Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Building Materials: Lime, Gypsum & Mortars

Civil Engineering · Building Materials

21 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Gypsum plasterboard (drywall), a very widely used modern interior wall/ceiling lining material, consists essentially of a

  1. core of set gypsum plaster, sandwiched between and reinforced by facing sheets of paper (or, in some specialized products, other suitable facing materials) on both sides
  2. solid core of pure structural steel, with no gypsum or paper facing involved at all
  3. solid core of pure timber, with no gypsum content at all
  4. a purely liquid, uncured material that never actually solidifies into a usable board form
Show answer & solution

Answer: (A) core of set gypsum plaster, sandwiched between and reinforced by facing sheets of paper (or, in some specialized products, other suitable facing materials) on both sides

Plasterboard sandwiches a set gypsum core between paper (or similar) facing sheets on both sides.

Question 2

Gypsum, used as a building material mainly in the manufacture of plaster of Paris and gypsum plasterboard, is a naturally occurring mineral consisting mainly of

  1. calcium sulfate (typically as the dihydrate form, in its natural state)
  2. pure silica, with no calcium sulfate content at all
  3. pure calcium carbonate, identical in composition to ordinary limestone
  4. pure iron oxide, with no calcium or sulfate content at all
Show answer & solution

Answer: (A) calcium sulfate (typically as the dihydrate form, in its natural state)

Natural gypsum is primarily calcium sulfate dihydrate, the raw material for plaster of Paris and plasterboard.

Question 3

Plaster of Paris, manufactured by partially dehydrating (calcining) natural gypsum, is valued mainly for its

  1. very slow setting time, often taking several weeks to harden after mixing with water
  2. relatively quick setting time after mixing with water, and its ability to be cast into finely detailed decorative moldings/ornamental work, in addition to its use in some plastering and (historically) medical casting applications
  3. complete inability to set or harden under any circumstances, remaining permanently in a liquid/paste form
  4. extremely high compressive strength, exceeding that of ordinary Portland cement concrete, in every case
Show answer & solution

Answer: (B) relatively quick setting time after mixing with water, and its ability to be cast into finely detailed decorative moldings/ornamental work, in addition to its use in some plastering and (historically) medical casting applications

Plaster of Paris is valued for its quick setting and fine detail casting ability, used in plastering, molding, and historically medical casts.

Question 4

Compared to using pure fat lime, using hydraulic lime (or blending lime with a suitable pozzolanic material, such as surkhi/burnt clay, or later, with Portland cement) generally

  1. makes the resulting mortar/concrete completely unable to harden under any conditions
  2. improves the resulting mortar/concrete's ability to set and gain strength, including under damp or water-exposed conditions, compared to fat lime alone
  3. has absolutely no effect on the properties of the resulting mortar
  4. is a purely modern technique, with no historical precedent at all
Show answer & solution

Answer: (B) improves the resulting mortar/concrete's ability to set and gain strength, including under damp or water-exposed conditions, compared to fat lime alone

Adding pozzolanic material or hydraulic lime improves setting and strength under damp conditions compared to fat lime alone.

Question 5

Lime mortar, historically a very common masonry mortar (before the widespread availability of Portland cement), is generally characterized, compared to cement mortar, by

  1. considerably higher compressive strength
  2. somewhat lower compressive strength and slower hardening (particularly for fat lime mortars), but often greater flexibility/workability, historically valued particularly for older/heritage masonry repair
  3. an identical strength development curve to ordinary Portland cement mortar
  4. an inability to be used in any masonry construction whatsoever
Show answer & solution

Answer: (B) somewhat lower compressive strength and slower hardening (particularly for fat lime mortars), but often greater flexibility/workability, historically valued particularly for older/heritage masonry repair

Lime mortar is generally weaker and slower-hardening than cement mortar, but valued for flexibility in heritage masonry work.

Question 6

The hydraulic lime which resembles very much with Portland cement in its chemical composition is called

  1. feebly hydraulic lime
  2. moderately hydraulic lime
  3. eminently hydraulic lime
  4. none of these
Show answer & solution

Answer: (C) eminently hydraulic lime

Due to its high silicate and aluminate content, eminently hydraulic lime exhibits hardening and chemical properties very close to Portland cement.

Question 7

Air lime (or non-hydraulic lime) hardens mainly through the process of

  1. hydraulic reaction with water alone, with no reference to atmospheric exposure
  2. carbonation, i.e., reaction with carbon dioxide present in the atmosphere, which is a relatively slow process, especially in the interior of thick sections
  3. an instantaneous chemical reaction with sand, occurring within minutes
  4. a purely physical drying process, with no chemical reaction of any kind
Show answer & solution

Answer: (B) carbonation, i.e., reaction with carbon dioxide present in the atmosphere, which is a relatively slow process, especially in the interior of thick sections

Air lime hardens by slowly absorbing atmospheric CO2 (carbonation), a process that can be slow in thick sections.

Question 8

Eminently hydraulic lime is one in which the percentage of silica, alumina and iron oxide is

  1. 5 to 10%
  2. 10 to 25%
  3. 25 to 30%
  4. 30 to 40%
Show answer & solution

Answer: (C) 25 to 30%

Eminently hydraulic limes contain 25% to 30% clay impurities, enabling them to set underwater similar to Portland cement.

Question 9

Hydraulic lime generates _____________ heat as compared to fat lime.

  1. same
  2. less
  3. more
Show answer & solution

Answer: (B) less

Because hydraulic lime contains inert clay impurities, it slakes sluggishly and evolves considerably less heat than fat lime.

Question 10

In modern construction, lime has largely been superseded, for most general masonry mortar and plastering applications, by

  1. pure sand alone, with no binder at all
  2. Portland cement (or cement-lime blends), due to its higher strength, faster and more predictable setting, and widespread availability
  3. pure gypsum alone, with no reference to cement or lime
  4. pure clay, used exactly as in traditional lime manufacture, with no burning involved
Show answer & solution

Answer: (B) Portland cement (or cement-lime blends), due to its higher strength, faster and more predictable setting, and widespread availability

Portland cement's strength, speed, and availability have largely displaced traditional lime for most modern general construction.

Question 11

Lime plastering, a traditional finishing technique for interior and exterior walls, was historically valued partly for its

  1. extremely rapid, hard setting within minutes
  2. breathability (permeability to moisture vapor) and relative flexibility, compared to some modern cement-based plasters, making it particularly suitable for many older/traditional and heritage buildings
  3. inability to take any surface finish or decoration
  4. very high cost, well beyond that of any alternative finishing material, in every historical period
Show answer & solution

Answer: (B) breathability (permeability to moisture vapor) and relative flexibility, compared to some modern cement-based plasters, making it particularly suitable for many older/traditional and heritage buildings

Lime plaster's vapor permeability and flexibility suit older masonry, which needs to breathe and move slightly.

Question 12

Lime, as a traditional building material, is manufactured mainly by burning (calcining)

  1. pure silica sand at a high temperature
  2. limestone (calcium carbonate) at a high temperature, driving off carbon dioxide to leave calcium oxide (quicklime)
  3. pure clay, with no limestone involved
  4. steel slag, with no limestone involved
Show answer & solution

Answer: (B) limestone (calcium carbonate) at a high temperature, driving off carbon dioxide to leave calcium oxide (quicklime)

Calcining limestone drives off CO2, leaving behind calcium oxide (quicklime).

Question 13

Lime, in addition to its traditional use in mortars and plasters, has historically also been used in

  1. whitewashing (as a traditional surface coating/finish for walls)
  2. exclusively in the manufacture of glass, with no other traditional application
  3. exclusively as a food preservative, with no building application at all
  4. exclusively in steel manufacturing, with no building application
Show answer & solution

Answer: (A) whitewashing (as a traditional surface coating/finish for walls)

Whitewash, a traditional lime-based wall coating, is another classic use of lime beyond mortars and plaster.

Question 14

Poor or lean lime

  1. slakes rapidly with considerable evolution of heat
  2. takes very long time to develop adequate strength
  3. has high plasticity
  4. none of the above
Show answer & solution

Answer: (B) takes very long time to develop adequate strength

Poor limes have low cementing value and take a prolonged time to develop adequate structural strength.

Question 15

Quick lime is a

  1. carbonate of lime
  2. oxide of calcium
  3. product left immediately after the calcination of pure limestone
  4. lime quickly treated with water
Show answer & solution

Answer: (B) oxide of calcium

Quick lime (calcium oxide, CaO) is produced directly through the thermal calcination of limestone (calcium carbonate).

Question 16

Quick lime on reaction with water gives

  1. hydraulic lime
  2. slaked lime
  3. hydrated lime
  4. poor lime
Show answer & solution

Answer: (B) slaked lime

Adding water to quick lime (calcium oxide) initiates an exothermic hydration reaction, producing slaked lime (calcium hydroxide).

Question 17

Quicklime (calcium oxide), when mixed with water, undergoes a reaction known as

  1. carbonation, forming calcium carbonate directly
  2. slaking (or hydration), producing calcium hydroxide (slaked/hydrated lime), typically with significant heat release
  3. oxidation, forming rust
  4. polymerization, forming a plastic-like substance
Show answer & solution

Answer: (B) slaking (or hydration), producing calcium hydroxide (slaked/hydrated lime), typically with significant heat release

Adding water to quicklime causes slaking (an exothermic hydration reaction) producing slaked lime.

Question 18

The commonly used lime for works under water or in damp situations is

  1. fat lime
  2. lean lime
  3. feebly hydraulic lime
  4. eminently hydraulic lime
Show answer & solution

Answer: (D) eminently hydraulic lime

Eminently hydraulic lime sets and hardens in damp conditions or underwater because it does not rely solely on carbon dioxide from air to set.

Question 19

The constituent in lime which retards the slaking action and increases the rapidity of setting, is

  1. silica
  2. sulphate
  3. alkalies
  4. alumina
Show answer & solution

Answer: (A) silica

Silica combines chemically during burning to form calcium silicates, which slow slaking while accelerating hydraulic setting.

Question 20

The lime which consists almost entirely of calcium oxide, is called

  1. poor lime
  2. rich lime
  3. hydraulic lime
  4. limestone
Show answer & solution

Answer: (B) rich lime

Rich lime (also called fat lime) is composed predominantly of calcium oxide and slakes vigorously with high volume expansion.

Question 21

The lime which contains more than 30% of clayey impurities in the form of silica, alumina and iron oxide, is known as

  1. poor lime
  2. rich lime
  3. hydraulic lime
  4. limestone
Show answer & solution

Answer: (A) poor lime

Poor lime (lean lime) contains high clay impurities (>30%), slakes very slowly, and develops minimal binding strength.

Practice these 21 questions interactively →