Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.
Question 1
Traffic engineering is mainly concerned with:
- acquisition and valuation of land for new highway corridors and interchanges
- structural design of bridge girders, piers and foundations for highway crossings
- laboratory testing and quality control of road construction materials
- planning, design and operation of roads and traffic control for safe movement
Show answer & solution
Answer: (D) planning, design and operation of roads and traffic control for safe movement
Traffic engineering deals with the safe and efficient movement of people and goods.
Question 2
A traffic volume study is used mainly to:
- calculate the stopping sight distance for a chosen design speed
- count the vehicles, by type, passing a point in a given time
- find where the trips on a network begin and end for each zone
- measure the structural strength of the pavement layers on a road
Show answer & solution
Answer: (B) count the vehicles, by type, passing a point in a given time
Volume counts show how much traffic uses a road.
Question 3
Average Daily Traffic (ADT) is the:
- average number of vehicles passing a point per day over a stated period
- number of vehicles observed at one point at a single moment in time
- number of vehicles passing a point during the busiest hour of a normal working day
- maximum number of vehicles that one lane can carry in a day
Show answer & solution
Answer: (A) average number of vehicles passing a point per day over a stated period
ADT is the total count divided by the number of days of observation.
Question 4
Annual Average Daily Traffic (AADT) is the average daily traffic over:
- a single typical weekday
- the busiest month of the year only
- a full year (365 days)
- the peak hour of each day
Show answer & solution
Answer: (C) a full year (365 days)
AADT is the yearly total divided by 365.
Question 5
Peak Hour Volume (PHV) is the:
- traffic volume in the busiest hour of the day
- number of vehicles passing in the busiest five minutes
- volume recorded in the quietest hour of the night
- average hourly volume taken over the full 24 hours
Show answer & solution
Answer: (A) traffic volume in the busiest hour of the day
Peak-hour volume is important for geometric and signal design.
Question 6
The Peak Hour Factor (PHF) is the ratio of:
- total daily volume to the total yearly volume of traffic on the road
- average hourly volume to the total daily volume of traffic on the road
- peak hour volume to four times the peak 15-minute volume in that hour
- peak 15-minute volume to the design capacity of the lane in use
Show answer & solution
Answer: (C) peak hour volume to four times the peak 15-minute volume in that hour
Question 7
Speed studies are used mainly to:
- measure the roughness of the pavement surface along a section
- find the actual speeds of vehicles on a road section
- find the origins and destinations of the trips made by users
- count the number of axles passing a given point on the road
Show answer & solution
Answer: (B) find the actual speeds of vehicles on a road section
Spot speed studies support speed limits and safety analysis.
Question 8
The 85th percentile speed is the speed:
- of the fastest vehicle among all of the vehicles that were observed
- exceeded by 85% of all of the vehicles that were observed
- equal to the arithmetic mean of all of the observed vehicle speeds
- below which 85% of the observed vehicles travel
Show answer & solution
Answer: (D) below which 85% of the observed vehicles travel
It is often used as a reference for setting speed limits.
Question 9
The space mean speed of a traffic stream is the:
- median of the spot speeds
- harmonic mean of the spot speeds
- 85th percentile of the spot speeds
- arithmetic mean of the spot speeds
Show answer & solution
Answer: (B) harmonic mean of the spot speeds
Time mean speed is the arithmetic mean; space mean speed is the harmonic mean.
Question 10
An origin–destination (O–D) study is used mainly to find:
- how strong the subgrade is along the length of the route
- how fast the vehicles travel on each road section of the network
- how much camber is provided on each of the carriageways
- where the trips on a network begin and end
Show answer & solution
Answer: (D) where the trips on a network begin and end
O–D data support network planning.
Question 11
The Passenger Car Unit (PCU):
- expresses each vehicle type's effect on flow as a number of equivalent cars
- gives every type of vehicle the same value of 1.0 whatever its size and performance
- converts the speed of a vehicle into its volume on the road
- is used only for counting the pedestrians who cross at a junction
Show answer & solution
Answer: (A) expresses each vehicle type's effect on flow as a number of equivalent cars
PCU values let mixed traffic be converted into a single standard unit.
Question 12
Traffic flow (veh/h) equals:
- density (veh/km) divided by space mean speed (km/h) on the section
- space mean speed (km/h) divided by time headway (s) on the section
- density (veh/km) multiplied by space mean speed (km/h)
- time headway (s) multiplied by space mean speed (km/h) on the section
Show answer & solution
Answer: (C) density (veh/km) multiplied by space mean speed (km/h)
The fundamental relation is q = k × u.
Question 13
- distance between the successive vehicles that are travelling on the road
- time taken by a traffic signal to complete one full cycle
- time taken by a vehicle to cross the whole of an intersection
- time between successive front bumpers passing a point
Show answer & solution
Answer: (D) time between successive front bumpers passing a point
Flow equals the reciprocal of the average headway.
Question 14
- maximum number of vehicles that can reasonably pass a point in a given time
- average number of vehicles observed in the peak hour on a normal weekday
- design speed multiplied by the width of one traffic lane
- total number of vehicles using the road during the whole of one year
Show answer & solution
Answer: (A) maximum number of vehicles that can reasonably pass a point in a given time
Capacity is a property of the road and its conditions.
Question 15
Traffic calming measures are used mainly to:
- raise vehicle speeds on residential streets and other local roads in towns
- collect fees from vehicles entering the built-up areas of a city
- reduce vehicle speeds and discourage through traffic in sensitive areas
- widen the carriageway to increase capacity in town centres and markets
Show answer & solution
Answer: (C) reduce vehicle speeds and discourage through traffic in sensitive areas
Humps, chicanes and narrowings improve safety for pedestrians in residential areas.
Question 16
Traffic control devices mainly:
- collect and drain the surface water away from the pavement
- regulate, warn and guide road users
- measure the volume and the speed of the passing traffic
- carry the vehicle loads down to the subgrade soil beneath
Show answer & solution
Answer: (B) regulate, warn and guide road users
Signs, signals and markings are the main traffic control devices.
Question 17
Traffic signs are generally classified into:
- mandatory, optional and decorative signs
- stationary, rolling and floating signs
- primary, secondary and tertiary route signs
- regulatory, warning and informatory (guide) signs
Show answer & solution
Answer: (D) regulatory, warning and informatory (guide) signs
Regulatory signs command, warning signs caution, and informatory signs guide.
Question 18
The shape of a STOP sign is:
- octagonal
- triangular
- square
- circular
Show answer & solution
Answer: (A) octagonal
The octagon is reserved internationally for the STOP sign.
Question 19
A STOP sign requires a driver to:
- slow down and drive on without stopping if the road looks clear of traffic
- stop completely and proceed only when safe, yielding to other traffic
- give way to pedestrians but not to other vehicles at the junction
- stop only when other vehicles are visible at the junction ahead
Show answer & solution
Answer: (B) stop completely and proceed only when safe, yielding to other traffic
A full stop is compulsory regardless of other traffic.
Question 20
A 'GIVE WAY' sign requires a driver to:
- stop for pedestrians but not for any other vehicles
- sound the horn and continue through the junction at the same speed
- slow down and yield to priority traffic, stopping only if necessary
- come to a complete stop at the line every time without any exception
Show answer & solution
Answer: (C) slow down and yield to priority traffic, stopping only if necessary
Give way differs from STOP because a stop is not required if the way is clear.
Question 21
Road markings serve mainly to:
- supplement signs by regulating, guiding and warning drivers
- carry part of the structural load of traffic into the pavement layers
- increase the camber of the carriageway on the curved sections
- drain rain water from the surface towards the kerb or shoulder
Show answer & solution
Answer: (A) supplement signs by regulating, guiding and warning drivers
Markings convey information directly on the road surface.
Question 22
A centre line marking on a two-way road mainly:
- indicates the position of a pedestrian crossing on the road
- marks the outer edge of the carriageway for each direction of travel
- separates opposing traffic and shows if overtaking is allowed
- shows the limits of the permitted parking zone beside the road
Show answer & solution
Answer: (C) separates opposing traffic and shows if overtaking is allowed
Broken lines may be crossed to overtake when safe; continuous lines may not.
Question 23
Retroreflective sheeting on traffic signs is used because it:
- makes the sign lighter and easier to mount on the supporting posts
- absorbs the headlight beam so that the driver is not troubled by glare
- lowers the cost of the sign when compared with painted metal
- reflects headlight beams back to the driver, improving night visibility
Show answer & solution
Answer: (D) reflects headlight beams back to the driver, improving night visibility
Retroreflection returns light along the path it came from.
Question 24
A Variable Message Sign (VMS) is used mainly to:
- mark the edges of the traffic lanes on the carriageway at night
- display real-time or changing information to road users
- measure the speed of the vehicles that pass the sign on the road
- separate the opposing traffic streams on a divided highway
Show answer & solution
Answer: (B) display real-time or changing information to road users
VMS can warn of incidents, congestion and diversions.
Question 25
- give permanent priority to the main road over the minor road at all times
- assign the right-of-way alternately to conflicting traffic movements
- remove every stop for the vehicles approaching the junction
- slow all of the vehicles down to a single common speed
Show answer & solution
Answer: (B) assign the right-of-way alternately to conflicting traffic movements
Signals separate conflicting movements in time.
Question 26
Signal timing and phasing mainly affect the:
- grade of bitumen specified for the approach roads at the junction
- thickness of the pavement layers used at the junction approaches
- strength of the subgrade soil under the junction area
- delay, capacity and safety of the intersection
Show answer & solution
Answer: (D) delay, capacity and safety of the intersection
Good timing reduces delay and conflicts.
Question 27
Signal coordination ('green wave') aims to:
- time successive signals so vehicles at a suitable speed avoid stopping
- maximize the number of stops for vehicles travelling along a corridor
- show red at all of the signals along the corridor at the same moment
- remove all of the pedestrian phases from the signal cycle in use
Show answer & solution
Answer: (A) time successive signals so vehicles at a suitable speed avoid stopping
Progressive timing reduces stops and delay along a corridor.
Question 28
Webster's formula for the optimum cycle length of a signal is:
- C = (1.5L − 5)/(1 − Y)
- C = L/(1.5 + Y)
- C = (1.5L + 5)/(1 − Y)
- C = (1.5L + 5)(1 − Y)
Show answer & solution
Answer: (C) C = (1.5L + 5)/(1 − Y)
L is the total lost time per cycle and Y the sum of the critical flow ratios.
Question 29
The amber interval at a traffic signal mainly:
- lets turning vehicles move freely through the junction at any time
- clears vehicles already in the junction before conflicting flows start
- gives priority to traffic on the minor road for a short period
- extends the red phase for the opposing approach to the junction
Show answer & solution
Answer: (B) clears vehicles already in the junction before conflicting flows start
Amber warns drivers that the right-of-way is about to change.