Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Rock Mechanics & Ground Control: Pillar Design

Mining Engineering · Rock Mechanics & Ground Control

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does tributary area theory assume about the load on a pillar?

  1. Pillars carry no load
  2. Each pillar carries the full overburden weight of the area it supports
  3. Each pillar carries half the overburden
  4. Pillars carry only their own weight
Show answer & solution

Answer: (B) Each pillar carries the full overburden weight of the area it supports

Tributary area theory spreads the full overburden over pillar area; it is conservative for wide panels.

Question 2

What is the average stress on square pillars of width w with rooms of width b at vertical stress σv by tributary area theory?

  1. σv × w/(w + b)
  2. σv × (b/w)²
  3. σv × (w + b)/w
  4. σv × ((w + b)/w)²
Show answer & solution

Answer: (D) σv × ((w + b)/w)²

Each pillar supports a tributary area of (w + b)² on a pillar area of w².

Question 3

What is the extraction ratio in room and pillar mining?

  1. Ratio of seam height to width
  2. Proportion of the seam area that is mined out
  3. Ratio of pillar area to total area
  4. Ratio of coal sold to coal mined
Show answer & solution

Answer: (B) Proportion of the seam area that is mined out

Extraction ratio e = area extracted/total area.

Question 4

For square pillars, how is the extraction ratio e related to pillar width w and room width b?

  1. e = 1 − (w/(w + b))²
  2. e = b/w
  3. e = 1 − w/b
  4. e = (w/(w + b))²
Show answer & solution

Answer: (A) e = 1 − (w/(w + b))²

The pillar fraction is (w/(w + b))², so the mined fraction is one minus that.

Question 5

How does average pillar stress change as the extraction ratio increases?

  1. It decreases
  2. It becomes zero
  3. It increases, since σp = σv/(1 − e)
  4. It stays constant
Show answer & solution

Answer: (C) It increases, since σp = σv/(1 − e)

Higher extraction leaves less pillar area to carry the same load.

Question 6

How does increasing the width-to-height ratio of a pillar affect its strength?

  1. Strength becomes zero
  2. There is no effect
  3. Strength decreases
  4. Strength increases
Show answer & solution

Answer: (D) Strength increases

Wider, squatter pillars have more confined cores and higher strength.

Question 7

Which pillar strength formula developed for South African coal is σp = 7.2 h^−0.66 w^0.46 MPa?

  1. Bieniawski formula
  2. Holland formula
  3. Salamon–Munro formula
  4. Obert–Duvall formula
Show answer & solution

Answer: (C) Salamon–Munro formula

Salamon and Munro (1967) derived this power formula from failed and stable pillar cases.

Question 8

Which linear pillar strength formula is σp = σ1(0.64 + 0.36 w/h)?

  1. Salamon–Munro formula
  2. Bieniawski (Penn State) formula
  3. Holland formula
  4. Obert–Duvall formula
Show answer & solution

Answer: (B) Bieniawski (Penn State) formula

Bieniawski's formula is widely used in US coal pillar design.

Question 9

What are the constants a and b in the Obert–Duvall pillar strength formula σp = σ1(a + b w/h)?

  1. 0.5 and 0.5
  2. 0.64 and 0.36
  3. 0.778 and 0.222
  4. 1.0 and 0
Show answer & solution

Answer: (C) 0.778 and 0.222

Obert and Duvall (1967) proposed σp = σ1(0.778 + 0.222 w/h).

Question 10

What factor of safety is commonly used for long-term coal pillars in room and pillar design?

  1. 0.5
  2. 1.0
  3. 1.5 to 2.0
  4. 5.0
Show answer & solution

Answer: (C) 1.5 to 2.0

Main pillars are generally designed for a factor of safety of about 1.5–2.0.

Question 11

What happens in a cascading (domino) pillar failure?

  1. Failure of one pillar transfers load to its neighbours, causing rapid progressive collapse
  2. Only the roof bolts fail
  3. Pillars become stronger after failure
  4. One pillar fails alone without affecting others
Show answer & solution

Answer: (A) Failure of one pillar transfers load to its neighbours, causing rapid progressive collapse

Cascading failure can collapse a whole panel and cause air blasts.

Question 12

What is the large pillar left to protect main roadways or separate panels from mining-induced stress called?

  1. Crown pillar
  2. Stump
  3. Chain pillar
  4. Barrier pillar
Show answer & solution

Answer: (D) Barrier pillar

Barrier pillars isolate panels and limit load transfer and collapse spread.

Question 13

What is the pillar left around a shaft to protect it from subsidence damage called?

  1. Sill pillar
  2. Barrier pillar
  3. Rib pillar
  4. Shaft pillar
Show answer & solution

Answer: (D) Shaft pillar

Shaft pillars are sized using the angle of draw from the shaft and its surface structures.

Question 14

Which pillars separate adjacent longwall gate roads?

  1. Chain pillars
  2. Sill pillars
  3. Crown pillars
  4. Barrier pillars
Show answer & solution

Answer: (A) Chain pillars

Chain pillars between gate entries protect the tailgate during retreat.

Question 15

What is the horizontal pillar left at the base of a stope, above the level below, in metal mines?

  1. Rib pillar
  2. Sill pillar
  3. Barrier pillar
  4. Chain pillar
Show answer & solution

Answer: (B) Sill pillar

Sill pillars protect the haulage level beneath a stope.

Question 16

What is the pillar left between an open pit floor or the surface and underground stopes called?

  1. Rib pillar
  2. Crown pillar
  3. Chain pillar
  4. Sill pillar
Show answer & solution

Answer: (B) Crown pillar

A crown pillar prevents breakthrough of stopes to the surface or pit.

Question 17

What is the vertical pillar left between adjacent stopes along strike called?

  1. Rib pillar
  2. Barrier pillar
  3. Crown pillar
  4. Sill pillar
Show answer & solution

Answer: (A) Rib pillar

Rib pillars separate stopes and support the hanging wall.

Question 18

What is the final extraction of pillars in a room and pillar coal mine called?

  1. Stowing
  2. Development
  3. Benching
  4. Depillaring (retreat mining)
Show answer & solution

Answer: (D) Depillaring (retreat mining)

Pillars are extracted on retreat, letting the roof cave behind.

Question 19

What is a small remnant of pillar left during depillaring to support the roof temporarily called?

  1. Rib pillar
  2. Barrier pillar
  3. Stump (stook)
  4. Chain pillar
Show answer & solution

Answer: (C) Stump (stook)

Stumps provide short-term support while the working place is retreated.

Question 20

Why is hydraulic sand stowing done in some underground coal mines during depillaring?

  1. To support the roof and reduce surface subsidence
  2. To improve ventilation
  3. To assist blasting
  4. To drain the mine
Show answer & solution

Answer: (A) To support the roof and reduce surface subsidence

Sand fill replaces extracted coal and limits roof caving and subsidence.

Question 21

Why is the in-situ strength of a coal pillar lower than the strength of small laboratory samples?

  1. Pillars are made of a different material
  2. Larger volumes contain more cleats and flaws
  3. Pillars have no confinement at all
  4. Laboratory samples are always wet
Show answer & solution

Answer: (B) Larger volumes contain more cleats and flaws

This size effect is why coal pillar formulas use a reduced in-situ strength.

Question 22

Beyond about what cube size does coal strength stop decreasing with size, according to Bieniawski?

  1. About 1.5 m
  2. About 10 mm
  3. About 15 m
  4. About 150 m
Show answer & solution

Answer: (A) About 1.5 m

Bieniawski found a critical size of about 1.5 m (≈ 5 ft) for coal cubes.

Question 23

Why does tributary area theory overestimate pillar loads in narrow panels?

  1. It treats rock as weightless
  2. It ignores the overburden weight
  3. It ignores depth
  4. Part of the load arches onto barrier pillars and solid abutments
Show answer & solution

Answer: (D) Part of the load arches onto barrier pillars and solid abutments

In narrow panels, abutments carry part of the overburden load.

Question 24

What does ARMPS stand for in coal pillar design?

  1. Automatic Roof and Mine Pillar Support
  2. Advanced Rock Mass Pillar System
  3. Analysis of Retreat Mining Pillar Stability
  4. Applied Rock Mechanics Pillar Standard
Show answer & solution

Answer: (C) Analysis of Retreat Mining Pillar Stability

ARMPS is a NIOSH method for retreat room and pillar design.

Question 25

What is the main danger of slender pillars with a very low width-to-height ratio?

  1. They have no danger
  2. Sudden brittle failure
  3. They cause only floor heave
  4. They become too strong
Show answer & solution

Answer: (B) Sudden brittle failure

Slender pillars lack a confined core and can fail violently.

Question 26

Why is depth of cover important in pillar design?

  1. Depth reduces pillar load
  2. It only affects ventilation
  3. Depth has no effect
  4. Vertical stress, and therefore pillar load, increases with depth
Show answer & solution

Answer: (D) Vertical stress, and therefore pillar load, increases with depth

σv ≈ 0.025–0.027 MPa per metre, so deeper seams need larger pillars.

Question 27

Why does the core of a wide pillar stay strong while the edges yield?

  1. The edges are wetter
  2. The core is confined by the surrounding rock
  3. The core contains different coal
  4. The core creeps more
Show answer & solution

Answer: (B) The core is confined by the surrounding rock

Confinement increases from the free face towards the centre of a pillar.

Question 28

What is a yield pillar?

  1. A crown pillar
  2. A shaft pillar
  3. A small pillar designed to yield and transfer load to larger pillars or abutments
  4. A large barrier pillar
Show answer & solution

Answer: (C) A small pillar designed to yield and transfer load to larger pillars or abutments

Yield pillars are used in deep longwall gate roads to reduce bump risk.

Question 29

What is the effect of a weak fireclay floor beneath coal pillars?

  1. Pillars punch into the floor and cause floor heave
  2. It has no effect
  3. It prevents subsidence
  4. It increases pillar strength
Show answer & solution

Answer: (A) Pillars punch into the floor and cause floor heave

Weak floors fail in bearing under pillar load.

Question 30

Which coal mining method relies mainly on pillars for permanent roof support?

  1. Block caving
  2. Sublevel caving
  3. Longwall
  4. Bord and pillar (room and pillar)
Show answer & solution

Answer: (D) Bord and pillar (room and pillar)

Room and pillar leaves a regular grid of pillars to carry the overburden.

Question 31

What does the term "bord" mean in bord and pillar mining?

  1. A roadway driven in the seam
  2. A pillar of coal
  3. A vertical shaft
  4. The caved goaf
Show answer & solution

Answer: (A) A roadway driven in the seam

Bords are roadways; cross-cuts called splits or walls connect them around pillars.

Question 32

What is the extraction ratio for square pillars 20 m wide separated by rooms 5 m wide?

  1. 20%
  2. 36%
  3. 50%
  4. 64%
Show answer & solution

Answer: (B) 36%

e = 1 − (20/25)² = 1 − 0.64 = 0.36.

Question 33

If the vertical stress is 5 MPa and the extraction ratio is 50%, what is the average pillar stress by tributary area theory?

  1. 2.5 MPa
  2. 5 MPa
  3. 10 MPa
  4. 20 MPa
Show answer & solution

Answer: (C) 10 MPa

σp = σv/(1 − e) = 5/0.5 = 10 MPa.

Question 34

What is the safety factor of a pillar with a strength of 12 MPa carrying an average stress of 8 MPa?

  1. 0.67
  2. 1.0
  3. 1.5
  4. 2.0
Show answer & solution

Answer: (C) 1.5

FS = strength/stress = 12/8 = 1.5.

Question 35

What do barrier pillars between coal panels mainly prevent?

  1. Surface noise
  2. Coal dust explosions only
  3. Air leakage only
  4. Pillar collapse spreading from one panel to the next
Show answer & solution

Answer: (D) Pillar collapse spreading from one panel to the next

Barrier pillars confine any panel collapse and limit load transfer.

Question 36

Which mining method is most commonly used in the underground coal mines of Balochistan, such as Duki and Sor Range?

  1. Longwall with powered supports
  2. Block caving
  3. Open pit mining
  4. Room and pillar (bord and pillar)
Show answer & solution

Answer: (D) Room and pillar (bord and pillar)

Most Balochistan coal mines are small, steeply dipping seams worked by room and pillar methods with timber support.

Practice these 36 questions interactively →