Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Rock Mechanics & Ground Control: Rock Properties

Mining Engineering · Rock Mechanics & Ground Control

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which property of rock is defined as the ratio of the volume of voids to the total volume of the rock?

  1. Degree of saturation
  2. Permeability
  3. Void ratio
  4. Porosity
Show answer & solution

Answer: (D) Porosity

Porosity n = Vv/V; void ratio is the volume of voids divided by the volume of solids.

Question 2

What is the usual ratio of the tensile strength of rock to its uniaxial compressive strength?

  1. About 1/1
  2. About 1/10
  3. About 1/100
  4. About 1/2
Show answer & solution

Answer: (B) About 1/10

Rocks are weak in tension; tensile strength is commonly one-tenth to one-twentieth of the UCS.

Question 3

Which laboratory test is used to determine the indirect tensile strength of a rock core disc?

  1. Slake durability test
  2. Triaxial test
  3. Brazilian test
  4. Point load test
Show answer & solution

Answer: (C) Brazilian test

In the Brazilian test a disc is loaded across its diameter until it splits in tension.

Question 4

What is the formula for tensile strength in the Brazilian test, where P is failure load, D is disc diameter and t is disc thickness?

  1. 2P/(πDt)
  2. P/(πDt)
  3. 4P/(πD²)
  4. P/(Dt)
Show answer & solution

Answer: (A) 2P/(πDt)

The ISRM relation for the Brazilian disc test is σt = 2P/(πDt).

Question 5

Which field index test estimates rock strength by loading core or irregular lumps between two conical platens?

  1. Uniaxial compression test
  2. Brazilian test
  3. Schmidt hammer test
  4. Point load test
Show answer & solution

Answer: (D) Point load test

The point load test gives the index Is(50), which correlates with uniaxial compressive strength.

Question 6

Approximately how many times the point load index Is(50) is the uniaxial compressive strength of a rock?

  1. 2 to 5
  2. 20 to 25
  3. 50 to 60
  4. 100 to 120
Show answer & solution

Answer: (B) 20 to 25

The common empirical correlation is UCS ≈ 20–25 × Is(50).

Question 7

Which portable instrument estimates rock surface hardness from the rebound of a spring-driven mass?

  1. Shore scleroscope
  2. Abney level
  3. Schmidt hammer
  4. Point load tester
Show answer & solution

Answer: (C) Schmidt hammer

The Schmidt rebound hammer (L-type for rock) gives a rebound number related to strength.

Question 8

What length-to-diameter ratio does ISRM recommend for rock cores in the uniaxial compressive strength test?

  1. 0.5
  2. 1.0
  3. 2.5 to 3.0
  4. 5.0 to 6.0
Show answer & solution

Answer: (C) 2.5 to 3.0

ISRM suggests an L/D ratio of 2.5 to 3.0 to reduce end effects.

Question 9

Which test measures the resistance of shales and other weak rocks to disintegration under cycles of wetting and drying?

  1. Slake durability test
  2. Brazilian test
  3. Los Angeles abrasion test
  4. Point load test
Show answer & solution

Answer: (A) Slake durability test

Franklin's slake durability test rotates samples in a water-filled drum and gives the index Id2.

Question 10

Which elastic constant of rock is the ratio of lateral strain to axial strain under uniaxial loading?

  1. Poisson's ratio
  2. Shear modulus
  3. Bulk modulus
  4. Young's modulus
Show answer & solution

Answer: (A) Poisson's ratio

Poisson's ratio is lateral strain divided by axial strain.

Question 11

What is the typical range of Poisson's ratio for most intact rocks?

  1. 0.01 to 0.05
  2. 0.15 to 0.35
  3. 0.5 to 0.7
  4. 0.8 to 1.0
Show answer & solution

Answer: (B) 0.15 to 0.35

Most intact rocks have Poisson's ratio between about 0.15 and 0.35.

Question 12

Which modulus is the slope of a tangent drawn to the stress–strain curve at 50% of the peak strength?

  1. Secant modulus
  2. Initial modulus
  3. Bulk modulus
  4. Tangent modulus
Show answer & solution

Answer: (D) Tangent modulus

ISRM defines the tangent Young's modulus at 50% of the uniaxial compressive strength.

Question 13

How is the dynamic Young's modulus of rock usually determined in the laboratory?

  1. From the Brazilian test
  2. From ultrasonic P-wave and S-wave velocities
  3. From the Schmidt rebound number
  4. From the slake durability test
Show answer & solution

Answer: (B) From ultrasonic P-wave and S-wave velocities

Dynamic elastic constants are calculated from measured wave velocities and density.

Question 14

Why is the dynamic modulus of a rock usually higher than its static modulus?

  1. Rapid small-strain wave loading does not close cracks or cause creep
  2. Wave tests heat the rock
  3. Wave tests use larger specimens
  4. Static tests use only saturated cores
Show answer & solution

Answer: (A) Rapid small-strain wave loading does not close cracks or cause creep

Static loading closes microcracks and produces larger strains, so the static modulus is lower.

Question 15

What does the post-peak part of a complete stress–strain curve of rock describe?

  1. Crack closure at low stress
  2. Purely elastic behaviour
  3. Strain-softening behaviour after peak strength
  4. Creep under constant load
Show answer & solution

Answer: (C) Strain-softening behaviour after peak strength

After the peak, strength falls with further strain; this is the strain-softening region.

Question 16

Why is a stiff or servo-controlled testing machine needed to obtain the complete stress–strain curve of rock?

  1. To keep the specimen saturated
  2. To shorten the test duration
  3. To increase the rock strength
  4. To prevent violent failure caused by release of energy stored in the machine
Show answer & solution

Answer: (D) To prevent violent failure caused by release of energy stored in the machine

A soft machine releases stored elastic energy into the specimen at peak, causing explosive failure.

Question 17

Which classification of intact rock uses both uniaxial compressive strength and the modulus ratio?

  1. RMR classification
  2. Deere–Miller classification
  3. Protodyakonov classification
  4. Q-system
Show answer & solution

Answer: (B) Deere–Miller classification

Deere and Miller (1966) classified intact rock by UCS and the ratio of modulus to UCS.

Question 18

What does Protodyakonov's strength coefficient f approximately equal for a rock?

  1. Uniaxial compressive strength in MPa multiplied by 10
  2. RQD divided by 10
  3. Tensile strength in MPa
  4. Uniaxial compressive strength in MPa divided by 10
Show answer & solution

Answer: (D) Uniaxial compressive strength in MPa divided by 10

Protodyakonov's hardness coefficient f is roughly σc (MPa)/10.

Question 19

What is the time-dependent deformation of rock under constant stress called?

  1. Relaxation
  2. Fatigue
  3. Creep
  4. Dilation
Show answer & solution

Answer: (C) Creep

Creep is continued strain at constant stress; relaxation is the fall of stress at constant strain.

Question 20

Which rock type is most prone to creep, making it important in salt mines such as Khewra?

  1. Rock salt
  2. Granite
  3. Quartzite
  4. Basalt
Show answer & solution

Answer: (A) Rock salt

Evaporites such as rock salt deform plastically and creep markedly even at moderate stress.

Question 21

What is the increase in volume of rock during shearing or close to failure called?

  1. Creep
  2. Consolidation
  3. Swelling
  4. Dilatancy
Show answer & solution

Answer: (D) Dilatancy

Opening of cracks near peak stress causes volume increase called dilatancy.

Question 22

Which property expresses the ease with which water flows through a rock mass?

  1. Permeability
  2. Porosity
  3. Density
  4. Hardness
Show answer & solution

Answer: (A) Permeability

Permeability (hydraulic conductivity) controls flow; a porous rock can still have low permeability.

Question 23

What unit weight of rock is commonly assumed when estimating the vertical in-situ stress?

  1. About 10 kN/m³
  2. About 18 kN/m³
  3. About 27 kN/m³
  4. About 50 kN/m³
Show answer & solution

Answer: (C) About 27 kN/m³

Average rock unit weight of about 27 kN/m³ gives σv ≈ 0.027 MPa per metre of depth.

Question 24

What is the approximate vertical in-situ stress at a depth of 1000 m in average rock?

  1. 0.27 MPa
  2. 2.7 MPa
  3. 27 MPa
  4. 270 MPa
Show answer & solution

Answer: (C) 27 MPa

σv = γh ≈ 0.027 × 1000 = 27 MPa.

Question 25

Which in-situ stress measurement method pressurises a sealed section of a borehole until a fracture forms?

  1. Doorstopper method
  2. Hydraulic fracturing
  3. Overcoring
  4. Flat jack method
Show answer & solution

Answer: (B) Hydraulic fracturing

Breakdown and shut-in pressures in hydraulic fracturing give the minimum and maximum horizontal stresses.

Question 26

Which in-situ stress measurement method relieves stress around a strain cell by drilling a larger concentric hole?

  1. Plate load test
  2. Overcoring
  3. Hydraulic fracturing
  4. Flat jack method
Show answer & solution

Answer: (B) Overcoring

Overcoring measures strain recovery when a strain cell (e.g., CSIRO HI cell) is cut free from the rock.

Question 27

What does the stress ratio K represent in rock mechanics?

  1. Ratio of average horizontal stress to vertical stress
  2. Ratio of porosity to void ratio
  3. Ratio of length to diameter of a core
  4. Ratio of tensile to compressive strength
Show answer & solution

Answer: (A) Ratio of average horizontal stress to vertical stress

K = σh/σv; measurements show K is often greater than 1 at shallow depth.

Question 28

According to elastic theory, what is the horizontal-to-vertical stress ratio K for laterally confined rock with Poisson's ratio ν?

  1. (1−ν)/ν
  2. 1/ν
  3. ν/(1+ν)
  4. ν/(1−ν)
Show answer & solution

Answer: (D) ν/(1−ν)

With no lateral strain, σh = [ν/(1−ν)]σv (Terzaghi and Richart).

Question 29

Which effect causes larger rock specimens to show lower strength than small specimens?

  1. Creep effect
  2. Shape effect
  3. Size effect
  4. End effect
Show answer & solution

Answer: (C) Size effect

Larger specimens contain more flaws, so their strength is lower.

Question 30

What causes the end effect in uniaxial compression testing of rock cores?

  1. Friction between the loading platens and the specimen ends
  2. Moisture in the specimen
  3. The diameter of the specimen
  4. The loading rate
Show answer & solution

Answer: (A) Friction between the loading platens and the specimen ends

Platen friction confines the ends and raises measured strength in short specimens.

Question 31

How does water saturation generally affect the uniaxial compressive strength of rock?

  1. It greatly increases the strength
  2. It reduces the strength
  3. It has no effect
  4. It doubles the strength
Show answer & solution

Answer: (B) It reduces the strength

Water weakens rock by reducing surface energy and through pore pressure, especially in shales and sandstones.

Question 32

Which rock property is measured by the Cerchar abrasivity index?

  1. Porosity
  2. Swelling potential
  3. Permeability
  4. Abrasiveness to drill bits and cutters
Show answer & solution

Answer: (D) Abrasiveness to drill bits and cutters

The CAI test scratches a steel pin across rock; wear of the pin indicates abrasivity.

Question 33

Which of these rocks generally has the highest uniaxial compressive strength?

  1. Shale
  2. Rock salt
  3. Quartzite
  4. Coal
Show answer & solution

Answer: (C) Quartzite

Quartzite commonly exceeds 150 MPa, while shale, salt and coal are much weaker.

Question 34

Which seismic wave travels fastest through a rock mass?

  1. P-wave (compressional wave)
  2. S-wave (shear wave)
  3. Rayleigh wave
  4. Love wave
Show answer & solution

Answer: (A) P-wave (compressional wave)

P-waves are the fastest body waves and arrive first.

Question 35

What is the sudden violent failure of highly stressed brittle rock in deep mines called?

  1. Creep
  2. Rock fall
  3. Floor heave
  4. Rock burst
Show answer & solution

Answer: (D) Rock burst

A rock burst is a sudden release of strain energy that ejects rock into the opening.

Question 36

What is the upward movement of weak floor strata into a roadway called?

  1. Rib spalling
  2. Floor heave
  3. Roof sag
  4. Rock burst
Show answer & solution

Answer: (B) Floor heave

Soft fireclay or mudstone floors squeeze up under pillar or side-wall stress, causing floor heave.

Practice these 36 questions interactively →