Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Hydraulics & Fluid Mechanics: Draft Tubes, Governing and Turbine Performance

Civil Engineering · Hydraulics & Fluid Mechanics

37 questions, each with the answer and a worked solution. Notes on units and constants are at the top.

Practice interactively and track your score →

Units and constants

SI units throughout. Take g = 9.81 m/s² and the density of water as 1000 kg/m³ wherever a value is needed.

Question 1

The unit speed of a turbine runner (N_u) is given by:

  1. N / H²
  2. N / √(H)
  3. N / H
  4. N / H^(3/2)
Show answer & solution

Answer: (B) N / √(H)

Unit speed Nu = N/√H, since N ∝ √H for a given turbine.

Question 2

A surge tank on a long penstock of a reaction turbine plant is mainly provided to

  1. absorb pressure surges caused by flow changes in governing
  2. cool the water before it reaches the runner
  3. settle silt before the water reaches the penstock
  4. increase the net head at the runner
Show answer & solution

Answer: (A) absorb pressure surges caused by flow changes in governing

It reflects water hammer waves and supplies or stores water during rapid load changes, protecting the penstock.

Question 3

The efficiency of a draft tube is the ratio of

  1. actual pressure head recovered to kinetic head at tube inlet
  2. kinetic head at outlet to kinetic head at inlet
  3. net head to gross head across the tube
  4. head loss in the tube to kinetic head at inlet
Show answer & solution

Answer: (A) actual pressure head recovered to kinetic head at tube inlet

Draft tube efficiency compares the actual conversion of kinetic head into pressure head with the available inlet kinetic head.

Question 4

The speed of an imaginary turbine, identical with a given turbine, which will develop a unit power under a unit head is known as:

  1. Synchronous speed
  2. Specific speed
  3. Unit speed
  4. Normal speed
Show answer & solution

Answer: (B) Specific speed

Specific speed is the speed of a geometrically similar turbine that develops unit power under unit head.

Question 5

The vacuum at the draft tube inlet is limited mainly to avoid

  1. water hammer in the penstock
  2. overspeeding of the runner
  3. cavitation damage to the runner and tube
  4. silt deposition in the tailrace
Show answer & solution

Answer: (C) cavitation damage to the runner and tube

If the absolute pressure falls to the vapour pressure the water vaporises, causing cavitation damage.

Question 6

Runaway speed of a turbine is the

  1. speed at which the unit synchronises with the grid at part load
  2. highest speed allowed by the governor during normal rated operation
  3. maximum speed reached if load is removed and governor fails to act
  4. speed of maximum efficiency under rated head and full gate opening
Show answer & solution

Answer: (C) maximum speed reached if load is removed and governor fails to act

If load is thrown off and the governor does not close the gates in time, the runner accelerates to its maximum (runaway) speed, a fixed multiple of normal speed for a given head.

Question 7

Losses in a draft tube are kept small by making it

  1. expand suddenly just after the runner
  2. gradually diverge with a small cone angle
  3. keep a uniform cross-section throughout
  4. be short with a large cone angle
Show answer & solution

Answer: (B) gradually diverge with a small cone angle

Gradual diffusion decelerates the flow smoothly, avoiding separation and eddy losses.

Question 8

Selection of a suitable turbine for a given hydropower site depends primarily on the available

  1. tailrace channel length and bed slope, which fix the runner type
  2. head and discharge (or power), which fix the specific speed
  3. penstock material and wall thickness, which fix the runner type
  4. generator voltage and grid frequency, which fix the runner type
Show answer & solution

Answer: (B) head and discharge (or power), which fix the specific speed

Head and discharge (or power) give the specific speed, which indicates whether a Pelton, Francis or Kaplan turbine suits the site.

Question 9

If the electrical load on a turbine-generator suddenly falls and the governor does not respond, the speed will

  1. rise, because less power is drawn for the same flow
  2. fall sharply, because the load torque drops
  3. stay constant, because of runner inertia
  4. oscillate about a steady mean value
Show answer & solution

Answer: (A) rise, because less power is drawn for the same flow

Water power input exceeds the reduced load, so the surplus accelerates the rotor, causing overspeed.

Question 10

If V_1 and V_2 are velocities of water at inlet and outlet of a draft tube respectively, the theoretical efficiency of the draft tube is:

  1. (V_1² - V_2²)/(V_1²)
  2. (V_1 - V_2)/(V_1)
  3. (V_1²)/(V_1² - V_2²)
  4. (V_1)/(V_1 - V_2)
Show answer & solution

Answer: (A) (V_1² - V_2²)/(V_1²)

Ideal draft tube efficiency = (V1²/2g - V2²/2g)/(V1²/2g) = (V1² - V2²)/V1², i.e. the fraction of inlet kinetic head recovered.

Question 11

The unit power developed by a turbine (P_u) is expressed as:

  1. P / √(H)
  2. P / H²
  3. P / H
  4. P / H^(3/2)
Show answer & solution

Answer: (D) P / H^(3/2)

Unit power Pu = P/H^(3/2), obtained from P ∝ H^(3/2) at constant diameter.

Question 12

The unit discharge through a turbine (Q_u) is given by:

  1. Q / H^(3/2)
  2. Q / H²
  3. Q / H
  4. Q / √(H)
Show answer & solution

Answer: (D) Q / √(H)

Unit discharge Qu = Q/√H, since Q ∝ √H for a given turbine.

Question 13

Pitting on the surface of a turbine runner after long operation is typically evidence of

  1. cavitation damage from repeated collapse of vapour bubbles
  2. galvanic corrosion between dissimilar metals in the runner
  3. thermal stress from uneven heating of the runner in service
  4. fatigue cracking caused by shaft vibration at the runner hub
Show answer & solution

Answer: (A) cavitation damage from repeated collapse of vapour bubbles

Collapsing vapour bubbles produce high local impact pressures that pit the metal surface, the classic sign of cavitation.

Question 14

The runaway speed of a hydraulic turbine is defined as the speed:

  1. At which the runner vibrates with critical amplitude
  2. Reached when the turbine runs freely without load, with gates fully open, under the maximum head
  3. Reached at full load under normal design head
  4. Equal to the synchronous speed of the connected grid
Show answer & solution

Answer: (B) Reached when the turbine runs freely without load, with gates fully open, under the maximum head

Runaway speed is the maximum speed attained if the load is suddenly thrown off and the governor fails, with gates fully open under maximum head.

Question 15

To limit excavation depth in large plants, the draft tube commonly used is the

  1. straight cylindrical type of uniform bore
  2. elbow type with a diverging outlet
  3. Moody spreading type
  4. straight conical type with a small cone angle
Show answer & solution

Answer: (B) elbow type with a diverging outlet

The bend turns the flow horizontally, reducing excavation depth while the diverging outlet keeps recovery efficient.

Question 16

Guide vanes in a reaction turbine mainly serve to

  1. recover the kinetic energy at the runner exit
  2. support the runner weight on the main shaft
  3. convert the whole head into jet velocity as a nozzle
  4. regulate flow and set the entry angle to the runner
Show answer & solution

Answer: (D) regulate flow and set the entry angle to the runner

Wicket gates vary the flow area to control discharge and set the entry angle for shock-free flow.

Question 17

Cavitation in a reaction turbine most commonly occurs near the

  1. runner inlet and guide vane ring, where the pressure is highest
  2. penstock intake and trash rack, where static head is greatest
  3. runner exit and draft tube inlet, where pressure is lowest
  4. spiral casing entry, where the pressure head is greatest
Show answer & solution

Answer: (C) runner exit and draft tube inlet, where pressure is lowest

Pressure is lowest at the runner exit and draft tube inlet, where it can fall to the vapour pressure and form bubbles.

Question 18

In a main characteristic (constant head) curve, the quantities are plotted against

  1. speed, at constant head
  2. guide vane opening, at constant speed
  3. net head, at constant speed
  4. discharge, at constant efficiency
Show answer & solution

Answer: (A) speed, at constant head

Main characteristic curves give discharge, power and efficiency against speed (unit speed) at constant head for various gate openings.

Question 19

One practical measure to reduce cavitation risk in an existing turbine installation, where the runner is set too high above the tailrace, is to

  1. raise the runner setting to reduce the suction head at the draft tube
  2. lower the tailrace level to increase the static suction head available
  3. increase the runner speed to cut the exit velocity head at part load
  4. lower the runner setting relative to tailrace to raise the exit pressure
Show answer & solution

Answer: (D) lower the runner setting relative to tailrace to raise the exit pressure

Lowering the runner relative to tailwater increases the absolute pressure at the runner exit, raising sigma and reducing cavitation.

Question 20

The main advantage of a draft tube is that it lets the runner be set

  1. above tailrace level without losing that head
  2. below tailrace level to avoid cavitation
  3. close to the spiral casing outlet
  4. at the same level as the penstock
Show answer & solution

Answer: (A) above tailrace level without losing that head

The suction created by the draft tube lets the runner be placed above the tailrace while the head down to the tailrace is still utilised.

Question 21

Cavitation in a hydraulic machine is mainly caused by:

  1. Local static pressure falling below the vapour pressure of the liquid
  2. Excessive oil viscosity
  3. Excessive length of the delivery pipe
  4. High mechanical friction in the bearings
Show answer & solution

Answer: (A) Local static pressure falling below the vapour pressure of the liquid

Cavitation occurs when the local absolute pressure drops to the vapour pressure, forming vapour bubbles that later collapse.

Question 22

A draft tube connects the

  1. penstock to the spiral casing
  2. surge tank to the penstock
  3. runner outlet to the tailrace
  4. guide vanes to the runner inlet
Show answer & solution

Answer: (C) runner outlet to the tailrace

It is the conduit that carries water from the runner exit down to the tailrace.

Question 23

Characteristic curves of a turbine are mainly used to

  1. find the friction factor of the penstock
  2. compute the shaft stress in the runner
  3. predict performance at varying head and speed
  4. select the surge tank diameter
Show answer & solution

Answer: (C) predict performance at varying head and speed

Curves from model or prototype tests show performance over the working range, guiding selection and operation.

Question 24

The point on a pump's characteristic curve where the pump operates most efficiently is called the

  1. maximum discharge point
  2. zero-discharge point
  3. maximum power point
  4. best efficiency point
Show answer & solution

Answer: (D) best efficiency point

At the best efficiency point (BEP) the efficiency curve peaks, so the pump operates with minimum losses.

Question 25

A turbine develops 10,000 kW under a head of 25 m at 135 r.p.m. Its specific speed (Ns = N√P/H^(5/4), P in kW) is approximately:

  1. 175.4 r.p.m.
  2. 215.5 r.p.m.
  3. 241.5 r.p.m.
  4. 275.4 r.p.m.
Show answer & solution

Answer: (C) 241.5 r.p.m.

Ns = 135 × √10000 / 25^1.25 = 13500/55.9 = 241.5 r.p.m.

Question 26

Routine maintenance of hydraulic pumps and turbines typically includes checks on

  1. bearing lubrication, seal condition and checks for cavitation pitting
  2. motor insulation tests alone, with no inspection of mechanical parts
  3. periodic re-machining of the penstock to restore its original bore
  4. replacement of the impeller each month, regardless of its actual wear
Show answer & solution

Answer: (A) bearing lubrication, seal condition and checks for cavitation pitting

Routine maintenance covers bearings, seals or packing, and inspection of wetted parts for cavitation damage and wear.

Question 27

Which of the following statements about the draft tube of a reaction turbine is correct?

  1. It lets the runner be set above tailrace level and recovers part of the outlet kinetic energy as pressure head
  2. It converts the pressure head at the runner inlet into kinetic energy before the water enters
  3. It regulates the flow entering the runner by varying the opening of the guide vanes
  4. It is used only in impulse turbines to stop the jet from splashing on the buckets
Show answer & solution

Answer: (A) It lets the runner be set above tailrace level and recovers part of the outlet kinetic energy as pressure head

The gradually diverging draft tube keeps the runner flowing full, allows the runner to be placed above tailrace and converts outlet kinetic head into pressure, giving a suction head below the runner.

Question 28

Unit quantities of a turbine refer to its values under a

  1. discharge of 1 m³/s
  2. power of 1 kW
  3. head of 1 m
  4. speed of 1 rpm
Show answer & solution

Answer: (C) head of 1 m

Unit speed, discharge and power are the values for a similar turbine working under 1 m head.

Question 29

Kaplan turbines are particularly prone to cavitation because they

  1. run in air with a fixed atmospheric exit pressure
  2. operate at very high heads with large pressure drops
  3. have high specific speed and a small cavitation margin
  4. have low specific speed and widely spaced blades
Show answer & solution

Answer: (C) have high specific speed and a small cavitation margin

High specific speed means a high critical sigma, so the available margin is small at the low heads where Kaplans operate.

Question 30

The specific speed of a hydraulic turbine depends upon:

  1. Discharge and power developed only
  2. Pipeline diameter and friction factor
  3. Speed, power developed and effective head
  4. Speed and power developed only
Show answer & solution

Answer: (C) Speed, power developed and effective head

Ns = N√P/H^(5/4) involves speed, power and head.

Question 31

A reaction turbine set above the tailrace without a draft tube would

  1. run with the same efficiency, as exit loss is recovered
  2. gain extra head from the exit velocity
  3. lose only the head to tailrace, recovering exit energy
  4. lose the exit kinetic energy and the head to tailrace
Show answer & solution

Answer: (D) lose the exit kinetic energy and the head to tailrace

Without a diffuser the exit kinetic energy is wasted and the head between runner and tailrace is not utilised.

Question 32

Specific speed of a turbine is the speed of a geometrically similar turbine that

  1. works at unit efficiency under unit head
  2. produces unit discharge under unit head
  3. runs at unit speed under unit head
  4. produces unit power under unit head
Show answer & solution

Answer: (D) produces unit power under unit head

Ns = N√P/H^(5/4) is the speed of a similar turbine developing 1 kW under 1 m head.

Question 33

Which of the following statements about the effects of cavitation is correct?

  1. It affects only the bearings and never the runner surfaces
  2. It raises efficiency by reducing boundary-layer friction on the blades
  3. It reduces noise because the vapour bubbles cushion the flow
  4. It causes noise, vibration, pitting of metal surfaces and a fall in efficiency
Show answer & solution

Answer: (D) It causes noise, vibration, pitting of metal surfaces and a fall in efficiency

Collapse of vapour bubbles near surfaces produces noise, vibration, pitting erosion and a drop in discharge, power and efficiency.

Question 34

If a turbine's Thoma's cavitation factor at its actual installation is less than the critical value for that turbine's design, the turbine is likely to

  1. operate safely, since a lower sigma gives a larger margin against cavitation
  2. suffer mainly from water hammer, with no real risk of cavitation
  3. operate safely at full gate, with cavitation only at part-load openings
  4. experience cavitation, since the margin over vapour pressure is too small
Show answer & solution

Answer: (D) experience cavitation, since the margin over vapour pressure is too small

Plant sigma below the critical sigma means the pressure at the runner exit is too close to vapour pressure, so cavitation is likely.

Question 35

The head available at the inlet of the turbine is known as:

  1. Friction head loss
  2. Net or effective head
  3. Gross head
  4. Static tailrace head
Show answer & solution

Answer: (B) Net or effective head

The head available at turbine inlet after losses in the penstock is the net (effective) head.

Question 36

The tailrace is the

  1. channel carrying discharged water away from the turbine
  2. pipe carrying water from the reservoir to the turbine
  3. channel feeding water to the plant intake
  4. chamber enclosing the runner and guide vanes
Show answer & solution

Answer: (A) channel carrying discharged water away from the turbine

The tailrace takes water leaving the draft tube back to the river downstream.

Question 37

The specific speed of a turbine (N_s) is given by the equation:

  1. (N√(P))/(H^(5/4))
  2. (N√(P))/(H^(3/2))
  3. (N√(P))/(H²)
  4. (N√(P))/(H)
Show answer & solution

Answer: (A) (N√(P))/(H^(5/4))

Specific speed of a turbine Ns = N√P/H^(5/4), with P in kW.

Practice these 37 questions interactively →