Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Rock Mechanics & Ground Control: Subsidence

Mining Engineering · Rock Mechanics & Ground Control

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is mining subsidence?

  1. Upward movement of the ground caused by blasting
  2. Erosion of the surface by rain
  3. Downward movement of the ground surface caused by underground extraction
  4. Flooding of mine workings
Show answer & solution

Answer: (C) Downward movement of the ground surface caused by underground extraction

Removal of ore or coal allows overlying strata to move into the void.

Question 2

Which type of subsidence produces a smooth, broad depression over longwall panels?

  1. Sinkhole (pit) subsidence
  2. Floor heave
  3. Trough (continuous) subsidence
  4. Plug subsidence
Show answer & solution

Answer: (C) Trough (continuous) subsidence

Total extraction produces a continuous trough at the surface.

Question 3

Which type of subsidence forms abrupt holes over shallow room and pillar workings?

  1. Regional subsidence
  2. Sinkhole (pit) subsidence
  3. Ground heave
  4. Trough subsidence
Show answer & solution

Answer: (B) Sinkhole (pit) subsidence

Roof collapse migrates upward to the surface over shallow voids.

Question 4

What is the angle of draw?

  1. Angle of break
  2. Angle of repose of goaf material
  3. Dip of the coal seam
  4. Angle between the vertical and the line from the panel edge to the limit of surface subsidence
Show answer & solution

Answer: (D) Angle between the vertical and the line from the panel edge to the limit of surface subsidence

The angle of draw defines how far outside the panel the surface is affected.

Question 5

What angle of draw is commonly used in UK National Coal Board subsidence practice?

  1. About 5°
  2. About 35°
  3. About 60°
  4. About 85°
Show answer & solution

Answer: (B) About 35°

The NCB Subsidence Engineers' Handbook uses an angle of draw of about 35°.

Question 6

What does critical width mean in subsidence engineering?

  1. The panel width at which full possible subsidence is first reached at one surface point
  2. The minimum width of a pillar
  3. The width of a shaft pillar
  4. The width of a roadway
Show answer & solution

Answer: (A) The panel width at which full possible subsidence is first reached at one surface point

Panels narrower than critical width give less than maximum subsidence.

Question 7

What happens to surface subsidence when the panel width is less than the critical width?

  1. Subsidence equals the critical value
  2. There is no subsidence at all
  3. Subsidence exceeds the seam thickness
  4. Maximum subsidence is less than the full possible value
Show answer & solution

Answer: (D) Maximum subsidence is less than the full possible value

Sub-critical panels allow the overburden to bridge partially.

Question 8

What is the approximate critical width for full subsidence in UK practice?

  1. About 0.1 times the depth
  2. About 1.4 times the depth
  3. About 5 times the depth
  4. About 10 times the depth
Show answer & solution

Answer: (B) About 1.4 times the depth

With a 35° angle of draw, critical width = 2h tan 35° ≈ 1.4h.

Question 9

What is the subsidence factor?

  1. Ratio of maximum surface subsidence to extracted seam thickness
  2. Ratio of tilt to strain
  3. Ratio of depth to seam thickness
  4. Ratio of panel width to depth
Show answer & solution

Answer: (A) Ratio of maximum surface subsidence to extracted seam thickness

Subsidence factor a = Smax/m.

Question 10

What is the typical maximum subsidence over a fully caved, supercritical longwall panel?

  1. About 0.1 times the seam thickness
  2. About 0.9 times the seam thickness
  3. About 2 times the seam thickness
  4. About 5 times the seam thickness
Show answer & solution

Answer: (B) About 0.9 times the seam thickness

Bulking of caved rock keeps subsidence slightly below the extracted thickness.

Question 11

How does backfilling (stowing) the goaf affect subsidence?

  1. It causes ground uplift
  2. It has no effect
  3. It greatly reduces subsidence
  4. It increases subsidence
Show answer & solution

Answer: (C) It greatly reduces subsidence

Hydraulic sand stowing can reduce subsidence to about 5–25% of seam thickness.

Question 12

Which surface deformations caused by subsidence produce the most damage to buildings?

  1. Ground noise
  2. Changes in soil colour
  3. Uniform vertical lowering
  4. Horizontal strain (tension and compression) and tilt
Show answer & solution

Answer: (D) Horizontal strain (tension and compression) and tilt

Uniform lowering does little harm; differential movement and strain crack structures.

Question 13

Where does the maximum tensile strain occur in a subsidence trough?

  1. Exactly above the panel centre
  2. Far outside the angle of draw
  3. Near the outer margin of the trough, outside the panel edge
  4. At the centre of the trough
Show answer & solution

Answer: (C) Near the outer margin of the trough, outside the panel edge

The convex outer zone is in tension.

Question 14

Where does the maximum compressive strain occur in a subsidence trough?

  1. Inside the trough between the panel edge and the centre
  2. Far outside the panel
  3. At the outer limit of the trough
  4. At the shaft
Show answer & solution

Answer: (A) Inside the trough between the panel edge and the centre

The concave inner part of the trough is in compression.

Question 15

What is the angle from the vertical of the line joining the panel edge to the point of maximum tensile strain called?

  1. Angle of draw
  2. Dip angle
  3. Angle of break
  4. Angle of repose
Show answer & solution

Answer: (C) Angle of break

The angle of break is smaller than the angle of draw.

Question 16

Which empirical subsidence prediction method was published by the UK National Coal Board?

  1. Subsidence Engineers' Handbook (SEH) method
  2. Q-system
  3. Kirsch method
  4. Hoek–Brown method
Show answer & solution

Answer: (A) Subsidence Engineers' Handbook (SEH) method

The SEH (1966, 1975) gives subsidence profiles from width, depth and seam thickness.

Question 17

Which subsidence prediction method sums the effects of many small extraction elements using a mathematical function?

  1. Kirsch method
  2. Profile function method
  3. Bishop method
  4. Influence function method (e.g., Knothe)
Show answer & solution

Answer: (D) Influence function method (e.g., Knothe)

Each element contributes a bell-shaped influence on the surface.

Question 18

Which mining technique arranges the faces of longwall panels to reduce strains under sensitive surface structures?

  1. Block caving
  2. Harmonic mining
  3. Bord and pillar mining
  4. Retreat mining
Show answer & solution

Answer: (B) Harmonic mining

Harmonic mining cancels tensile and compressive strains by careful face layout.

Question 19

What is partial extraction as a subsidence control measure?

  1. Leaving pillars to support the overburden and limit surface movement
  2. Filling with sand
  3. Allowing full caving
  4. Mining the full seam
Show answer & solution

Answer: (A) Leaving pillars to support the overburden and limit surface movement

Partial extraction (e.g., narrow panels and wide pillars) reduces subsidence.

Question 20

What is the coal or ore left unmined beneath important surface structures to protect them called?

  1. Harmonic panel
  2. Stowed pillar
  3. Protective (support) pillar
  4. Caved zone
Show answer & solution

Answer: (C) Protective (support) pillar

Protective pillars are sized using the angle of draw from the structure.

Question 21

How does the depth of mining affect the maximum surface strain for a given seam thickness?

  1. Strain becomes zero at shallow depth
  2. Depth has no effect
  3. Strain increases as depth increases
  4. Strain decreases as depth increases
Show answer & solution

Answer: (D) Strain decreases as depth increases

Strain is roughly proportional to seam thickness divided by depth.

Question 22

Which surface effect of subsidence is often seen on farmland and water courses?

  1. Ponding and changes in drainage
  2. Rise of the ground surface
  3. Volcanic activity
  4. Snow accumulation
Show answer & solution

Answer: (A) Ponding and changes in drainage

Subsidence troughs can collect water and reverse stream gradients.

Question 23

What is the surface movement that continues for some time after mining stops called?

  1. Instantaneous subsidence
  2. Residual subsidence
  3. First weighting
  4. Coal bump
Show answer & solution

Answer: (B) Residual subsidence

Residual subsidence comes from slow compaction of goaf and strata.

Question 24

Which satellite technique can map subsidence over large areas with millimetre accuracy?

  1. Prismatic compass surveying
  2. Plane table surveying
  3. Chain surveying
  4. InSAR (radar interferometry)
Show answer & solution

Answer: (D) InSAR (radar interferometry)

InSAR compares radar images taken at different times.

Question 25

What is the surface movement that travels ahead of and with an advancing longwall face called?

  1. Floor heave
  2. Rock burst
  3. Dynamic (travelling) subsidence
  4. Residual subsidence
Show answer & solution

Answer: (C) Dynamic (travelling) subsidence

The subsidence wave moves across the surface as the face advances.

Question 26

What is chimney (plug) subsidence?

  1. Collapse of a shaft lining
  2. A gradual broad trough
  3. Upward migration of collapse from a shallow opening to the surface
  4. Uplift of the surface
Show answer & solution

Answer: (C) Upward migration of collapse from a shallow opening to the surface

Chimney caving forms a vertical collapse pipe that can open at the surface.

Question 27

In which mining method is surface subsidence accepted as part of the method?

  1. Shrinkage stoping with backfill
  2. Cut and fill stoping
  3. Room and pillar with permanent pillars
  4. Block caving
Show answer & solution

Answer: (D) Block caving

Caving methods deliberately allow the overburden to collapse.

Question 28

Which mitigation measure involves digging trenches around buildings to absorb compressive ground strain?

  1. Pre-splitting
  2. Compressible trenches
  3. Slope drainage
  4. Hydraulic stowing
Show answer & solution

Answer: (B) Compressible trenches

Trenches filled with compressible material absorb ground compression.

Question 29

What surface feature forms when an underground void in salt, limestone or old shallow workings collapses?

  1. Sinkhole
  2. Fold
  3. Dyke
  4. Fault
Show answer & solution

Answer: (A) Sinkhole

Sinkholes are closed depressions formed by collapse into voids below.

Question 30

Below about what ratio of cover depth to extracted height is sinkhole risk over old room and pillar workings high?

  1. About 0.1
  2. About 10
  3. About 100
  4. About 1000
Show answer & solution

Answer: (B) About 10

Bulking of collapsed roof usually chokes caving before the surface when depth exceeds about 10 times the height.

Question 31

Why does caved rock eventually fill the void and stop upward caving?

  1. Broken rock occupies more volume than intact rock (bulking)
  2. Gas pressure supports the roof
  3. Water fills the void
  4. Caved rock compacts to a smaller volume
Show answer & solution

Answer: (A) Broken rock occupies more volume than intact rock (bulking)

The bulked rock supports the strata above and caving stops.

Question 32

What is the typical bulking factor of caved rock?

  1. 0.5
  2. 1.2 to 1.5
  3. 3.0
  4. 10
Show answer & solution

Answer: (B) 1.2 to 1.5

Broken rock usually occupies about 20–50% more volume than in place.

Question 33

How does the angle of draw in strong overburden compare with that in weak overburden?

  1. It is larger
  2. It is the same
  3. It is smaller
  4. It is zero
Show answer & solution

Answer: (C) It is smaller

Weak, soft overburden spreads movement over a wider area, giving a larger angle of draw.

Question 34

Which subsidence component is the change in horizontal displacement divided by the distance between two points?

  1. Tilt
  2. Curvature
  3. Vertical subsidence
  4. Horizontal strain
Show answer & solution

Answer: (D) Horizontal strain

Horizontal strain is expressed in mm/m and causes cracking or crushing.

Question 35

What is tilt in subsidence engineering?

  1. Horizontal strain between two points
  2. Total vertical subsidence
  3. Angle of draw
  4. Difference in subsidence between two points divided by their horizontal distance
Show answer & solution

Answer: (D) Difference in subsidence between two points divided by their horizontal distance

Tilt (slope) affects drainage, sewers and tall structures.

Question 36

What shape of subsidence trough does supercritical width extraction produce at the centre?

  1. A flat-bottomed trough at maximum subsidence
  2. Uplift at the centre
  3. A single sharp point
  4. No subsidence at the centre
Show answer & solution

Answer: (A) A flat-bottomed trough at maximum subsidence

When width exceeds critical width, the centre reaches maximum subsidence over a flat area.

Practice these 36 questions interactively →