Who developed the Rock Quality Designation (RQD)?
Show answer & solution
Answer: (C) Deere
D.U. Deere introduced RQD in 1964.
Mining Engineering · Rock Mechanics & Ground Control
37 questions, each with the answer and a worked solution.
Practice interactively and track your score →Who developed the Rock Quality Designation (RQD)?
Answer: (C) Deere
D.U. Deere introduced RQD in 1964.
How is RQD calculated from a drill core run?
Answer: (A) Sum of lengths of core pieces 100 mm or longer divided by the run length, × 100
RQD counts only sound pieces of at least 100 mm; total recovery is a different measure.
Which minimum core size is recommended for RQD measurement?
Answer: (D) NX size (about 54 mm)
Deere recommended at least NX core (about 54.7 mm diameter) drilled with double-tube barrels.
What rock quality is indicated by an RQD of 90 to 100%?
Answer: (B) Excellent
RQD classes: 0–25 very poor, 25–50 poor, 50–75 fair, 75–90 good, 90–100 excellent.
What rock quality is indicated by an RQD of 25 to 50%?
Answer: (D) Poor
An RQD between 25 and 50% is classed as poor.
What is Palmström's relation for estimating RQD from the volumetric joint count Jv?
Answer: (C) RQD = 115 − 3.3 Jv
Palmström (1982): RQD = 115 − 3.3 Jv, where Jv is joints per cubic metre.
Who developed the Rock Mass Rating (RMR) system?
Answer: (A) Bieniawski
Z.T. Bieniawski developed the RMR (Geomechanics) classification in 1973 at CSIR, South Africa.
How many parameters, including the orientation adjustment, are used in Bieniawski's RMR system?
Answer: (B) Six
Five rated parameters (UCS, RQD, spacing, joint condition, groundwater) plus an adjustment for joint orientation.
Which parameter is not used in the RMR system?
Answer: (B) Stress reduction factor
The stress reduction factor (SRF) belongs to Barton's Q-system.
What is the maximum basic RMR value?
Answer: (C) 100
The five rated parameters add up to a maximum of 100.
Which RMR class describes rock with a rating of 81 to 100?
Answer: (A) Class I, very good rock
RMR 81–100 is Class I (very good rock).
Which RMR class corresponds to fair rock with a rating of 41 to 60?
Answer: (D) Class III
RMR 41–60 is Class III (fair rock).
Which parameter carries the highest maximum rating of 30 points in RMR89?
Answer: (B) Condition of discontinuities
RMR89 maxima: UCS 15, RQD 20, spacing 20, joint condition 30, groundwater 15.
What maximum rating does the uniaxial compressive strength of intact rock carry in RMR89?
Answer: (B) 15
Intact rock strength carries up to 15 points in RMR89.
Who developed the Q-system of rock mass classification?
Answer: (A) Barton, Lien and Lunde
The Q-system was developed at the Norwegian Geotechnical Institute in 1974.
What is the formula for the rock mass quality Q in the Q-system?
Answer: (C) Q = (RQD/Jn) × (Jr/Ja) × (Jw/SRF)
The three quotients represent block size, inter-block shear strength and active stress.
What does the quotient RQD/Jn represent in the Q-system?
Answer: (D) Relative block size
RQD divided by the joint set number gives a measure of block size.
What does the quotient Jr/Ja represent in the Q-system?
Answer: (A) Inter-block shear strength
Joint roughness divided by joint alteration reflects the shear strength between blocks.
What does the quotient Jw/SRF represent in the Q-system?
Answer: (D) Active stress
Water reduction factor divided by the stress reduction factor is an empirical active-stress term.
What is the range of Q values in the Q-system?
Answer: (C) 0.001 to 1000
Q runs on a logarithmic scale from exceptionally poor (0.001) to exceptionally good (1000).
What does SRF stand for in the Q-system?
Answer: (C) Stress Reduction Factor
SRF accounts for loosening, rock stress in competent rock and squeezing or swelling.
What is Bieniawski's correlation between RMR and Q?
Answer: (D) RMR = 9 ln Q + 44
Bieniawski (1976) proposed RMR = 9 ln Q + 44.
What does ESR stand for in Q-system support design?
Answer: (A) Excavation Support Ratio
ESR reflects the required safety level depending on the use of the excavation.
How is the equivalent dimension De defined in the Q-system?
Answer: (B) Span or height of the excavation divided by ESR
De = span (or height)/ESR is plotted against Q to choose support.
Which ESR value is generally used for permanent mine openings such as main haulages and shafts?
Answer: (B) 1.6
Barton suggests ESR 3–5 for temporary mine openings and about 1.6 for permanent mine openings.
Who introduced the Geological Strength Index (GSI)?
Answer: (D) Hoek
E. Hoek introduced GSI in the 1990s for use with the Hoek–Brown criterion.
On which two observations is GSI estimated from the standard chart?
Answer: (C) Rock mass structure (blockiness) and surface condition of discontinuities
The GSI chart combines blockiness with joint surface quality.
Which rock mass classification system is a modification of RMR developed for caving mines?
Answer: (A) Laubscher's Mining Rock Mass Rating (MRMR)
Laubscher adjusted RMR for weathering, mining stresses, joint orientation and blasting.
Which classification system modifies RMR specifically for rock slopes?
Answer: (C) Slope Mass Rating (SMR) by Romana
Romana's SMR adds factors for joint–slope orientation and excavation method.
Which early classification for estimating loads on steel tunnel supports was proposed by Terzaghi in 1946?
Answer: (D) Rock load classification
Terzaghi's rock load classification estimated loads on steel sets from rock description.
Who proposed the Rock Structure Rating (RSR) system?
Answer: (A) Wickham, Tiedemann and Skinner
RSR (1972) was the first rating system to estimate support for tunnels quantitatively.
What does stand-up time mean in rock mass classification?
Answer: (B) Time an unsupported span can stand without failure
Stand-up time decreases rapidly as span increases and rock quality falls.
Who first related stand-up time to the active unsupported span?
Answer: (B) Lauffer
Lauffer (1958) proposed the stand-up time concept later used in RMR.
What is the approximate relation between GSI and RMR89 when RMR89 is greater than 23, using a dry groundwater rating and no orientation adjustment?
Answer: (D) GSI = RMR89 − 5
Hoek recommended GSI = RMR89′ − 5 with groundwater rated 15 and no orientation adjustment.
In joint surveys, what is the azimuth of the horizontal projection of the line of steepest dip called?
Answer: (C) Dip direction
Dip direction is measured clockwise from north and is at 90° to strike.
Which simple device is used to record joint surface roughness profiles for estimating JRC?
Answer: (A) Barton comb (profile gauge)
The profile is compared with Barton's standard roughness profiles.
What is the range of Joint Roughness Coefficient (JRC) values?
Answer: (C) 0 to 20
JRC ranges from 0 (smooth, flat) to 20 (very rough).