What is the Reynolds number?
Show answer & solution
Answer: (A) The ratio of inertia force to viscous force
Re = ρVD/μ = VD/ν.
Mechanical Engineering · Hydraulics & Fluid Mechanics
41 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the Reynolds number?
Answer: (A) The ratio of inertia force to viscous force
Re = ρVD/μ = VD/ν.
Below what Reynolds number is pipe flow usually laminar?
Answer: (B) 2000
Flow between about 2000 and 4000 is transitional.
Above what Reynolds number is pipe flow usually turbulent?
Answer: (D) 4000
A large Reynolds number indicates highly turbulent flow.
What is the velocity profile of laminar flow in a circular pipe?
Answer: (C) Parabolic
It is described by the Hagen–Poiseuille equation.
In laminar flow through a pipe, how is maximum velocity related to mean velocity?
Answer: (D) Maximum velocity = 2 × mean velocity
The maximum occurs at the pipe centre.
What is the shear stress at the centre line of a pipe flowing full?
Answer: (A) Zero
Shear stress varies linearly from zero at the centre to maximum at the wall.
What is the Darcy friction factor for laminar flow in a pipe?
Answer: (D) 64/Re
It does not depend on pipe roughness in laminar flow.
What is the Darcy–Weisbach equation for head loss due to friction?
Answer: (B) hf = fLV²/(2gD)
f is the Darcy friction factor.
Which chart gives the friction factor as a function of Reynolds number and relative roughness?
Answer: (C) Moody diagram
It covers laminar, transitional and turbulent flow.
What is the head loss due to sudden enlargement of a pipe?
Answer: (A) (V₁ − V₂)²/2g
V₁ and V₂ are the velocities before and after the enlargement.
What is the head loss at the entrance to a pipe from a reservoir, usually taken as?
Answer: (B) 0.5V²/2g
V is the velocity in the pipe.
What is the head loss at the exit of a pipe into a reservoir?
Answer: (C) V²/2g
All the kinetic energy of the flow is lost.
What is the hydraulic gradient line (HGL)?
Answer: (A) A line joining the pressure-plus-datum heads along a pipe
The energy gradient line lies above it by V²/2g.
When are two pipe systems considered equivalent?
Answer: (C) When they carry the same discharge with the same head loss
An equivalent pipe can replace a compound pipe.
For pipes in series, what is the total head loss?
Answer: (D) The sum of the head losses in each pipe
The same discharge flows through each pipe.
For pipes in parallel, what is common to all branches?
Answer: (B) The head loss
The total discharge is the sum of the branch discharges.
For maximum power transmission through a pipe, what should be the head lost to friction?
Answer: (B) One-third of the total head supplied
Maximum efficiency at this condition is 66.7%.
What is water hammer?
Answer: (C) A sudden rise in pressure in a pipe when flow is suddenly stopped, such as by quick valve closure
Surge tanks and slow valve closure reduce water hammer.
What is the purpose of a surge tank in a hydroelectric scheme?
Answer: (D) To absorb pressure rises and supply water during sudden load changes, protecting the penstock from water hammer
It is placed between the tunnel and the penstock.
What is a boundary layer?
Answer: (A) The thin layer of fluid near a solid surface in which velocity changes from zero to the free-stream value
It was introduced by Ludwig Prandtl in 1904.
What causes boundary layer separation?
Answer: (B) An adverse pressure gradient (pressure increasing in the flow direction)
Separation creates a wake and increases drag.
What is the wake behind a body?
Answer: (D) The region of disturbed, low-pressure flow behind a body after separation
Streamlining reduces the size of the wake.
What is drag?
Answer: (C) The force component on a body parallel to the direction of relative flow
Lift acts perpendicular to the flow direction.
What does Stokes' law give?
Answer: (A) The drag force on a small sphere moving slowly through a viscous fluid (F = 3πμDV)
It applies at very low Reynolds numbers.
What is the Froude number?
Answer: (A) The ratio of inertia force to gravity force
It governs flows with a free surface, such as ship models and spillways.
What is the Mach number?
Answer: (D) The ratio of inertia force to elastic force (flow velocity to speed of sound)
It is important in high-speed compressible flows.
What is the Weber number?
Answer: (C) The ratio of inertia force to surface tension force
It is important in droplet and capillary flows.
What is the Euler number?
Answer: (B) The ratio of pressure force to inertia force
It is used in problems dominated by pressure changes.
Which dimensionless number is most important for model testing of ships?
Answer: (D) Froude number
Wave-making resistance depends on gravity.
Which dimensionless number is most important for flow through closed pipes?
Answer: (B) Reynolds number
Viscous forces dominate in closed conduits.
For what Mach number range is flow called supersonic?
Answer: (A) Greater than 1
Hypersonic flow usually means Mach number greater than about 5.
How does the speed of sound in an ideal gas depend on temperature?
Answer: (C) It is proportional to the square root of absolute temperature
c = √(γRT).
What is the Buckingham π theorem used for?
Answer: (B) Forming dimensionless groups in dimensional analysis
With n variables and m fundamental dimensions, there are n − m π groups.
What is the main purpose of the principle of similitude?
Answer: (C) Designing models whose test results can be applied to full-size prototypes
Geometric, kinematic and dynamic similarity are required.
A 100 m ship is to travel at 10 m/s. At what speed should a 1:25 scale model be towed for Froude similarity?
Answer: (A) 2 m/s
Velocity scales as √(length ratio): 10/√25 = 2 m/s.
A reservoir model at 1:225 scale empties in 4 minutes. How long would the prototype take under Froude similarity?
Answer: (B) 60 minutes
Time scales as √(length ratio): 4 × √225 = 60 minutes.
What does the Navier–Stokes equation include?
Answer: (D) Pressure, gravity and viscous forces
It is the general equation of motion for viscous fluids.
What is normal depth in open channel flow?
Answer: (A) The depth of flow corresponding to uniform flow
It depends on discharge, slope, roughness and channel shape.
What is cavitation?
Answer: (D) Formation and collapse of vapour bubbles when local pressure falls to the vapour pressure of the liquid
Collapsing bubbles cause noise, vibration and pitting of metal surfaces.
What happens to friction factor in fully rough turbulent flow?
Answer: (B) It depends only on relative roughness, not on Reynolds number
This region is shown on the right side of the Moody diagram.
What is the laminar sub-layer?
Answer: (A) A very thin layer next to the wall within a turbulent boundary layer where flow remains laminar
Pipes are hydraulically smooth when roughness lies within this layer.