Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Highway Engineering: Geometric Design: Curves & Hill Roads

Civil Engineering · Highway Engineering

27 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

The raising of the outer edge of the pavement above the inner edge on a horizontal curve is called:

  1. super-elevation
  2. longitudinal gradient
  3. carriageway widening
  4. transverse camber
Show answer & solution

Answer: (A) super-elevation

Super-elevation (also called cant or banking) is the transverse tilt given to the pavement on a curve.

Question 2

Super-elevation is provided on horizontal curves mainly to:

  1. lengthen the stopping sight distance available to drivers
  2. counteract part of the centrifugal force
  3. drain surface water off the central median faster
  4. ease the gradient along the whole curve
Show answer & solution

Answer: (B) counteract part of the centrifugal force

The tilt of the pavement produces a component of weight that opposes the outward centrifugal force.

Question 3

The super-elevation required on a curve depends mainly on:

  1. number of lanes and shoulder width provided on road
  2. traffic volume and surface texture of the road pavement
  3. curve radius, design speed and side friction
  4. pavement thickness and subgrade CBR value on site
Show answer & solution

Answer: (C) curve radius, design speed and side friction

Superelevation follows from e + f = V²/(127R), so it depends on speed and radius.

Question 4

The minimum radius of a horizontal curve is governed mainly by the:

  1. minimum camber and available sight distance
  2. length of transition curve and width of shoulders
  3. pavement thickness and design traffic volume
  4. maximum superelevation and side friction factor
Show answer & solution

Answer: (D) maximum superelevation and side friction factor

R_min = V²/[127(e_max + f_max)], where V is in km/h.

Question 5

Find the minimum radius of a horizontal curve for a design speed of 80 km/h, e = 0.07 and f = 0.15. (R = V²/127(e + f))

  1. about 187 m
  2. about 229 m
  3. about 115 m
  4. about 360 m
Show answer & solution

Answer: (B) about 229 m

R = 80²/(127 × 0.22) = 6400/27.94 ≈ 229 m.

Question 6

In the conventional design method for horizontal curves, super-elevation is calculated to balance the centrifugal force fully at:

  1. 75 percent of design speed, with friction neglected
  2. the 85th percentile speed, with friction neglected
  3. 50 percent of design speed, with friction neglected
  4. the full design speed, with friction included
Show answer & solution

Answer: (A) 75 percent of design speed, with friction neglected

Super-elevation is computed for 0.75V (three-fourths of the design speed) with friction neglected; side friction takes up the remaining effect at the full design speed.

Question 7

The maximum super-elevation on a horizontal curve is capped at a modest value (about 7 to 10 percent) mainly because a steeper cross-slope:

  1. is unsafe for slow-moving or stopped vehicles, which may slide towards the inside of the curve
  2. makes the curve radius impossible to calculate
  3. increases the design speed of the road
  4. removes the need for any side friction at all
Show answer & solution

Answer: (A) is unsafe for slow-moving or stopped vehicles, which may slide towards the inside of the curve

A very steep cross-fall is unsafe for slow or stationary vehicles, especially on slippery surfaces, so super-elevation is limited to a maximum value.

Question 8

For design of horizontal curves, the coefficient of lateral (side) friction between tyre and pavement is generally taken as about:

  1. 0.50
  2. 0.01
  3. 0.35
  4. 0.15
Show answer & solution

Answer: (D) 0.15

A design side-friction factor of about 0.15 is used, well below the actual available friction, to keep a margin of safety against skidding.

Question 9

If the super-elevation on a curve is much more than required, slow-moving vehicles tend to:

  1. skid towards the outer edge of the curve
  2. stall because of excess traction on the slope
  3. overturn about the outer wheels of the vehicle
  4. slide towards the inner edge of the curve
Show answer & solution

Answer: (D) slide towards the inner edge of the curve

At low speed the weight component down the slope exceeds the centrifugal force, pulling vehicles inward.

Question 10

On a horizontal curve that has no super-elevation, rutting and potholes are most likely to develop at the:

  1. centre
  2. outer edge
  3. uniform across the width
  4. inner edge
Show answer & solution

Answer: (B) outer edge

Without superelevation, vehicles push outward and the outer edge carries most of the load.

Question 11

Extra widening of the carriageway on horizontal curves is provided mainly to allow for:

  1. the added tractive resistance from a steeper gradient
  2. loss of friction on wet pavement surfaces
  3. off-tracking of rear wheels and driver clearance
  4. reduced sight distance on the sharp curve
Show answer & solution

Answer: (C) off-tracking of rear wheels and driver clearance

Extra width compensates for off-tracking (mechanical widening) and driver psychology (psychological widening).

Question 12

A transition curve between a straight and a circular curve is provided to:

  1. introduce curvature and super-elevation slowly
  2. eliminate the need for any extra widening there
  3. shorten the total length of the alignment
  4. reduce the radius of the circular curve sharply
Show answer & solution

Answer: (A) introduce curvature and super-elevation slowly

Transition curves give a gradual change in curvature, centrifugal force and superelevation.

Question 13

Which curve is widely used as a transition curve on highways?

  1. The reverse circular curve
  2. The spiral (clothoid)
  3. The compound circular curve
  4. The broken-back curve
Show answer & solution

Answer: (B) The spiral (clothoid)

A clothoid has curvature that increases uniformly with length, which gives an ideal transition.

Question 14

A maximum limit is placed on road gradients mainly so that:

  1. sight distance on curves is increased greatly
  2. the side drains can carry the water away quickly and easily
  3. heavy vehicles keep speed and braking stays safe
  4. the camber can be kept as small as possible
Show answer & solution

Answer: (C) heavy vehicles keep speed and braking stays safe

Steep grades slow heavy vehicles and make braking on descents difficult.

Question 15

Ruling gradient and limiting gradient differ in that:

  1. they are one and the same gradient, quoted under two names in different design codes
  2. ruling is the steepest permitted, limiting is the flattest used for drainage
  3. ruling applies only to hill roads, limiting applies only to plain terrain roads and highways
  4. ruling is the normal design maximum, limiting is steeper and used where ruling costs too much
Show answer & solution

Answer: (D) ruling is the normal design maximum, limiting is steeper and used where ruling costs too much

Limiting gradients are used in difficult terrain where adopting the ruling gradient would be too costly.

Question 16

The steepest gradient, permitted only for short stretches in extraordinary situations, is called the:

  1. exceptional gradient
  2. minimum drainage gradient
  3. average floating gradient
  4. ruling gradient for hills
Show answer & solution

Answer: (A) exceptional gradient

Exceptional gradients are used only for short lengths where there is no practical alternative.

Question 17

Exceptional gradients should not be provided over a continuous length exceeding:

  1. 20 m
  2. 100 m
  3. 50 m
  4. 10 m
Show answer & solution

Answer: (B) 100 m

Exceptional gradients are restricted to short stretches, not more than about 100 m at a time.

Question 18

The gradient that the designer adopts as the standard for a road section, and tries not to exceed in normal conditions, is called the:

  1. limiting gradient
  2. exceptional gradient
  3. minimum gradient
  4. ruling (design) gradient
Show answer & solution

Answer: (D) ruling (design) gradient

The ruling or design gradient is the maximum gradient adopted for the design of a road section; limiting and exceptional gradients are used only where terrain makes the ruling gradient uneconomical.

Question 19

A minimum longitudinal gradient is provided on flat road sections mainly for:

  1. improving the sight distance on the curves
  2. reducing fuel consumption of vehicles
  3. drainage of surface water along the road
  4. improving braking on long descents
Show answer & solution

Answer: (C) drainage of surface water along the road

A small gradient lets water flow along side drains instead of ponding.

Question 20

Grade compensation on hill road curves is provided to:

  1. reduce the gradient on a curve to offset curve resistance
  2. raise the outer edge of the curve for comfort
  3. increase the gradient on the curve to save earthwork cost
  4. widen the carriageway on the curve for off-tracking trucks
Show answer & solution

Answer: (A) reduce the gradient on a curve to offset curve resistance

Curves add tractive resistance, so the grade is eased to keep the effective grade within the ruling value.

Question 21

Hill road alignment requires special attention to:

  1. pavement colour, signage style and kerb detailing
  2. slope stability, geology and restricted curve standards
  3. wide medians and frequent signalised intersections
  4. the same factors as plain terrain, with no changes at all
Show answer & solution

Answer: (B) slope stability, geology and restricted curve standards

Mountain terrain brings slope-stability, geology and curvature constraints not found in plains.

Question 22

A hairpin bend on a hill road is:

  1. a sharp reversal of direction used to gain elevation
  2. a transition curve between a tangent and an arc
  3. a type of at-grade junction on mountain roads
  4. a gentle curve used to ease gradients in flat plains
Show answer & solution

Answer: (A) a sharp reversal of direction used to gain elevation

Hairpin bends turn the road through about 180° so it can climb steep hillsides.

Question 23

Sight distance at a hairpin bend is a particular problem because:

  1. super-elevation there is never provided on the bend
  2. the gradient there is always flat, so vehicles cannot see downhill
  3. sharp curvature and cut slopes block the view inside the bend
  4. traffic there is always heavy and moving very fast
Show answer & solution

Answer: (C) sharp curvature and cut slopes block the view inside the bend

Tight radius and hillside cuts on the inside restrict the line of sight.

Question 24

Extra widening on hill road curves is provided mainly to allow for:

  1. extra space needed for roadside drains and kerbs and walls
  2. vehicles stopping on the shoulders for long periods
  3. the wider bodies of vehicles travelling uphill on gradients
  4. greater off-tracking and manoeuvring difficulty on curves
Show answer & solution

Answer: (D) greater off-tracking and manoeuvring difficulty on curves

Sharp curves cause large off-tracking and make manoeuvring harder, so extra width is needed.

Question 25

Slope stability is a vital consideration for hill roads because:

  1. it governs the choice of bitumen grade for surfacing
  2. steep, complex slopes may fail and damage the road
  3. it determines the design axle load for the pavement
  4. it fixes the camber to be given to the road carriageway
Show answer & solution

Answer: (B) steep, complex slopes may fail and damage the road

Landslides and slips are major hazards on hill roads.

Question 26

Retaining and breast walls on hill roads are provided to:

  1. support unstable slopes and protect the road
  2. widen the carriageway for additional traffic lanes
  3. reduce the super-elevation needed on the sharp curves
  4. carry vehicle loads over culverts and drains
Show answer & solution

Answer: (A) support unstable slopes and protect the road

Walls hold back the earth on the hillside or support the road on the valley side.

Question 27

Rock-fall protection measures such as catch ditches and nets on hill roads are provided to:

  1. lower the skid resistance of the pavement surface layer
  2. drain surface water from the carriageway quickly
  3. protect road users from rocks falling from slopes above
  4. reduce the gradient of the road on the hillside
Show answer & solution

Answer: (C) protect road users from rocks falling from slopes above

Falling rock is a serious hazard where roads pass below steep rock slopes.

Practice these 27 questions interactively →