Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Rock Mechanics & Ground Control: Roof Support and Strata Control

Mining Engineering · Rock Mechanics & Ground Control

37 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the main function of rock bolts in underground mines?

  1. To reinforce the rock mass so that it supports itself
  2. To drain water
  3. To carry the full overburden like props
  4. To ventilate the roadway
Show answer & solution

Answer: (A) To reinforce the rock mass so that it supports itself

Bolts mobilise the strength of the rock mass rather than carrying dead load.

Question 2

Which rock bolting mechanism binds thin laminated roof layers together to act as one thicker beam?

  1. Friction anchoring
  2. Beam building
  3. Suspension
  4. Keying
Show answer & solution

Answer: (B) Beam building

Clamped layers act as a composite beam with higher stiffness and strength.

Question 3

Which rock bolting mechanism hangs a weak immediate roof from a stronger bed above?

  1. Beam building
  2. Suspension
  3. Keying
  4. Arching
Show answer & solution

Answer: (B) Suspension

Bolts anchored in competent strata hold up the weak layer below.

Question 4

Which rock bolt is anchored only at the top of the hole by an expansion shell?

  1. Fully grouted resin bolt
  2. Split set
  3. Mechanical point-anchored bolt
  4. Swellex bolt
Show answer & solution

Answer: (C) Mechanical point-anchored bolt

An expansion shell grips the hole wall at the end of the bolt; the bolt is then tensioned.

Question 5

Which rock bolt is a slotted steel tube that grips the hole wall by friction along its full length?

  1. Resin bolt
  2. Expansion shell bolt
  3. Cable bolt
  4. Split set
Show answer & solution

Answer: (D) Split set

Split sets are pushed into a slightly smaller hole and hold by radial spring force.

Question 6

Which friction rock bolt is expanded inside the hole by high-pressure water?

  1. Swellex bolt
  2. Split set
  3. Cone bolt
  4. Resin bolt
Show answer & solution

Answer: (A) Swellex bolt

The folded steel tube of a Swellex bolt inflates against the hole wall.

Question 7

Which bolt type gives the stiffest and most corrosion-resistant reinforcement?

  1. Wooden dowel
  2. Fully grouted resin bolt
  3. Mechanical point-anchored bolt
  4. Split set
Show answer & solution

Answer: (B) Fully grouted resin bolt

Full-column resin bonds the bar to the rock along its whole length and protects the steel.

Question 8

Which long, flexible support element made of steel strands is used to reinforce large stopes and wide intersections?

  1. Cable bolt
  2. Timber prop
  3. Timber chock
  4. Split set
Show answer & solution

Answer: (A) Cable bolt

Cable bolts can be 5–25 m long and are grouted into the rock.

Question 9

What is shotcrete?

  1. A cement grout for bolts
  2. A timber support
  3. Concrete sprayed pneumatically onto a rock surface
  4. A type of steel set
Show answer & solution

Answer: (C) Concrete sprayed pneumatically onto a rock surface

Shotcrete seals the surface and provides immediate support.

Question 10

Why are steel fibres added to shotcrete?

  1. To reduce its weight
  2. To make it set faster
  3. To change its colour
  4. To increase toughness and strength after cracking
Show answer & solution

Answer: (D) To increase toughness and strength after cracking

Fibres let shotcrete carry load after cracking and can replace mesh.

Question 11

What is the main purpose of welded wire mesh installed with rock bolts?

  1. To improve ventilation
  2. To carry the full overburden load
  3. To drain water
  4. To hold small loose rock pieces between the bolts
Show answer & solution

Answer: (D) To hold small loose rock pieces between the bolts

Mesh contains loose rock that would otherwise fall between bolts.

Question 12

Which steel support is designed to slide at its overlapping joints in roadways with large deformation?

  1. Hydraulic prop
  2. Split set
  3. Yielding steel arch (TH arch)
  4. Rigid I-beam set
Show answer & solution

Answer: (C) Yielding steel arch (TH arch)

Toussaint–Heintzmann arches yield in a controlled way at clamped joints.

Question 13

What is the main advantage of yielding supports in squeezing ground?

  1. They are lighter than timber
  2. They allow controlled deformation without failing
  3. They are always cheaper
  4. They prevent all ground movement
Show answer & solution

Answer: (B) They allow controlled deformation without failing

Allowing some convergence lowers the rock load on the support.

Question 14

Which hydraulic support is used along the face of a modern longwall?

  1. Powered roof support (shield)
  2. Timber prop
  3. Steel arch
  4. Rock bolt
Show answer & solution

Answer: (A) Powered roof support (shield)

Shields support the roof and advance with the face conveyor.

Question 15

Which type of powered support is most widely used on modern longwall faces?

  1. Two-leg shield
  2. Four-leg chock
  3. Frame support
  4. Single hydraulic prop
Show answer & solution

Answer: (A) Two-leg shield

Two-leg shields give good canopy-tip load and protection against goaf flushing.

Question 16

What is the caved area left behind a longwall face or after depillaring called?

  1. Abutment
  2. Goaf (gob)
  3. Barrier
  4. Bord
Show answer & solution

Answer: (B) Goaf (gob)

The goaf is the broken, caved zone where coal has been extracted.

Question 17

What is the regular caving of the main roof behind an advancing longwall face called?

  1. Spalling
  2. Rock burst
  3. Floor heave
  4. Periodic weighting
Show answer & solution

Answer: (D) Periodic weighting

After first caving, the main roof breaks at intervals, causing periodic load peaks on supports.

Question 18

What is the first major caving of the main roof after a longwall panel starts called?

  1. Coal bump
  2. Periodic weighting
  3. First (main) weighting
  4. Creep
Show answer & solution

Answer: (C) First (main) weighting

The first weighting occurs once the main roof span becomes too large to stand.

Question 19

Which zones form in the overburden above a longwall goaf, from the seam upwards?

  1. Continuous deformation zone, fractured zone, caved zone
  2. Elastic zone, plastic zone, caved zone
  3. Caved zone, fractured zone, continuous deformation zone
  4. Fractured zone, caved zone, soil zone
Show answer & solution

Answer: (C) Caved zone, fractured zone, continuous deformation zone

Movement and fracturing decrease upward from the caved zone to the surface.

Question 20

What is the weak strata directly above a coal seam that falls soon after support is removed called?

  1. Overburden
  2. Immediate roof
  3. Floor
  4. Main roof
Show answer & solution

Answer: (B) Immediate roof

The immediate roof caves readily behind the supports into the goaf.

Question 21

What is the strong, thick strata above the immediate roof that bends and breaks at intervals called?

  1. Main roof
  2. Immediate roof
  3. Floor
  4. False roof
Show answer & solution

Answer: (A) Main roof

Main roof behaviour controls first and periodic weighting.

Question 22

What is a thin layer of weak material directly above the seam that falls with the coal during mining called?

  1. Seat earth
  2. Main roof
  3. Immediate roof
  4. False roof
Show answer & solution

Answer: (D) False roof

False roof is often carbonaceous shale only a few centimetres thick.

Question 23

Which instrument shows roof sag or separation between strata layers in a roadway?

  1. Anemometer
  2. Piezometer
  3. Theodolite
  4. Telltale (roof extensometer)
Show answer & solution

Answer: (D) Telltale (roof extensometer)

Telltales have indicators anchored at different heights to show bed separation.

Question 24

Which instrument measures the load on a rock bolt?

  1. Piezometer
  2. Load cell
  3. Inclinometer
  4. Abney level
Show answer & solution

Answer: (B) Load cell

Hydraulic or electrical load cells under the bolt plate show bolt load.

Question 25

What does a pull test on a rock bolt determine?

  1. The anchorage capacity of the bolt
  2. The gas content
  3. The water inflow
  4. The rock's UCS
Show answer & solution

Answer: (A) The anchorage capacity of the bolt

A hydraulic jack pulls the bolt to check that the anchor holds its design load.

Question 26

Which tool is used to check the installation torque of mechanical roof bolts?

  1. Cap crimper
  2. Clinometer
  3. Torque wrench
  4. Abney level
Show answer & solution

Answer: (C) Torque wrench

Torque relates to bolt tension in mechanically anchored bolts.

Question 27

What are the written support rules that mine management sets for each working place called?

  1. Ventilation plan
  2. Mine plan
  3. Systematic support (timbering) rules
  4. Blasting register
Show answer & solution

Answer: (C) Systematic support (timbering) rules

Coal mine regulations require systematic support rules specifying spacing and type of supports.

Question 28

Which timber support consists of two legs and a horizontal cap?

  1. Lagging
  2. Three-piece timber set
  3. Timber chock (cog)
  4. Single prop
Show answer & solution

Answer: (B) Three-piece timber set

Three-piece sets (two legs and a collar) are common in roadways.

Question 29

What is a timber chock (cog)?

  1. A single vertical post
  2. A wedge used to tighten props
  3. A thin board between sets
  4. A crib of timber pieces stacked in alternate layers to support the roof
Show answer & solution

Answer: (D) A crib of timber pieces stacked in alternate layers to support the roof

Chocks provide high load capacity and stability at roadway junctions and goaf edges.

Question 30

What is lagging in underground support?

  1. Boards or mesh placed between sets to retain loose rock
  2. A rock bolt
  3. The main vertical post
  4. A cable anchor
Show answer & solution

Answer: (A) Boards or mesh placed between sets to retain loose rock

Lagging prevents loose rock from falling between support sets.

Question 31

What does NATM stand for in tunnelling and roadway support?

  1. New Austrian Tunnelling Method
  2. National Association of Tunnel Miners
  3. New American Tunnel Method
  4. Norwegian Advanced Tunnel Method
Show answer & solution

Answer: (A) New Austrian Tunnelling Method

NATM was developed by Rabcewicz, Müller and Pacher in the 1960s.

Question 32

What is the basic idea of NATM?

  1. Using very heavy rigid support
  2. Leaving the opening unsupported
  3. Using only tunnel boring machines
  4. Mobilising the strength of the surrounding rock with flexible early support and monitoring
Show answer & solution

Answer: (D) Mobilising the strength of the surrounding rock with flexible early support and monitoring

NATM uses shotcrete and bolts with convergence monitoring.

Question 33

Why should rock bolts be installed as soon as possible after excavation?

  1. To improve ventilation
  2. To prevent loosening and loss of rock mass strength
  3. Because they are cheaper when installed early
  4. To help blasting
Show answer & solution

Answer: (B) To prevent loosening and loss of rock mass strength

Delay allows loosening, which reduces the rock's self-supporting capacity.

Question 34

What is a coal bump?

  1. A sudden flood of the floor
  2. A roof bolting method
  3. Sudden violent failure of a highly stressed coal pillar or face
  4. A gas outburst only
Show answer & solution

Answer: (C) Sudden violent failure of a highly stressed coal pillar or face

Bumps occur in deep, strong coal and strong roof and floor conditions.

Question 35

What is destressing in rock burst-prone mines?

  1. Using timber supports
  2. Spraying water on the roof
  3. Increasing the extraction ratio
  4. Blasting or drilling to soften highly stressed rock ahead of the face
Show answer & solution

Answer: (D) Blasting or drilling to soften highly stressed rock ahead of the face

Destress blasting moves high stress deeper into the rock away from the face.

Question 36

What type of support is installed close to the face to protect workers before permanent support is placed?

  1. Barrier pillar
  2. Temporary support such as props or forepoling
  3. Hydraulic stowing
  4. Shaft pillar
Show answer & solution

Answer: (B) Temporary support such as props or forepoling

Temporary support covers the newly exposed roof at the face.

Question 37

What is the main cause of most roof fall accidents in underground coal mines?

  1. Working under unsupported or poorly supported roof
  2. Coal dust
  3. Water inflow
  4. Methane emission
Show answer & solution

Answer: (A) Working under unsupported or poorly supported roof

Most roof fall casualties occur at the face where support is missing or delayed.

Practice these 37 questions interactively →