Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Similitude and Hydraulic Devices

Civil Engineering · Hydraulics & Fluid Mechanics

24 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

Model testing of turbines before constructing the full-scale (prototype) unit is carried out mainly to

  1. estimate the silt wear rate of the prototype over its service life
  2. set the penstock thickness needed to resist water hammer pressure
  3. predict prototype performance from a small model using similarity laws
  4. determine the structural stresses in the prototype runner and shaft
Show answer & solution

Answer: (C) predict prototype performance from a small model using similarity laws

Model tests, scaled by geometric, kinematic and dynamic similarity, predict prototype efficiency and output before construction.

Question 2

A hydraulic ram is a device used to

  1. lift a large flow through a small height using an electric motor
  2. generate electricity from water falling through a small height
  3. measure the flow in a pipe by creating a pressure surge
  4. lift part of the water to a great height by water hammer
Show answer & solution

Answer: (D) lift part of the water to a great height by water hammer

A hydraulic ram uses the water hammer pressure of a larger flow falling a small height to lift a small part of it much higher.

Question 3

A hydraulic torque converter differs from a simple hydraulic coupling mainly in that it

  1. has a second rotating impeller on the driven shaft for speed increase
  2. has a stationary reaction member (stator) that multiplies torque
  3. uses a piston and cylinder to transmit torque by fluid pressure
  4. has no runner, so the torque is carried by the outer casing alone
Show answer & solution

Answer: (B) has a stationary reaction member (stator) that multiplies torque

The fixed guide vanes (stator) redirect the fluid so a reaction torque is added, making output torque larger than input torque.

Question 4

A submersible pump is designed such that

  1. pump and motor unit works fully immersed in the liquid
  2. motor stays above the liquid, driving the impeller by long shaft
  3. unit rests on the bank, with only its suction pipe immersed
  4. unit floats on the surface, drawing liquid through a hose
Show answer & solution

Answer: (A) pump and motor unit works fully immersed in the liquid

A submersible pump has a sealed motor coupled to the pump, so the whole unit is lowered into and works within the liquid.

Question 5

Kinematic similarity exists between model and prototype if both:

  1. Have identical streamline patterns and velocity ratio scaling
  2. Are equal in physical size
  3. Have identical total weight
  4. Experience identical friction losses
Show answer & solution

Answer: (A) Have identical streamline patterns and velocity ratio scaling

Kinematic similarity means similar streamlines and a constant velocity ratio.

Question 6

If the ratio of corresponding velocities at corresponding points are equal, model and prototype possess:

  1. Kinematic similarity
  2. Dynamic similarity
  3. Geometric similarity
  4. Pressure similarity
Show answer & solution

Answer: (A) Kinematic similarity

Equal ratios of velocities at corresponding points define kinematic similarity.

Question 7

The working principle of a hydraulic press, lift, and jack is based on:

  1. Pascal’s Law
  2. Bernoulli’s Equation
  3. Archimedes' Principle
  4. Newton’s Second Law
Show answer & solution

Answer: (A) Pascal’s Law

Hydraulic press, lift and jack all rely on Pascal's law (pressure transmitted equally in a confined fluid).

Question 8

In a hydraulic press, W is the load lifted by the ram of area A and P is the force applied on the plunger of area a. The ideal mechanical advantage W/P is equal to:

  1. a/A
  2. A/a
  3. A - a
  4. A × a
Show answer & solution

Answer: (B) A/a

Pressure p = P/a = W/A, so W/P = A/a.

Question 9

Geometric similarity exists between model and prototype if both:

  1. Operate under identical atmospheric pressures
  2. Are identical in shape, differing only in scale/size
  3. Have identical fluid velocities
  4. Experience identical turbulent shear stresses
Show answer & solution

Answer: (B) Are identical in shape, differing only in scale/size

Geometric similarity means identical shape, differing only in scale.

Question 10

A hydraulic crane is a device used to

  1. store the energy of pressurised liquid for later use at peak demand
  2. lift heavy loads by pressurised liquid acting on a ram
  3. raise water from a well using a rotating impeller driven by a shaft
  4. convert the energy of a falling jet into shaft power
Show answer & solution

Answer: (B) lift heavy loads by pressurised liquid acting on a ram

Pressurised liquid, usually from an accumulator, acts on a ram to lift loads, with pulleys multiplying the travel.

Question 11

Which hydraulic unit is used for transmitting increased or decreased torque smoothly to a driven shaft?

  1. Hydraulic accumulator
  2. Hydraulic torque converter
  3. Hydraulic ram
  4. Hydraulic intensifier
Show answer & solution

Answer: (B) Hydraulic torque converter

A torque converter multiplies or reduces torque; a coupling transmits the same torque.

Question 12

A hydraulic accumulator is a device used to

  1. multiply a small force into a large one with two unequal pistons
  2. increase the pressure of a liquid supply using a differential ram
  3. store pressurised liquid at low demand and release it at peak demand
  4. raise part of a flow to a greater height by water hammer action
Show answer & solution

Answer: (C) store pressurised liquid at low demand and release it at peak demand

An accumulator stores energy in a loaded ram or gas cushion during light load and supplies it during peak demand, levelling pump load.

Question 13

The capacity of a hydraulic accumulator is specified as:

  1. The maximum amount of hydraulic potential energy stored
  2. Maximum fluid volume rate
  3. Total weight of ram cylinder
  4. Maximum pipeline friction loss
Show answer & solution

Answer: (A) The maximum amount of hydraulic potential energy stored

Accumulator capacity is specified by the maximum energy stored.

Question 14

A hydraulic intensifier is a device used to:

  1. Filter hydraulic oil
  2. Reduce water hammer shock
  3. Increase the intensity of water pressure using a large volume of low-pressure supply water
  4. Measure flow velocity
Show answer & solution

Answer: (C) Increase the intensity of water pressure using a large volume of low-pressure supply water

An intensifier raises water pressure using a large volume of low-pressure water acting on a large area ram.

Question 15

If the ratios of corresponding forces acting at corresponding points are equal, they possess:

  1. Dynamic similarity
  2. Kinematic similarity
  3. Geometric similarity
  4. Mechanical equilibrium
Show answer & solution

Answer: (A) Dynamic similarity

Equal ratios of corresponding forces define dynamic similarity.

Question 16

Rotary positive-displacement pumps, such as gear pumps and screw pumps, are generally well suited for

  1. large discharges at very low pressure with clean water supply
  2. small discharges at high pressure, and viscous liquids such as oils
  3. high discharges at moderate head with thin, clean liquids
  4. liquids containing coarse abrasive solids at moderate pressure
Show answer & solution

Answer: (B) small discharges at high pressure, and viscous liquids such as oils

Gear and screw pumps give steady, fairly small flow at high pressure, and the close clearances work well with viscous oils.

Question 17

A hydraulic coupling is classified as:

  1. A flow-measuring device
  2. An impulse turbine
  3. A positive displacement pump
  4. A hydrokinetic power transmission device
Show answer & solution

Answer: (D) A hydrokinetic power transmission device

It transmits power through the kinetic energy of fluid between impeller and runner.

Question 18

A hydraulic press is a device used to:

  1. Transmit torque between shafts
  2. Store hydraulic strain energy
  3. Compress air for pneumatic tools
  4. Lift larger loads by applying a comparatively much smaller force based on Pascal's law
Show answer & solution

Answer: (D) Lift larger loads by applying a comparatively much smaller force based on Pascal's law

By Pascal's law, pressure applied on the small plunger is transmitted to the large ram, magnifying force.

Question 19

The main advantage of a hydraulic coupling, in transmitting power between an engine and a load (such as in some vehicle transmissions), is that it

  1. gives smooth, shock-free transmission and absorbs torsional vibration
  2. gives a rigid, slip-free drive that passes all torsional vibration
  3. multiplies engine torque at start-up by redirecting the fluid flow
  4. raises the driven shaft speed above engine speed at light loads
Show answer & solution

Answer: (A) gives smooth, shock-free transmission and absorbs torsional vibration

The fluid link cushions shocks and vibration and allows controlled slip, which also permits smooth starting.

Question 20

The efficiency of a hydraulic coupling, given a certain amount of unavoidable slip, is generally

  1. exactly 100%, since the torques on both shafts are equal
  2. somewhat below 100%, due to slip and fluid friction
  3. above 100% at low speeds, owing to torque multiplication
  4. equal to the slip, being lowest at high output speeds
Show answer & solution

Answer: (B) somewhat below 100%, due to slip and fluid friction

Torques are equal but output speed is below input speed, so efficiency = N2/N1 = 1 - slip, always less than 100%.

Question 21

Dynamic similarity exists between model and prototype if both:

  1. Have the same physical size
  2. Are geometrically and kinematically similar and have equal ratios of corresponding forces
  3. Experience equal total weight and equal pressure
  4. Operate at the same rotational r.p.m.
Show answer & solution

Answer: (B) Are geometrically and kinematically similar and have equal ratios of corresponding forces

Dynamic similarity requires geometric and kinematic similarity plus constant force ratios.

Question 22

If the ratio of all corresponding linear dimensions between model and prototype are equal, they possess:

  1. Dynamic similarity
  2. Kinematic similarity
  3. Geometric similarity
  4. Thermal similarity
Show answer & solution

Answer: (C) Geometric similarity

Equal ratios of corresponding linear dimensions define geometric similarity.

Question 23

A hydraulic press is a device that works on the principle of

  1. the continuity equation, with equal mass flow at all sections
  2. Archimedes' principle, with buoyancy equal to the weight displaced
  3. Pascal's law, with fluid pressure transmitted equally in all directions
  4. Bernoulli's theorem, with total energy constant along a streamline
Show answer & solution

Answer: (C) Pascal's law, with fluid pressure transmitted equally in all directions

Pascal's law states that pressure applied to a confined fluid is transmitted undiminished, so a small piston force produces a large force on the big piston.

Question 24

A hydraulic accumulator is a device used to store ………… energy to supply machinery during peak demand.

  1. Thermal
  2. Electrical
  3. Pressure (potential)
  4. Kinetic
Show answer & solution

Answer: (C) Pressure (potential)

An accumulator stores water under pressure, i.e. potential energy, for release during peak demand.

Practice these 24 questions interactively →