Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Highway Engineering: Pavement Design, Distress & Maintenance

Civil Engineering · Highway Engineering

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

A flexible pavement transfers wheel loads to the subgrade mainly through:

  1. the tensile strength of steel reinforcement bars embedded in layers
  2. dowel bars carrying shear across the transverse joints in slabs
  3. the flexural strength of a stiff concrete layer placed above
  4. grain contact spreading the load over a widening area
Show answer & solution

Answer: (D) grain contact spreading the load over a widening area

In flexible pavements the stress spreads out through the layers and decreases with depth.

Question 2

The Equivalent Standard Axle Load (ESAL) concept is used to:

  1. estimate the average speed of a mixed traffic stream at peak hour
  2. convert mixed traffic into standard axle repetitions
  3. count the vehicles passing through an intersection every hour
  4. measure the surface roughness of the wearing course in m/km
Show answer & solution

Answer: (B) convert mixed traffic into standard axle repetitions

ESAL expresses the damaging effect of different axle loads in terms of one standard axle.

Question 3

The damage caused to a pavement by an axle load is roughly proportional to the:

  1. fourth power of the axle load
  2. cube of the axle load
  3. square of the axle load
  4. axle load itself, in direct proportion
Show answer & solution

Answer: (A) fourth power of the axle load

According to the fourth-power law, a doubled axle load does about 16 times the damage.

Question 4

Overloading of commercial vehicles is a serious concern mainly because it:

  1. slightly improves load distribution in the layers
  2. mainly increases the skid resistance of the surface
  3. greatly accelerates pavement deterioration
  4. has no effect on the pavement fatigue life
Show answer & solution

Answer: (C) greatly accelerates pavement deterioration

Pavement damage rises very sharply with axle load.

Question 5

Weigh-in-motion (WIM) systems are used mainly to:

  1. count vehicles for the traffic volume study each hour
  2. measure spot speeds of vehicles passing a road section
  3. record the origins and destinations of trips on a network
  4. weigh vehicles at traffic speed without stopping them
Show answer & solution

Answer: (D) weigh vehicles at traffic speed without stopping them

WIM sensors weigh vehicles at traffic speed for planning and enforcement.

Question 6

Axle load surveys and enforcement are used mainly to:

  1. forecast the design rainfall for culvert design work
  2. monitor and control overloading and its damage
  3. measure the camber of the carriageway surface in the field
  4. design the transition curves provided on sharp horizontal bends
Show answer & solution

Answer: (B) monitor and control overloading and its damage

Controlling overloading preserves pavement life.

Question 7

Traffic composition is important in highway design because:

  1. vehicle types differ in size, performance and axle loads
  2. it directly fixes the camber of the carriageway surface
  3. it alone determines the right-of-way width that is needed
  4. all vehicle types have an identical effect on the road
Show answer & solution

Answer: (A) vehicle types differ in size, performance and axle loads

Heavy vehicles dominate pavement damage while all types affect capacity.

Question 8

Rutting in a flexible pavement is mainly caused by:

  1. thermal contraction cracking of the bituminous surface layer
  2. frost heave of the subgrade soil beneath the pavement
  3. permanent deformation building up under repeated loads
  4. poor camber that lets water pond on the road surface
Show answer & solution

Answer: (C) permanent deformation building up under repeated loads

Rutting is longitudinal depressions in the wheel paths.

Question 9

Fatigue (alligator) cracking in a flexible pavement is mainly caused by:

  1. repeated loading causing cumulative damage in the layer
  2. a single sudden overload applied once to the pavement layer
  3. excess camber that sheds the rain water too quickly
  4. poor colour and texture of the wearing surface material
Show answer & solution

Answer: (A) repeated loading causing cumulative damage in the layer

Repeated bending under wheels eventually cracks the bound layer.

Question 10

Potholes generally develop from:

  1. an excess of tack coat sprayed between the layers
  2. excess skid resistance that wears down the tyres quickly
  3. too much camber that drains the water from the surface
  4. disintegration that often starts with water-entry cracks
Show answer & solution

Answer: (D) disintegration that often starts with water-entry cracks

Water entering through cracks weakens the layers and traffic dislodges material.

Question 11

Bleeding in a bituminous surface is the:

  1. longitudinal cracking along the wheel paths
  2. upward movement of excess binder to the surface
  3. loss of aggregate particles from the wearing surface
  4. settlement of the subgrade under the road
Show answer & solution

Answer: (B) upward movement of excess binder to the surface

Bleeding reduces skid resistance in hot weather.

Question 12

Ravelling of a bituminous surface refers to the:

  1. expansion of concrete slabs in hot weather conditions
  2. formation of wheel-path ruts in the pavement layers
  3. progressive loss of aggregate particles from the surface
  4. upward flow of excess binder onto the pavement surface
Show answer & solution

Answer: (C) progressive loss of aggregate particles from the surface

Weak adhesion or ageing of the binder lets stones dislodge.

Question 13

Overlay design generally aims to:

  1. restore the strength and ride quality of the old pavement
  2. lower the camber of the existing carriageway surface
  3. raise the design speed of the highway section
  4. change the horizontal alignment of the existing road
Show answer & solution

Answer: (A) restore the strength and ride quality of the old pavement

An overlay is a new layer placed over the old pavement to extend its life.

Question 14

The Benkelman beam is used mainly to:

  1. test the quality of the aggregate at its source
  2. measure rebound deflection under a wheel load
  3. measure the pavement temperature at various depths
  4. count the axles passing a survey point in an hour
Show answer & solution

Answer: (B) measure rebound deflection under a wheel load

Deflection measurements help design overlays.

Question 15

Empirical pavement design methods rely mainly on:

  1. the source of the aggregate used in the bituminous mix
  2. purely theoretical stress analysis of the pavement layers
  3. relationships from field observations and experience
  4. the colour of the wearing surface material alone
Show answer & solution

Answer: (C) relationships from field observations and experience

Empirical methods correlate performance with design inputs.

Question 16

Mechanistic–empirical pavement design combines:

  1. laboratory tests of the bitumen properties only
  2. field experience only, with no theoretical analysis at all
  3. traffic counts taken at the road section alone
  4. stress analysis with calibrated performance models
Show answer & solution

Answer: (D) stress analysis with calibrated performance models

ME design uses structural response models calibrated against observed performance.

Question 17

A pavement management system (PMS) generally involves:

  1. selecting roads for repair at random every single year
  2. designing one standard pavement section for every road
  3. monitoring condition data to prioritize maintenance
  4. collecting tolls from the vehicles using the network
Show answer & solution

Answer: (C) monitoring condition data to prioritize maintenance

A PMS supports maintenance decisions with condition data.

Question 18

A pavement condition index is generally derived from:

  1. the colour and surface texture of the pavement
  2. the aggregate size used in the surface layer
  3. the traffic volume carried by the section alone
  4. the type, extent and severity of distresses
Show answer & solution

Answer: (D) the type, extent and severity of distresses

Distress surveys are condensed into a single index of pavement condition.

Question 19

The International Roughness Index (IRI) is used to describe a pavement's:

  1. ride quality (surface roughness)
  2. structural thickness of the layers
  3. skid resistance of the surface
  4. drainage capacity of the shoulder
Show answer & solution

Answer: (A) ride quality (surface roughness)

IRI is a standard measure of longitudinal roughness in m/km.

Question 20

A preventive maintenance strategy generally:

  1. waits until the pavement has completely failed in service
  2. applies low-cost treatment while condition is fair
  3. repairs only the worst roads in the whole network first
  4. avoids all treatment until reconstruction falls due
Show answer & solution

Answer: (B) applies low-cost treatment while condition is fair

Preventive maintenance slows deterioration and is cheaper than late repair.

Question 21

Routine maintenance activities are important mainly to:

  1. widen the right-of-way for future traffic lanes
  2. change the functional class of the road network
  3. fix minor defects before they become costly
  4. increase the design speed of the highway section
Show answer & solution

Answer: (C) fix minor defects before they become costly

Routine maintenance includes patching, drain cleaning and vegetation control.

Question 22

Periodic maintenance, such as resurfacing, is carried out mainly to:

  1. renew the surface and keep water out
  2. replace the subgrade with a stronger material
  3. widen the carriageway to add more traffic lanes
  4. change the alignment to ease the sharp curves
Show answer & solution

Answer: (A) renew the surface and keep water out

Periodic maintenance is done at intervals of several years to renew the surface.

Question 23

Highway maintenance activities are commonly grouped as:

  1. survey, estimating and tendering of road works
  2. marking, signing and signalling of road users
  3. planning, design and construction of new roads
  4. routine, periodic and rehabilitation work
Show answer & solution

Answer: (D) routine, periodic and rehabilitation work

Treatments are matched to the level of deterioration.

Question 24

A rigid pavement mainly consists of:

  1. a layer of loose gravel on compacted earth
  2. a concrete slab carrying load by its stiffness
  3. a stone soling topped with water-bound macadam
  4. a thick bituminous surface on a granular base
Show answer & solution

Answer: (B) a concrete slab carrying load by its stiffness

Concrete slabs spread the load over a wide area through their stiffness.

Question 25

Joints are provided in rigid pavements mainly to:

  1. allow slab movement and control cracking
  2. drain water from beneath the sub-base layer
  3. raise the camber of the slab surface locally
  4. increase the skid resistance of the slab
Show answer & solution

Answer: (A) allow slab movement and control cracking

Joints give controlled places for slab movement.

Question 26

Contraction joints in a concrete pavement are intended to:

  1. allow the slab to expand freely in hot weather
  2. give a planned plane for shrinkage cracks
  3. carry the wheel load across the slab edge
  4. bond the slab firmly to the sub-base below
Show answer & solution

Answer: (B) give a planned plane for shrinkage cracks

Shrinkage and cooling shorten the slab, so joints make the cracks occur where planned.

Question 27

Expansion joints in a concrete pavement are provided to:

  1. hold adjacent slabs tightly together always
  2. strengthen the slab corners against heavy loading
  3. let water drain from beneath the slab quickly
  4. let slabs expand in hot weather without buckling
Show answer & solution

Answer: (D) let slabs expand in hot weather without buckling

A compressible filler in the joint accommodates thermal expansion.

Question 28

Dowel bars in a rigid pavement mainly serve to:

  1. provide drainage at the joint opening below the slab
  2. hold two adjacent slabs tightly together at the joint
  3. transfer part of the wheel load across the joint
  4. increase the effective slab thickness near the edges
Show answer & solution

Answer: (C) transfer part of the wheel load across the joint

Dowels give load transfer while permitting the joint to move.

Question 29

Tie bars in a rigid pavement mainly serve to:

  1. carry wheel loads across the transverse contraction joints
  2. hold adjacent lanes together so they cannot separate
  3. reduce the self-weight of the whole concrete slab
  4. allow free thermal expansion at the longitudinal joint
Show answer & solution

Answer: (B) hold adjacent lanes together so they cannot separate

Tie bars are deformed bars across longitudinal joints.

Question 30

Warping stresses in a concrete slab arise mainly from:

  1. wheel loads acting alone on the slab surface
  2. the spacing chosen for the dowel bars at joints
  3. a perfectly moisture-free subgrade beneath the slab
  4. a temperature difference through the slab depth
Show answer & solution

Answer: (D) a temperature difference through the slab depth

Differential temperature makes the slab curl, and the weight of the slab resists it.

Question 31

In Westergaard's analysis, the critical positions of a wheel load on a slab are:

  1. joint, shoulder and kerb
  2. corner, shoulder and kerb
  3. interior, edge and corner
  4. top, middle and bottom
Show answer & solution

Answer: (C) interior, edge and corner

Stresses are computed for loads at the interior, the edge and the corner of the slab.

Question 32

Westergaard's theory treats a concrete pavement slab as a:

  1. plate on an elastic, spring-like foundation
  2. simple beam on two rigid point supports
  3. flexible membrane stretched over a large void
  4. rigid block resting freely on steel rollers
Show answer & solution

Answer: (A) plate on an elastic, spring-like foundation

Subgrade support is represented by the modulus of subgrade reaction k.

Question 33

The modulus of subgrade reaction (k) is usually determined by:

  1. the CBR penetration test
  2. the Los Angeles abrasion test
  3. the bitumen penetration test
  4. a plate load test
Show answer & solution

Answer: (D) a plate load test

k is the pressure per unit deflection from a plate bearing test.

Question 34

Continuously Reinforced Concrete Pavement (CRCP) differs from jointed concrete pavement in that it:

  1. has dowels fitted at every contraction joint
  2. has no steel at all and no joints of any kind
  3. has continuous steel and no transverse joints
  4. has a thick bituminous concrete layer on top
Show answer & solution

Answer: (C) has continuous steel and no transverse joints

In CRCP, fine closely spaced cracks are held tight by the steel.

Question 35

Faulting in rigid pavements is mainly caused by:

  1. excess camber shedding water from the slab edge
  2. settlement or pumping with poor load transfer
  3. overuse of tie bars across the longitudinal joints
  4. too much skid resistance on the slab surface
Show answer & solution

Answer: (B) settlement or pumping with poor load transfer

Faulting is a step between adjacent slabs at a joint or crack.

Question 36

Pumping in a rigid pavement refers to the:

  1. ejection of water and fines from under the slab
  2. bleeding of excess binder at the slab surface
  3. planned injection of grout beneath the slab edges
  4. settlement of the subgrade under the shoulder
Show answer & solution

Answer: (A) ejection of water and fines from under the slab

Pumping removes support from under the slab and causes faulting.

Question 37

The concrete slab of a rigid pavement is normally placed on a:

  1. bed of bare rock only
  2. sub-base or prepared subgrade
  3. thick bituminous wearing course
  4. layer of soft clay
Show answer & solution

Answer: (B) sub-base or prepared subgrade

A sub-base gives uniform support and prevents pumping.

Question 38

Compared with flexible pavements, rigid pavements generally offer:

  1. lower stiffness and a shorter life in every case studied
  2. the same initial cost as flexible pavement in every case
  3. no need for any joints under any site conditions
  4. a stiffer response and often longer life at higher first cost
Show answer & solution

Answer: (D) a stiffer response and often longer life at higher first cost

Rigid pavements usually cost more initially but need less frequent maintenance.

Question 39

The choice between a flexible and a rigid pavement depends on factors such as:

  1. traffic, cost, materials, subgrade and climate
  2. the colour preference of road users in the area
  3. a random selection among available types
  4. the length of the shoulder on the road
Show answer & solution

Answer: (A) traffic, cost, materials, subgrade and climate

The choice is a technical and economic decision for each project.

Practice these 39 questions interactively →