Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Building Materials: Aggregates & Concrete

Civil Engineering · Building Materials

40 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

A higher fineness modulus value for a given aggregate generally indicates that the aggregate is, on average

  1. finer (smaller particle size), overall
  2. coarser (larger particle size), overall
  3. unrelated to particle size, being purely a chemical measure
  4. always unsuitable for use in concrete, regardless of the specific value
Show answer & solution

Answer: (B) coarser (larger particle size), overall

A higher fineness modulus corresponds to a coarser overall aggregate gradation.

Question 2

Accelerating admixtures, in contrast to retarders, are used mainly to

  1. speed up the setting time and/or early strength development of concrete, which can be useful in cold weather conditions or where rapid strength gain/formwork removal is desired
  2. slow down the setting time of concrete significantly, exactly opposite to their actual intended function
  3. have absolutely no effect on the concrete's setting or strength development
  4. act exclusively as a coloring agent, with no effect on setting time or strength at all
Show answer & solution

Answer: (A) speed up the setting time and/or early strength development of concrete, which can be useful in cold weather conditions or where rapid strength gain/formwork removal is desired

Accelerators speed setting/early strength gain, useful in cold weather or when fast formwork removal is needed.

Question 3

Aggregates are broadly classified, based on their source/origin, into

  1. natural aggregates (such as river sand and gravel) and artificial (manufactured) aggregates (such as crushed stone or, in some cases, blast furnace slag)
  2. only natural aggregates, with no artificial aggregates ever used in practice
  3. only artificial aggregates, with natural sources never used
  4. fine and coarse aggregate only, with no reference to source/origin
Show answer & solution

Answer: (A) natural aggregates (such as river sand and gravel) and artificial (manufactured) aggregates (such as crushed stone or, in some cases, blast furnace slag)

Aggregate origin classification splits naturally occurring sources from manufactured/processed ones.

Question 4

Aggregates containing deleterious materials such as clay, silt, or organic impurities are generally considered

  1. fully acceptable for high-quality concrete, with no limit on the amount present
  2. undesirable, since these impurities can interfere with the bond between cement paste and aggregate, or otherwise adversely affect concrete strength/durability, and their content is typically limited by specification
  3. beneficial, since they improve the workability of concrete
  4. irrelevant to concrete quality, having no known effect
Show answer & solution

Answer: (B) undesirable, since these impurities can interfere with the bond between cement paste and aggregate, or otherwise adversely affect concrete strength/durability, and their content is typically limited by specification

Clay, silt, and organics weaken the cement-aggregate bond, so their content is specification-limited.

Question 5

Alkali-aggregate reaction (or alkali-silica reaction, ASR) is a potentially damaging chemical reaction that can occur between

  1. certain reactive forms of silica present in some aggregates and the alkalis present in cement (and pore solution), producing an expansive gel that can cause cracking in concrete
  2. cement and water alone, with no involvement of aggregate at all
  3. coarse and fine aggregate particles reacting directly with each other, with no chemical involvement of cement
  4. steel reinforcement and concrete, with no reference to aggregate at all
Show answer & solution

Answer: (A) certain reactive forms of silica present in some aggregates and the alkalis present in cement (and pore solution), producing an expansive gel that can cause cracking in concrete

ASR occurs between reactive silica in certain aggregates and cement alkalis, forming an expansive gel that cracks concrete.

Question 6

Bulking of sand refers to the phenomenon in which

  1. moist sand occupies a larger volume than the same mass of completely dry sand, because surface tension of the moisture films pushes the sand grains apart
  2. sand always shrinks in volume when any moisture is present
  3. sand's volume is entirely unaffected by moisture content
  4. sand becomes heavier without any change in volume, when moisture is added
Show answer & solution

Answer: (A) moist sand occupies a larger volume than the same mass of completely dry sand, because surface tension of the moisture films pushes the sand grains apart

Surface tension in a moist sand film pushes grains apart, increasing bulk volume compared to the same mass fully dry or fully saturated.

Question 7

Coarse aggregate is generally defined as aggregate that

  1. mostly passes through a 4.75 mm sieve
  2. is predominantly retained on a 4.75 mm sieve, such as gravel or crushed stone
  3. is always finer than fine aggregate
  4. is used only in the manufacture of bricks, never concrete
Show answer & solution

Answer: (B) is predominantly retained on a 4.75 mm sieve, such as gravel or crushed stone

Coarse aggregate, like gravel or crushed stone, is defined by being predominantly retained on the 4.75 mm sieve.

Question 8

Fine aggregate is generally defined as aggregate that

  1. is entirely retained on a 4.75 mm sieve, with none passing through
  2. mostly passes through a 4.75 mm sieve, such as natural sand
  3. is always larger than 40 mm in size
  4. can only be a manufactured (crushed) material, never a natural material
Show answer & solution

Answer: (B) mostly passes through a 4.75 mm sieve, such as natural sand

Fine aggregate, like sand, is defined by mostly passing the 4.75 mm sieve.

Question 9

Fineness modulus of an aggregate is

  1. a single number obtained by summing the cumulative percentages retained on a specified series of sieves and dividing by 100, giving an index of the aggregate's overall fineness or coarseness
  2. the same as the specific gravity of the aggregate
  3. the same as the water absorption percentage of the aggregate
  4. a measure used exclusively for cement, never for aggregate
Show answer & solution

Answer: (A) a single number obtained by summing the cumulative percentages retained on a specified series of sieves and dividing by 100, giving an index of the aggregate's overall fineness or coarseness

Fineness modulus is a single index computed from cumulative sieve retention percentages, summarizing overall particle size.

Question 10

Flakiness index and elongation index of coarse aggregate are measures of the

  1. proportion of aggregate particles that are excessively flat or elongated in shape, which is generally undesirable for good quality concrete
  2. chemical composition of the aggregate
  3. specific gravity of the aggregate
  4. water absorption capacity of the aggregate
Show answer & solution

Answer: (A) proportion of aggregate particles that are excessively flat or elongated in shape, which is generally undesirable for good quality concrete

These indices quantify the fraction of poorly-shaped (flat or elongated) particles in an aggregate sample.

Question 11

Fly ash, a byproduct of burning pulverized coal in thermal power plants, is valued as a construction material mainly for its use as a

  1. primary structural reinforcement, functionally replacing steel reinforcing bars in reinforced concrete, in virtually all applications
  2. pozzolanic material, which can be blended with (or partially substituted for) Portland cement in concrete, reacting with the lime released during cement hydration to form additional cementitious compounds, and also used in manufacturing fly ash bricks
  3. primary coarse aggregate, functionally replacing natural stone/gravel, in virtually all concrete applications
  4. a material with no useful construction application whatsoever, requiring disposal as pure waste in every case
Show answer & solution

Answer: (B) pozzolanic material, which can be blended with (or partially substituted for) Portland cement in concrete, reacting with the lime released during cement hydration to form additional cementitious compounds, and also used in manufacturing fly ash bricks

Fly ash's main construction value is as a pozzolanic cement replacement/blend material, and for making fly ash bricks.

Question 12

Grading of aggregate refers to the

  1. color classification of the aggregate
  2. particle size distribution of the aggregate, i.e., the proportions of different particle sizes present, as determined by sieve analysis
  3. chemical composition of the aggregate only
  4. specific gravity of the aggregate only
Show answer & solution

Answer: (B) particle size distribution of the aggregate, i.e., the proportions of different particle sizes present, as determined by sieve analysis

Grading describes the distribution of particle sizes within an aggregate sample, found via sieve analysis.

Question 13

Retarding admixtures, another common category, are used mainly to

  1. accelerate the setting and early strength development of concrete, well beyond that of an unmodified mix
  2. delay (retard) the setting time of concrete, which can be useful in hot weather conditions, for large pours requiring an extended working time, or to prevent cold joints between successive concrete lifts
  3. have no effect whatsoever on the concrete's setting time or strength development
  4. act exclusively as a coloring agent, with no effect on setting time at all
Show answer & solution

Answer: (B) delay (retard) the setting time of concrete, which can be useful in hot weather conditions, for large pours requiring an extended working time, or to prevent cold joints between successive concrete lifts

Retarders slow setting, useful in hot weather, large pours, or to avoid cold joints between successive lifts.

Question 14

The abrasion value (such as from a Los Angeles abrasion test) of coarse aggregate is carried out to assess its resistance to

  1. sudden impact loading
  2. gradual crushing under a static compressive load
  3. wear due to rubbing, grinding, and impact from other aggregate particles and a set of steel balls, tumbling in a rotating drum
  4. chemical attack from acids in the environment
Show answer & solution

Answer: (C) wear due to rubbing, grinding, and impact from other aggregate particles and a set of steel balls, tumbling in a rotating drum

The Los Angeles abrasion test simulates wear from tumbling aggregate and steel balls in a rotating drum.

Question 15

The bulking of sand _____________ with addition of water upto about 5% by weight.

  1. increases
  2. decreases
Show answer & solution

Answer: (A) increases

Moisture films create surface tension around sand grains, pushing them apart and increasing bulk volume (bulking) up to ~5% moisture.

Question 16

The crushing value test on coarse aggregate is carried out to assess its

  1. resistance to gradual crushing (compressive) load, an indicator of its suitability for use in pavements/concrete subject to heavy loading
  2. color, compared to a reference standard
  3. water absorption over a 24-hour period
  4. fineness modulus
Show answer & solution

Answer: (A) resistance to gradual crushing (compressive) load, an indicator of its suitability for use in pavements/concrete subject to heavy loading

The crushing value test measures how well aggregate resists a gradually applied compressive crushing load.

Question 17

The impact value test on coarse aggregate is carried out to assess its

  1. resistance to a sudden impact (dynamic) load, as opposed to the gradual load applied in a crushing value test
  2. resistance to abrasion (wearing) from repeated rubbing/sliding contact
  3. chemical reactivity with cement
  4. bulking behavior with moisture
Show answer & solution

Answer: (A) resistance to a sudden impact (dynamic) load, as opposed to the gradual load applied in a crushing value test

The impact value test specifically measures resistance to sudden dynamic loading, unlike the gradual crushing test.

Question 18

The soundness test on aggregate, typically using repeated cycles of soaking in a saturated sodium or magnesium sulfate solution followed by drying, is carried out to assess the aggregate's resistance to

  1. disintegration/deterioration due to weathering effects (particularly freezing/thawing or wetting/drying cycles) it might experience in actual service
  2. crushing under a static compressive load
  3. impact from a sudden dynamic load
  4. abrasion from rubbing contact
Show answer & solution

Answer: (A) disintegration/deterioration due to weathering effects (particularly freezing/thawing or wetting/drying cycles) it might experience in actual service

The sulfate soundness test simulates weathering stresses (like freeze-thaw) to predict long-term durability.

Question 19

Water absorption of aggregate is an important property mainly because it affects the

  1. color of the finished concrete
  2. effective water content available for cement hydration in the concrete mix, and hence the water-cement ratio actually achieved
  3. magnetic properties of the aggregate
  4. setting time of the cement used, with no reference to the concrete's water content
Show answer & solution

Answer: (B) effective water content available for cement hydration in the concrete mix, and hence the water-cement ratio actually achieved

Absorptive aggregate can pull mix water away from cement hydration, effectively altering the real water-cement ratio.

Question 20

Admixtures, added to concrete (or mortar) in relatively small quantities during mixing, are used to modify specific properties, such as

  1. workability, setting time, or strength development, without significantly changing the basic proportions of cement, aggregate, and water in the mix
  2. the fundamental chemical nature of the cement itself, converting it into an entirely different binder material
  3. only the color of the finished concrete, with no effect on any other physical or mechanical property whatsoever
  4. the specific gravity of the coarse aggregate alone, with no effect on any other mix property
Show answer & solution

Answer: (A) workability, setting time, or strength development, without significantly changing the basic proportions of cement, aggregate, and water in the mix

Admixtures fine-tune workability, setting time, or strength without fundamentally changing the mix's basic proportions.

Question 21

Aggregates used in concrete are broadly classified, based on size, into

  1. fine aggregate and coarse aggregate
  2. heavy aggregate and light aggregate only
  3. natural and artificial aggregate only, with no reference to size
  4. round and angular aggregate only
Show answer & solution

Answer: (A) fine aggregate and coarse aggregate

The primary size-based classification of aggregate is fine versus coarse.

Question 22

Bulking of sand is an important consideration mainly when concrete or mortar is being proportioned by

  1. weight (mass), since bulking has no effect when materials are batched by weight
  2. volume, since the increased volume of moist sand (compared to dry sand of the same mass) can lead to under-proportioning of sand if this effect is not accounted for
  3. neither weight nor volume, since it has no practical significance at all
  4. color matching only, with no relevance to proportioning
Show answer & solution

Answer: (B) volume, since the increased volume of moist sand (compared to dry sand of the same mass) can lead to under-proportioning of sand if this effect is not accounted for

Since bulking changes volume (not mass), it specifically matters for volume-based batching, not weight-based batching.

Question 23

Consolidation of concrete should proceed

  1. before mixing
  2. before placing
  3. immediately after mixing
  4. immediately after placing
Show answer & solution

Answer: (D) immediately after placing

Concrete must be vibrated and consolidated immediately after being placed in formwork to expel entrapped air voids.

Question 24

Curing compounds, applied as a liquid membrane-forming coating to the surface of freshly placed concrete (as an alternative or supplement to water curing methods such as ponding or wet covering), are used mainly to

  1. rapidly and permanently seal moisture into the surrounding formwork itself, with absolutely no reference whatsoever to retaining any moisture within the concrete being cured
  2. reduce the rate of evaporation of moisture from the surface of the fresh concrete, thereby helping to retain sufficient moisture within the concrete for adequate, continued cement hydration and strength development
  3. have absolutely no relationship whatsoever to moisture retention, evaporation, hydration, or strength development in the concrete being cured, in any case whatsoever
  4. function exclusively and entirely as a permanent, final decorative surface color/finish coating for the concrete, with absolutely no reference whatsoever to any curing function at all
Show answer & solution

Answer: (B) reduce the rate of evaporation of moisture from the surface of the fresh concrete, thereby helping to retain sufficient moisture within the concrete for adequate, continued cement hydration and strength development

Curing compounds form a membrane that slows surface moisture evaporation, retaining water needed for continued hydration.

Question 25

Excessively flaky or elongated aggregate particles are generally undesirable in concrete mainly because they

  1. improve workability and strength significantly
  2. tend to reduce the workability of fresh concrete and can adversely affect the strength and durability of hardened concrete, compared to more cubical/rounded particles
  3. have no effect whatsoever on concrete properties
  4. are always more expensive to produce than well-shaped aggregate
Show answer & solution

Answer: (B) tend to reduce the workability of fresh concrete and can adversely affect the strength and durability of hardened concrete, compared to more cubical/rounded particles

Flat/elongated particles pack poorly and can create weak planes, reducing both workability and hardened concrete quality.

Question 26

Expansion joint filler materials, used to fill the gap deliberately provided at an expansion (movement) joint in a concrete structure/pavement, are generally chosen for their ability to

  1. remain relatively rigid and completely incompressible, providing absolutely no capacity whatsoever to compress or accommodate any subsequent movement of the adjoining concrete sections at the joint
  2. compress and expand to accommodate the anticipated movement of the adjoining concrete sections (due to thermal expansion/contraction, shrinkage, or other causes) at the joint, while helping to keep incompressible debris out of the joint gap itself
  3. dissolve completely and entirely in water within a very short time after initial installation, providing no lasting function whatsoever at the joint
  4. function exclusively and entirely as a structural, permanent, rigid bonding adhesive between the two adjoining concrete sections at the joint, with no reference whatsoever to accommodating any movement
Show answer & solution

Answer: (B) compress and expand to accommodate the anticipated movement of the adjoining concrete sections (due to thermal expansion/contraction, shrinkage, or other causes) at the joint, while helping to keep incompressible debris out of the joint gap itself

Joint fillers are chosen for compressibility, letting the joint accommodate movement while keeping debris out of the gap.

Question 27

Fly ash bricks and fly ash-blended cement (Portland Pozzolana Cement), both discussed earlier as construction materials, can also be considered examples of more sustainable material choices mainly because they

  1. productively utilize a byproduct/waste material (fly ash) from another industrial process (coal-fired power generation), which might otherwise require disposal as waste, thereby reducing the demand for some virgin raw materials and potentially reducing certain associated environmental impacts
  2. have absolutely no relationship whatsoever to any waste utilization, recycling, or environmental impact consideration at all
  3. always require significantly more energy to produce than conventional equivalent materials, in every single case, with no exception whatsoever
  4. can never actually meet any relevant recognized quality or performance standard, under any circumstances, and are therefore never actually usable in real, practical construction
Show answer & solution

Answer: (A) productively utilize a byproduct/waste material (fly ash) from another industrial process (coal-fired power generation), which might otherwise require disposal as waste, thereby reducing the demand for some virgin raw materials and potentially reducing certain associated environmental impacts

Fly ash products repurpose a power-plant waste byproduct, reducing both waste disposal and virgin raw material demand.

Question 28

Formwork release agents, applied to the internal surface of concrete formwork before placing fresh concrete, are used mainly to

  1. permanently and irreversibly bond the hardened concrete surface directly and completely to the formwork material itself, in every single case without any exception whatsoever
  2. facilitate the eventual, clean release/removal (stripping) of the formwork from the hardened concrete surface, while also generally helping to achieve a smoother, better-quality finished concrete surface
  3. have absolutely no relationship whatsoever to the ease of formwork removal or the resulting quality of the finished concrete surface, in any case whatsoever
  4. function exclusively and entirely as a structural reinforcement material, embedded permanently within the hardened concrete itself, with no reference whatsoever to the formwork or its removal
Show answer & solution

Answer: (B) facilitate the eventual, clean release/removal (stripping) of the formwork from the hardened concrete surface, while also generally helping to achieve a smoother, better-quality finished concrete surface

Release agents ease formwork stripping from hardened concrete and typically improve the resulting surface finish quality.

Question 29

Ground granulated blast furnace slag (GGBS), used as a cementitious material (often blended with Portland cement, or used to manufacture Portland Slag Cement), is a byproduct primarily of the

  1. manufacture of ceramic sanitary ware
  2. production of iron in a blast furnace, where the slag byproduct is suitably granulated and ground for use as a cementitious material
  3. manufacture of ordinary glass
  4. production of gypsum plasterboard, with no relation to iron production at all
Show answer & solution

Answer: (B) production of iron in a blast furnace, where the slag byproduct is suitably granulated and ground for use as a cementitious material

GGBS comes from granulating and grinding the slag byproduct of blast furnace iron production.

Question 30

Plasticizers (water-reducing admixtures), a common category of concrete admixture, are used mainly to

  1. increase the workability of fresh concrete for a given water content, or alternatively, allow a reduction in water content while maintaining a given workability (which can, in turn, improve strength/durability)
  2. significantly decrease the workability of fresh concrete, making it much stiffer and harder to place
  3. completely eliminate the need for any cement in the concrete mix
  4. act exclusively as a coloring agent, with no effect on workability or water content at all
Show answer & solution

Answer: (A) increase the workability of fresh concrete for a given water content, or alternatively, allow a reduction in water content while maintaining a given workability (which can, in turn, improve strength/durability)

Plasticizers boost workability at a given water content, or let water content drop for the same workability, improving strength/durability.

Question 31

Recycled aggregate, obtained mainly by crushing and processing demolished concrete (and/or masonry) waste, is increasingly being considered/used, at least for certain lower-demand construction applications, mainly to

  1. reduce the demand for virgin natural aggregate resources, and to help productively utilize construction/demolition waste, which would otherwise typically require landfill disposal
  2. always produce concrete of significantly and universally superior quality/strength compared to concrete made using conventional, good quality virgin natural aggregate, in every single application without any exception whatsoever
  3. completely and entirely eliminate any need for cement in the resulting concrete mix, in every case
  4. have absolutely no relationship whatsoever to any waste reduction, resource conservation, or recycling consideration at all
Show answer & solution

Answer: (A) reduce the demand for virgin natural aggregate resources, and to help productively utilize construction/demolition waste, which would otherwise typically require landfill disposal

Recycled aggregate reduces demand for virgin materials while productively reusing demolition waste that would otherwise go to landfill.

Question 32

Silica fume, another pozzolanic material sometimes used as a partial cement replacement/addition in high-performance concrete, is a very fine byproduct material generated mainly from the production of

  1. ordinary Portland cement clinker itself, with no relation to any other industrial process
  2. silicon or ferrosilicon alloys, in specific industrial (electric arc furnace) processes
  3. ordinary clay bricks, during their firing process
  4. plain natural sand, with no relation to any industrial byproduct at all
Show answer & solution

Answer: (B) silicon or ferrosilicon alloys, in specific industrial (electric arc furnace) processes

Silica fume is a very fine byproduct of silicon/ferrosilicon alloy production in electric arc furnaces.

Question 33

The density of concrete _____________ with increase in the size of aggregate.

  1. does not change
  2. increases
  3. decreases
Show answer & solution

Answer: (B) increases

Larger, well-graded aggregates pack more densely with fewer interstitial voids, increasing overall concrete density.

Question 34

The durability of cement concrete is usually improved by

  1. increasing the quantity of coarse sand
  2. increasing the quantity of cement
  3. decreasing the water-cement ratio
  4. decreasing the proportion of fine aggregate
Show answer & solution

Answer: (C) decreasing the water-cement ratio

Lowering the water-cement ratio reduces capillary porosity, enhancing strength, impermeability, and overall durability.

Question 35

The maximum water-cement ratio for durable concrete is

  1. 0.2
  2. 0.4
  3. 0.6
  4. 0.8
Show answer & solution

Answer: (C) 0.6

To maintain adequate impermeability and durability against weathering, standard general specifications limit water-cement ratios to a maximum of 0.6.

Question 36

The slump test of concrete is used to measure its

  1. consistency
  2. tensile and compressive strength
  3. impact value
  4. homogeneity
Show answer & solution

Answer: (A) consistency

The slump cone test is a standard site method used to evaluate the workability and consistency of fresh concrete mixes.

Question 37

The specific gravity of most common natural aggregates (such as granite or limestone) used in concrete generally falls in the approximate range of

  1. 0.5 to 0.8
  2. 2.5 to 2.8
  3. 5.0 to 6.0
  4. 10.0 to 12.0
Show answer & solution

Answer: (B) 2.5 to 2.8

Typical dense natural aggregates fall in the 2.5-2.8 specific gravity range.

Question 38

The strength of cement concrete is directly proportional to cement-water ratio.

  1. Agree
  2. Disagree
Show answer & solution

Answer: (A) Agree

Abrams' law states that concrete strength depends inversely on water-cement ratio; thus, strength is directly proportional to the cement-water ratio.

Question 39

Waterproofing admixtures (or integral waterproofing compounds), added to a concrete mix, are used mainly to

  1. reduce the permeability of the hardened concrete to water, helping to resist water penetration through the concrete mass
  2. significantly increase the concrete's permeability to water, allowing much easier water penetration through the concrete
  3. have absolutely no effect whatsoever on the concrete's permeability to water
  4. function exclusively as a coloring agent, with no effect on permeability at all
Show answer & solution

Answer: (A) reduce the permeability of the hardened concrete to water, helping to resist water penetration through the concrete mass

Waterproofing admixtures reduce hardened concrete's permeability, helping resist water penetration.

Question 40

Well-graded aggregate, containing a good, continuous distribution of particle sizes from coarse to fine, is generally preferred in concrete mainly because it

  1. leads to a more compact, well-packed mix with fewer voids, generally requiring less cement paste to fill the voids for a given workability
  2. always leads to weaker, more porous concrete
  3. has no bearing on the resulting concrete's properties
  4. requires significantly more water for the same workability, in every case
Show answer & solution

Answer: (A) leads to a more compact, well-packed mix with fewer voids, generally requiring less cement paste to fill the voids for a given workability

A continuous size distribution packs tightly, minimizing voids and the cement paste needed to fill them.

Practice these 40 questions interactively →