At-grade intersections are generally classified into types such as:
Show answer & solution
Answer: (B) T, cross and rotary intersections
Diamond, cloverleaf and trumpet are grade-separated interchanges, not at-grade intersections.
Civil Engineering · Highway Engineering
30 questions, each with the answer and a worked solution.
Practice interactively and track your score →At-grade intersections are generally classified into types such as:
Answer: (B) T, cross and rotary intersections
Diamond, cloverleaf and trumpet are grade-separated interchanges, not at-grade intersections.
The total number of conflict points at an unsignalized four-leg intersection of two two-way roads is:
Answer: (D) 32
There are 16 crossing, 8 merging and 8 diverging conflicts, totalling 32.
A four-leg roundabout reduces the number of conflict points to:
Answer: (A) 8
Crossing conflicts are replaced by 4 merging and 4 diverging points.
At a rotary (roundabout) intersection, vehicles:
Answer: (C) circulate one way around a central island
One-way circulation turns crossing conflicts into merging and diverging.
Compared with a conventional signalized intersection, a roundabout is often preferred because it can offer:
Answer: (A) fewer conflict points and lower conflict speeds
Roundabouts reduce severe crashes and avoid signal delay.
A grade-separated interchange is one in which:
Answer: (C) roads cross at different levels, linked by ramps
Vertical separation removes crossing conflicts.
Grade-separated interchanges are generally justified where:
Answer: (D) traffic is too heavy for an at-grade junction
Interchanges are expensive and are provided on high-volume, high-speed routes.
A cloverleaf interchange is characterized by:
Answer: (B) four loop ramps in the quadrants
The loops handle left turns without crossing conflicts.
A diamond interchange generally has:
Answer: (B) four ramps meeting the minor road at grade
Diamond interchanges are common where a freeway crosses a minor road.
A trumpet interchange is used at:
Answer: (D) three-leg (T) junctions
The trumpet provides all movements at a T-junction with one loop.
A weaving section is where:
Answer: (C) merging and diverging streams cross
Weaving needs adequate length for vehicles to change lanes.
The type of intersection or interchange for a location is selected considering:
Answer: (A) traffic, land, cost and road importance
The choice balances capacity, safety, cost and site constraints.
Channelization at an intersection mainly:
Answer: (C) guides vehicles into set paths, cutting conflicts
Channelizing islands separate movements and reduce the area of conflict.
Pedestrian safety at crossings is improved by:
Answer: (D) marked crossings, lighting and refuge islands
Pedestrians need clear, visible and protected crossing places.
A road safety audit at the design stage is valuable mainly because:
Answer: (B) early fixes cost less than later retrofits
Early safety review prevents costly retrofits.
A road safety audit is:
Answer: (A) an independent review to find safety problems
Audits are carried out by a team independent from the designers.
Accident (crash) data analysis is used mainly to:
Answer: (C) find high-accident sites and their causes
Crash records show where and why accidents occur.
A black spot (accident hotspot) is a location where:
Answer: (A) crashes are unusually frequent or severe
Black spots are identified from accident data and given priority for safety measures.
The concept of 'forgiving roadside' recognizes that:
Answer: (D) some vehicles will leave the road, so keep sides safe
A forgiving roadside reduces the severity of run-off-road crashes.
A clear zone is:
Answer: (B) an obstacle-free recovery area beside the road
It gives an errant vehicle room to recover or stop.
Guardrails (crash barriers) mainly:
Answer: (A) redirect errant vehicles and cut crash severity
They are used where hitting a fixed object or a steep slope would be worse than hitting the barrier.
Median barriers mainly:
Answer: (C) stop vehicles crossing into opposing traffic
They prevent head-on crashes on divided highways.
Rumble strips are used mainly to:
Answer: (D) alert drowsy drivers by noise and vibration
Rumble strips on shoulders and centre lines warn of lane departure.
School zone safety measures are important mainly because:
Answer: (B) children are vulnerable and need slow speeds
Children are more at risk and less predictable in traffic.
Bus bays (lay-bys) serve mainly to:
Answer: (A) let buses stop off the through lanes
Buses stopping in a bay do not block the traffic lane.
Bicycle facilities are provided mainly to:
Answer: (D) give cyclists a safer space away from cars
Segregation reduces conflicts between cyclists and motor vehicles.
Noise barriers along a highway mainly serve to:
Answer: (C) cut traffic noise reaching nearby land uses
They block or absorb sound travelling toward sensitive areas.
Weather-related hazards such as fog, ice and heavy rain require special attention because they:
Answer: (B) reduce safety and need design and operational measures
Warning signs, drainage, de-icing and fog lights help to manage them.
Winter maintenance activities such as snow clearance and de-icing are carried out mainly to:
Answer: (A) keep roads passable and safe in snow and ice
Winter operations keep mountain and northern roads open.
Inspection and maintenance of bridges is important mainly because:
Answer: (B) early defect detection protects safety and assets
Regular inspection finds defects before they become failures.