Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Building Materials: Cement (Properties & Tests)

Civil Engineering · Building Materials

20 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Le-chatelier method is used to determine

  1. initial setting of cement
  2. fineness of cement
  3. soundness of cement
  4. normal consistency of cement
Show answer & solution

Answer: (C) soundness of cement

The Le-Chatelier apparatus detects unsoundness in cement caused by excessive free lime expansion.

Question 2

Greater fineness of cement generally results in

  1. slower rate of hydration and lower early strength
  2. faster rate of hydration and higher early strength, though it may also increase the heat of hydration and shrinkage
  3. no effect on the rate of hydration or strength development
  4. reduced water demand for a given workability
Show answer & solution

Answer: (B) faster rate of hydration and higher early strength, though it may also increase the heat of hydration and shrinkage

Finer cement particles hydrate faster, boosting early strength, but at the cost of higher heat generation and shrinkage.

Question 3

The compound in cement mainly responsible for later (long-term) strength gain is

  1. Tricalcium aluminate (C3A)
  2. Dicalcium silicate (C2S)
  3. gypsum
  4. free lime
Show answer & solution

Answer: (B) Dicalcium silicate (C2S)

C2S hydrates more slowly, contributing mainly to the continued strength gain beyond 28 days.

Question 4

The compound responsible for the initial setting of cement is

  1. tri-calcium aluminate
  2. tetra-calcium alumino ferrite
  3. di-calcium silicate
  4. tri-calcium silicate
Show answer & solution

Answer: (A) tri-calcium aluminate

Tri-calcium aluminate (C3A) hydrates very rapidly upon water addition, controlling the initial setting behavior of cement.

Question 5

The compressive strength of cement is standard-tested using cement mortar cubes, typically checked at ages of

  1. only 1 hour, with no later testing
  2. 3 days, 7 days, and 28 days, as common standard testing ages
  3. only 100 days, with no earlier testing
  4. only 1 year, with no earlier testing
Show answer & solution

Answer: (B) 3 days, 7 days, and 28 days, as common standard testing ages

Standard cement testing checks compressive strength at 3, 7, and 28 days on mortar cubes.

Question 6

The expansion of cement should not exceed _____________ for any type of Portland cement.

  1. 5 mm
  2. 10 mm
  3. 15 mm
  4. 20 mm
Show answer & solution

Answer: (B) 10 mm

Using the Le-Chatelier test, expansion caused by free lime in Portland cement must not exceed 10 mm.

Question 7

The final setting time of ordinary Portland cement, as tested by the Vicat apparatus, should generally not exceed

  1. 30 minutes
  2. 10 hours (600 minutes)
  3. 100 hours
  4. 5 minutes
Show answer & solution

Answer: (B) 10 hours (600 minutes)

Standard specifications cap the final setting time at around 10 hours (600 minutes).

Question 8

The final setting time of ordinary cement should not be more than

  1. 2 hours
  2. 4 hours
  3. 8 hours
  4. 10 hours
Show answer & solution

Answer: (D) 10 hours

Standard specifications require ordinary Portland cement to achieve final set within 10 hours so hardening proceeds reliably.

Question 9

The fineness of cement is commonly tested using

  1. a sieve analysis (such as the 90-micron sieve test) or a Blaine air permeability test
  2. a slump cone test
  3. a compression testing machine
  4. a Vicat apparatus exclusively, with no other method
Show answer & solution

Answer: (A) a sieve analysis (such as the 90-micron sieve test) or a Blaine air permeability test

Fineness is standardly measured by sieve residue or the Blaine air permeability method.

Question 10

The grade of ordinary Portland cement, such as 33, 43, or 53, indicates its

  1. color
  2. minimum compressive strength (in N/mm2, or MPa) at 28 days, as tested on standard mortar cubes
  3. fineness only
  4. setting time only
Show answer & solution

Answer: (B) minimum compressive strength (in N/mm2, or MPa) at 28 days, as tested on standard mortar cubes

The grade number directly states the minimum 28-day compressive strength guaranteed for that cement.

Question 11

The initial setting time of ordinary Portland cement, as tested by the Vicat apparatus, should generally not be less than

  1. 30 minutes
  2. 10 hours
  3. 24 hours
  4. 5 minutes
Show answer & solution

Answer: (A) 30 minutes

Standard specifications require an initial setting time of at least 30 minutes.

Question 12

The initial setting time of rapid hardening cement should not be less than

  1. 30 min
  2. 1 hour
  3. 4 hours
  4. 8 hours
Show answer & solution

Answer: (A) 30 min

Like ordinary cement, rapid hardening cement must allow adequate working time, with initial setting time not less than 30 minutes.

Question 13

The main chemical compound in cement responsible for early strength gain is

  1. Tricalcium silicate (C3S)
  2. Dicalcium silicate (C2S)
  3. Tetracalcium aluminoferrite (C4AF)
  4. free lime
Show answer & solution

Answer: (A) Tricalcium silicate (C3S)

C3S hydrates relatively quickly, giving cement most of its early (up to about 28-day) strength.

Question 14

The normal consistency of Portland cement is about

  1. 10%
  2. 15%
  3. 20%
  4. 25%
Show answer & solution

Answer: (D) 25%

Standard Vicat needle tests show normal consistency paste requirements clustering around 25% to 30% water by weight.

Question 15

The normal consistency of a cement paste, determined using the Vicat apparatus, refers to the

  1. water content at which the paste reaches its maximum possible strength
  2. water content that gives the paste a standard, specified penetration/consistency, used as a basis for further setting time and soundness tests
  3. the exact amount of gypsum added during manufacture
  4. the fineness of the cement, expressed as a percentage
Show answer & solution

Answer: (B) water content that gives the paste a standard, specified penetration/consistency, used as a basis for further setting time and soundness tests

Normal consistency defines the water content giving a standard paste stiffness, used as the basis for subsequent setting-time and soundness tests.

Question 16

The soundness of cement, tested using the Le Chatelier apparatus (or autoclave test), is a measure of its

  1. tendency to undergo excessive, disruptive volume expansion after setting, mainly due to free (uncombined) lime, magnesia, or excess calcium sulfate
  2. compressive strength at 28 days
  3. fineness, expressed as a percentage passing a sieve
  4. color, compared to a standard reference
Show answer & solution

Answer: (A) tendency to undergo excessive, disruptive volume expansion after setting, mainly due to free (uncombined) lime, magnesia, or excess calcium sulfate

Soundness testing checks for expansive tendencies from unreacted free lime/magnesia that could crack hardened cement later.

Question 17

The specific gravity of ordinary Portland cement is approximately

  1. 1.0
  2. 3.15
  3. 5.5
  4. 7.8
Show answer & solution

Answer: (B) 3.15

OPC has a typical specific gravity of about 3.15.

Question 18

The specific surface (in cm²/g) of a good Portland cement should not be less than

  1. 500
  2. 1100
  3. 2250
  4. 3200
Show answer & solution

Answer: (C) 2250

A good quality Portland cement must have a minimum specific surface area of 2250 cm²/g (225 m²/kg) as measured by Blaine permeability.

Question 19

The ultimate strength of cement is provided by

  1. silica
  2. di-calcium silicate
  3. tri-calcium silicate
  4. tri-calcium aluminate
Show answer & solution

Answer: (B) di-calcium silicate

Di-calcium silicate (C2S) hydrates slowly over months, contributing significantly to long-term ultimate strength and durability.

Question 20

Tricalcium aluminate (C3A) in cement is associated mainly with

  1. high early strength and low heat of hydration
  2. rapid setting/hydration and relatively high heat of hydration, but contributing little to long-term strength
  3. resistance to sulfate attack
  4. color of the cement
Show answer & solution

Answer: (B) rapid setting/hydration and relatively high heat of hydration, but contributing little to long-term strength

C3A reacts and hydrates very quickly, generating significant heat, but adds little to the cement's ultimate strength.

Practice these 20 questions interactively →