How does the Mohr–Coulomb criterion express the shear strength of rock?
Show answer & solution
Answer: (D) τ = c + σn tan φ
Shear strength equals cohesion plus normal stress times the tangent of the friction angle.
Mining Engineering · Rock Mechanics & Ground Control
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →How does the Mohr–Coulomb criterion express the shear strength of rock?
Answer: (D) τ = c + σn tan φ
Shear strength equals cohesion plus normal stress times the tangent of the friction angle.
What does φ represent in the Mohr–Coulomb criterion?
Answer: (A) Angle of internal friction
φ is the angle of internal friction and c is cohesion.
According to Mohr–Coulomb theory, at what angle to the major principal stress does the shear failure plane form?
Answer: (B) 45° − φ/2
The failure plane is inclined at 45° − φ/2 to σ1 (its normal is at 45° + φ/2).
What is the relation between uniaxial compressive strength, cohesion c and friction angle φ in the Mohr–Coulomb criterion?
Answer: (D) UCS = 2c cos φ/(1 − sin φ)
With σ3 = 0 the criterion gives σc = 2c cos φ/(1 − sin φ).
Which non-linear empirical failure criterion for rock uses the parameters mb, s and a?
Answer: (B) Hoek–Brown criterion
Generalised Hoek–Brown: σ1 = σ3 + σci(mb σ3/σci + s)^a.
What is the value of the Hoek–Brown parameter s for intact rock?
Answer: (C) 1
s = 1 for intact rock and decreases towards 0 for heavily jointed rock.
On what does the Hoek–Brown constant mi mainly depend?
Answer: (A) Rock type (mineralogy and texture)
mi ranges from about 4 for claystone to about 32 for granite, depending on rock type.
Which parameter in the generalised Hoek–Brown criterion accounts for blast damage and stress relaxation?
Answer: (B) Disturbance factor D
D varies from 0 for undisturbed rock to 1 for very disturbed rock such as production-blasted pit slopes.
What is the range of the Hoek–Brown disturbance factor D?
Answer: (B) 0 to 1
D = 0 means undisturbed rock; D = 1 means heavily disturbed rock.
Which failure theory assumes that fracture begins from tensile stress concentrations at the tips of microcracks?
Answer: (D) Griffith theory
Griffith (1920) explained brittle fracture by crack-tip tensile stresses.
According to the original Griffith theory, what is the ratio of uniaxial compressive strength to tensile strength?
Answer: (C) 8
The two-dimensional Griffith criterion predicts σc = 8σt.
What is the maximum tangential stress at the boundary of a circular opening in a hydrostatic stress field p?
Answer: (A) 2p
In a hydrostatic field the tangential stress is uniform at 2p around a circular opening.
What is the maximum stress concentration factor at the sidewall of a circular opening under uniaxial vertical stress?
Answer: (C) 3
Kirsch's solution gives 3p at the sidewalls and −p (tension) at the roof and floor.
What stress develops at the roof and floor of a circular opening in a uniaxial vertical stress field p?
Answer: (D) Tensile stress equal to p
Kirsch's solution gives a tangential stress of −p at the crown and invert.
Which classical solution gives the elastic stresses around a circular hole in an infinite plate?
Answer: (A) Kirsch solution
Kirsch (1898) derived stresses around a circular hole under biaxial loading.
At about what distance from a circular opening does the stress disturbance become small?
Answer: (C) About three radii from the centre
Beyond about three radii the stresses are close to the original field stresses.
Which shape of opening gives the lowest stress concentration when horizontal stress is greater than vertical stress?
Answer: (B) An ellipse with its long axis horizontal
The best shape has its long axis parallel to the major principal stress.
Where do the highest stress concentrations occur around a rectangular opening?
Answer: (A) At the corners
Sharp corners concentrate stress; rounding the corners reduces it.
What is the zone of yielded and broken rock immediately around an underground opening called?
Answer: (D) Plastic (yielded) zone
Where stress exceeds strength, a plastic or fractured zone forms around the opening.
What is the area of increased stress beside an excavation, such as alongside a longwall panel, called?
Answer: (B) Abutment zone
Load removed from the excavated area is transferred to the abutments.
Which shear strength criterion for rock joints uses JRC and JCS?
Answer: (D) Barton–Bandis criterion
Barton: τ = σn tan[JRC log10(JCS/σn) + φr].
In Patton's bilinear model for rough joints, what is the effective friction angle at low normal stress?
Answer: (A) Basic friction angle plus asperity angle (φb + i)
At low normal stress, sliding rides over asperities, adding the angle i to φb.
What is the friction angle of a joint after large shear displacement called?
Answer: (C) Residual friction angle
After asperities are sheared off, strength falls to the residual value.
Which principle states that effective stress equals total stress minus pore water pressure?
Answer: (D) Terzaghi's effective stress principle
σ′ = σ − u; shear strength depends on effective stress.
How does water pressure in a joint affect its shear strength?
Answer: (A) It reduces effective normal stress and therefore shear strength
Pore pressure lowers effective normal stress, which lowers frictional resistance.
What is the shape of the Mohr–Coulomb failure envelope in shear–normal stress space?
Answer: (C) A straight line
The Mohr–Coulomb envelope is linear with slope tan φ and intercept c.
In a Mohr circle diagram, what does the radius of the circle represent?
Answer: (B) (σ1 − σ3)/2, the maximum shear stress
The centre is at (σ1 + σ3)/2 and the radius equals the maximum shear stress.
Which apparatus holds a rock core under confining pressure during a triaxial test?
Answer: (D) Hoek cell
The Hoek triaxial cell applies hydraulic confining pressure through a rubber sleeve.
How does increasing confining pressure generally affect rock behaviour in triaxial tests?
Answer: (B) Strength increases and behaviour becomes more ductile
Confinement suppresses crack growth, raising strength and causing a brittle–ductile transition.
How does the deformation modulus of a jointed rock mass usually compare with the modulus of intact rock?
Answer: (C) It is lower because joints add deformability
Joints close and slip under load, so the rock mass is more deformable than intact rock.
Which in-situ test measures rock mass deformability by loading a rigid plate on a prepared rock surface?
Answer: (A) Plate load (plate bearing) test
The plate load test gives the in-situ deformation modulus of the rock mass.
Which numerical method is best suited to model a blocky, jointed rock mass as separate blocks?
Answer: (C) Distinct element method (e.g., UDEC)
The distinct element method allows blocks to move, rotate and separate along joints.
What does a factor of safety less than 1 for a rock structure indicate?
Answer: (A) Driving forces exceed resisting forces and failure is expected
FS = resisting forces/driving forces; FS < 1 indicates instability.
What does the convergence–confinement method relate in tunnel and roadway support design?
Answer: (D) The ground reaction curve and the support reaction curve
Support pressure is found where the support characteristic meets the ground reaction curve.
What is the slow, large inward deformation of weak rock around an opening under high stress called?
Answer: (B) Squeezing ground
Squeezing occurs in weak, highly stressed rocks such as shales and fault gouge.
Which brittle failure mode involves thin slabs breaking off the wall of a highly stressed opening in hard rock?
Answer: (B) Spalling
Spalling (slabbing) occurs in massive hard rock when tangential stress approaches a fraction of the UCS.