = 90 − 30 = 60 m; Vj = √(2g × 60) = 34.31 m/s.

Question 42

The Reynolds number of laminar flow in a circular pipe is 800. The Darcy friction factor for this flow is

  1. 0.040
  2. 0.059
  3. 0.080
  4. 0.160
Show answer & solution

Answer: (C) 0.080

For laminar flow f = 64/Re = 64/800 = 0.080.

Question 43

The loss coefficient K at the entrance of a pipe with a sharp-edged, flush connection to a large reservoir is approximately

  1. 0.05
  2. 1.0
  3. 0.5
  4. 0.9
Show answer & solution

Answer: (C) 0.5

Flow contraction at the sharp edge gives a loss of about 0.5 V²/2g; a well-rounded entrance reduces it to about 0.05.

Question 44

The diameter d of a nozzle at the end of a pipe of diameter D and length L (Darcy friction factor f) that gives maximum jet power, neglecting nozzle losses, is

  1. d = (D⁵/(2fL))^(1/4)
  2. d = (D⁵/(8fL))^(1/4)
  3. d = (D⁵/(fL))^(1/4)
  4. d = (D⁴/(2fL))^(1/5)
Show answer & solution

Answer: (A) d = (D⁵/(2fL))^(1/4)

Using hf = H/3 and continuity, Vj²/V² = 2fL/D = (D/d)⁴, hence d⁴ = D⁵/(2fL).

Question 45

For a rapid valve closure, the maximum pressure rise given by the Joukowsky equation is independent of the

  1. velocity change of the water
  2. length of the pipeline
  3. density of the water
  4. wave speed in the pipe
Show answer & solution

Answer: (B) length of the pipeline

Δp = ρaΔV contains ρ, a and ΔV but not L; length only affects how long the peak pressure lasts.

Practice these 45 questions interactively →