What does Pascal's law state?
Show answer & solution
Answer: (A) The pressure at a point in a fluid at rest is the same in all directions
It is the principle behind hydraulic presses, jacks and brakes.
Mechanical Engineering · Hydraulics & Fluid Mechanics
35 questions, each with the answer and a worked solution.
Practice interactively and track your score →What does Pascal's law state?
Answer: (A) The pressure at a point in a fluid at rest is the same in all directions
It is the principle behind hydraulic presses, jacks and brakes.
What is hydrostatic pressure at a depth h in a liquid of specific weight w?
Answer: (B) wh
p = ρgh, measured above the surface pressure.
Why is the normal stress at a point in a fluid the same in all directions?
Answer: (B) When there is no relative motion between fluid layers, no shear stress exists
This holds for fluids at rest or moving as a rigid body.
What is a pressure head of 25 m of water equal to, approximately?
Answer: (C) 245 kN/m²
p = 9.81 × 25 ≈ 245 kN/m².
What is the height of a water column equivalent to 3.75 cm of mercury?
Answer: (C) 51 cm
3.75 × 13.6 = 51 cm of water.
The air above oil (sp. gr. 0.8) in a tank is at 0.1 kg/cm² gauge. What is the pressure 2.5 m below the oil surface?
Answer: (C) 3 m of water column
0.1 kg/cm² = 1 m of water, and 2.5 × 0.8 = 2 m, so the total is 3 m.
What is the height of water in a barometer equivalent to standard atmospheric pressure?
Answer: (C) About 10.3 m
760 mm × 13.6 ≈ 10.3 m.
Why is mercury preferred in barometers?
Answer: (A) Its high density gives a short column and its vapour pressure is negligible
A water barometer would need a tube over 10 m long.
Which instrument measures atmospheric pressure?
Answer: (D) Barometer
A Fortin barometer uses mercury.
What is a manometer used to measure?
Answer: (A) Pressure in pipes and vessels using a liquid column
Simple manometers include piezometers and U-tube manometers.
What does a differential manometer measure?
Answer: (B) The difference in pressure between two points
It is often used across venturimeters and orifice meters.
Why is one leg of a manometer inclined?
Answer: (D) To increase sensitivity by giving a longer reading for a small pressure change
An inclined manometer is used for small pressure differences.
Why is alcohol sometimes used in manometers for small pressure differences?
Answer: (B) Its low density gives a longer column for a given pressure difference
A longer column gives a more accurate reading.
Which pressure gauge uses a curved, elastic metal tube that straightens under pressure?
Answer: (A) Bourdon tube gauge
It is the most common mechanical pressure gauge.
On which principle does the McLeod vacuum gauge work?
Answer: (D) Boyle's law
It compresses a known volume of low-pressure gas.
Which gauge is used for measuring very high vacuum (extremely low pressures)?
Answer: (D) Ionisation gauge
Pirani and McLeod gauges cover moderately low pressures.
On which principle does a dead-weight pressure gauge tester work?
Answer: (B) Pascal's law
Known weights on a piston generate known pressures for calibration.
What is the total pressure (hydrostatic force) on a plane surface submerged in a liquid?
Answer: (A) Specific weight × area × depth of the centroid
F = w A x̄ for vertical, horizontal or inclined surfaces.
What is the centre of pressure?
Answer: (C) The point on a submerged surface through which the resultant hydrostatic force acts
It lies below the centroid for vertical and inclined surfaces.
Where does the centre of pressure of a vertical submerged plane surface lie compared with its centroid?
Answer: (A) Below the centroid
Pressure increases with depth, shifting the resultant downward.
What is the depth of the centre of pressure of a vertical rectangular gate 6 m high, when the water surface is at its top edge?
Answer: (C) 4 m
For a rectangle with its top at the surface, h_cp = 2/3 × height.
A 3 m × 3 m vertical square plate has its upper edge at the water surface. What is the hydrostatic force on it?
Answer: (B) 13,500 kgf
F = 1000 × 9 m² × 1.5 m = 13,500 kgf.
What is the horizontal component of hydrostatic force on a curved surface equal to?
Answer: (D) The force on the vertical projection of the curved surface
It acts through the centre of pressure of the projection.
What is the vertical component of hydrostatic force on a curved surface equal to?
Answer: (B) The weight of liquid supported vertically above the curved surface
It acts through the centre of gravity of that liquid volume.
In a hydraulic press with a 15 cm ram and a 1.5 cm plunger, what force on the plunger lifts 1 tonne?
Answer: (B) 10 kg
Force ratio = (1.5/15)² = 1/100.
How does pressure vary with depth in a static liquid of constant density?
Answer: (D) It increases linearly with depth
dp/dz = −ρg.
How does atmospheric pressure change with increasing altitude?
Answer: (A) It decreases, quickly at first and then more gradually
Air density also falls with altitude.
What happens to the free surface of a liquid in a tank accelerating horizontally?
Answer: (D) It becomes inclined, rising at the rear
tan θ = a/g.
What shape does the free surface of a liquid take in a cylinder rotating about its vertical axis?
Answer: (C) A paraboloid
This is a forced vortex.
What is the increase in pressure at the outer edge of a liquid-filled drum of radius R rotating at ω rad/s?
Answer: (A) ρω²R²/2
Pressure increases with the square of the radius.
What is gauge pressure?
Answer: (A) Pressure measured relative to local atmospheric pressure
Absolute pressure = gauge pressure + atmospheric pressure.
What is a piezometer tube suitable for?
Answer: (C) Measuring moderate gauge pressures of liquids
It cannot measure gas pressures or large pressures conveniently.
What is the standard atmospheric pressure at sea level?
Answer: (C) 101.325 kN/m²
It equals 760 mm of mercury.
What is the pressure at the bottom of a 10 m deep column of water, in gauge terms?
Answer: (C) About 98.1 kN/m²
p = ρgh = 1000 × 9.81 × 10.
Which device uses Pascal's law to multiply force for lifting vehicles?
Answer: (B) Hydraulic jack
A small force on a small piston creates a large force on a large piston.