The right-of-way (land width) of a highway is important because it:
Show answer & solution
Answer: (A) holds the cross-section and reserves room for widening
Right-of-way provides room for the carriageway, shoulders, drains and later widening.
Civil Engineering · Highway Engineering
29 questions, each with the answer and a worked solution.
Practice interactively and track your score →The right-of-way (land width) of a highway is important because it:
Answer: (A) holds the cross-section and reserves room for widening
Right-of-way provides room for the carriageway, shoulders, drains and later widening.
The cross-section of a highway generally consists of:
Answer: (D) carriageway, shoulders, camber and a median
A typical cross-section includes the carriageway, shoulders, camber and median where provided.
The paved portion of a road used by vehicular traffic is known as the:
Answer: (B) carriage-way
The carriageway (travelled way) is the portion of the road meant for moving vehicles.
A median on a divided highway mainly serves to:
Answer: (C) separate opposing traffic and prevent head-on crashes
Medians keep opposing streams apart and can hold space for future widening or barriers.
Shoulders along the carriageway mainly serve to:
Answer: (D) support the pavement edge and allow emergency stops
Shoulders support the pavement edge and give vehicles a place to stop clear of the traffic lanes.
Kerbs along the edge of a carriageway mainly:
Answer: (C) mark the pavement edge and help guide drainage
Kerbs mark the carriageway edge, guide surface water and discourage vehicles from leaving the pavement.
The standard minimum lane width recommended for multi-lane national highways in Pakistan is:
Answer: (B) 3.65 m
National highway lanes are generally 3.65 m wide.
The maximum width of a commercial road vehicle permitted under standard highway codes is about:
Answer: (A) 2.44 m to 2.50 m
Legal vehicle width limits are around 2.5 m, which lane widths are designed to accommodate.
The highest point of the cross-section of a cambered road is called the:
Answer: (C) crown
The crown is the highest point on a cambered cross-section, from which the surface slopes away.
An excessively steep camber on a road causes:
Answer: (B) traffic to bunch near the crown and wear it out
A steep camber makes drivers keep to the crown, where the surface wears out first.
Sight distance is:
Answer: (A) the length of road visible ahead
Sight distance is the length of road ahead that a driver can see.
Stopping sight distance is the minimum distance a driver needs to:
Answer: (D) stop the vehicle after seeing an obstacle
Stopping sight distance lets the driver perceive a hazard and stop before reaching it.
Stopping sight distance is the sum of:
Answer: (C) the lag distance and the braking distance
SSD = distance travelled during reaction time + distance travelled while braking.
Find the stopping sight distance for a design speed of 60 km/h, reaction time of 2.5 s and coefficient of friction 0.35 on a level road. (SSD = 0.278Vt + V²/254f)
Answer: (B) about 82 m
SSD = 0.278×60×2.5 + 60²/(254×0.35) = 41.7 + 40.5 ≈ 82 m.
The perception–reaction time commonly adopted in stopping sight distance design is:
Answer: (A) 2.5 seconds
A reaction time of 2.5 s is the usual design value for SSD.
Overtaking sight distance is the minimum distance a driver needs to:
Answer: (D) overtake a slower vehicle and return to its own lane
OSD covers the whole overtaking manoeuvre, including the opposing lane's clear view.
For a given design speed, overtaking sight distance compared with stopping sight distance is:
Answer: (C) considerably longer
A complete overtaking manoeuvre needs much more road than a simple stop.
Intermediate sight distance (ISD) is generally taken as about:
Answer: (A) twice the stopping sight distance
ISD ≈ 2 × SSD, a compromise where full OSD cannot be provided.
Adequate sight distance on a horizontal curve is ensured mainly by:
Answer: (B) clearing obstructions on the inside of the curve
Buildings, walls and vegetation on the inside of the curve block the line of sight and must be cleared.
The length of a summit (crest) vertical curve is designed mainly to provide:
Answer: (D) adequate stopping sight distance over the crest
On a crest the view is cut off by the road surface, so curve length is set by sight distance.
The length of a sag (valley) vertical curve is governed mainly by headlight sight distance and:
Answer: (A) passenger comfort
On sags the night-time headlight beam and comfort limit the curve length.
Vertical curves in highway design are generally designed as:
Answer: (D) parabolas
A parabola gives a constant rate of change of grade, which suits vertical curves.
The vertical alignment of a road refers to its:
Answer: (C) longitudinal profile (elevation and grade)
Vertical alignment is the profile of the road along its length.
The rate of rise or fall of the road surface along its length is called the:
Answer: (B) gradient
Gradient is the longitudinal rise or fall per unit horizontal distance.
If the difference in level between two points on a road is 1.5 m and their horizontal distance is 75 m, the gradient is:
Answer: (C) 1 in 50 or 2%
Gradient = 1.5/75 = 1/50 = 2%.
Expressways are generally designed for:
Answer: (A) high speeds, generous geometry, controlled access
Expressways give high-speed, high-capacity travel through controlled access and high geometric standards.
Geometric design standards for a road class are chosen mainly to:
Answer: (D) suit the function and speed of the road
Standards match geometry to the role and speed of each class of road.
Design speed is the speed:
Answer: (B) adopted as the basis for curve radius and sight distance
Design speed is a selected reference speed for geometric design.
Once chosen, the design speed of a highway governs:
Answer: (C) minimum curve radius, sight distance and super-elevation
Most geometric elements are derived from the design speed.