What is the Barkhausen criterion for sustained oscillation?
Show answer & solution
Answer: (B) Loop gain equal to one with total phase shift of 0° or 360°
Practical oscillators start with loop gain slightly above one.
Electrical Engineering · Electronics
29 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the Barkhausen criterion for sustained oscillation?
Answer: (B) Loop gain equal to one with total phase shift of 0° or 360°
Practical oscillators start with loop gain slightly above one.
How many RC sections are commonly used in an RC phase shift oscillator to provide 180° phase shift?
Answer: (D) Three
The amplifier provides the other 180°.
What is the frequency of oscillation of a three-section RC phase shift oscillator with equal R and C?
Answer: (B) 1/(2πRC√6)
The amplifier gain must be at least 29.
What is the frequency of oscillation of a Wien bridge oscillator with equal R and C values?
Answer: (C) 1/(2πRC)
It is widely used for audio frequency oscillators.
What minimum amplifier gain does a Wien bridge oscillator require?
Answer: (B) 3
The Wien network attenuates by one-third at the oscillation frequency.
What feedback network distinguishes a Colpitts oscillator?
Answer: (A) A tank circuit with a capacitive voltage divider (split capacitors)
Colpitts oscillators are used at radio frequencies.
What feedback network distinguishes a Hartley oscillator?
Answer: (C) A tank circuit with a tapped inductor or two inductors
The capacitor sets frequency with the total inductance.
Why are crystal oscillators very stable in frequency?
Answer: (D) The quartz crystal has a very high Q and stable resonance due to the piezoelectric effect
They are used in clocks, computers and communication systems.
Which effect allows a quartz crystal to act as a resonator?
Answer: (A) Piezoelectric effect
Mechanical vibration and electric voltage are coupled.
What is an astable multivibrator?
Answer: (B) A circuit with no stable state that continuously switches and generates a square wave
It is a free-running oscillator.
What is a monostable multivibrator?
Answer: (A) A circuit with one stable state that produces a single pulse of fixed width when triggered
It is also called a one-shot.
What is a bistable multivibrator?
Answer: (D) A circuit with two stable states that changes state only when triggered
A flip-flop is a bistable multivibrator.
What is the output frequency of a 555 timer in astable mode with RA, RB and C?
Answer: (C) f = 1.44/((RA + 2RB)C)
The duty cycle is set by RA and RB.
What is the approximate astable frequency of a 555 timer with RA = 1 kΩ, RB = 10 kΩ and C = 0.1 µF?
Answer: (D) About 686 Hz
f = 1.44/(21,000 × 0.1 × 10⁻⁶) ≈ 686 Hz.
What is the pulse width of a 555 timer in monostable mode with resistor R and capacitor C?
Answer: (B) 1.1RC
It is independent of supply voltage.
What is a voltage-controlled oscillator (VCO)?
Answer: (C) An oscillator whose output frequency varies with a control voltage
VCOs are key parts of phase-locked loops.
What is a phase-locked loop (PLL)?
Answer: (A) A feedback system that locks the phase and frequency of an oscillator to a reference signal
PLLs are used in frequency synthesis and demodulation.
Which type of oscillator is generally used to generate radio frequencies?
Answer: (C) LC oscillators such as Colpitts and Hartley
LC circuits are practical at high frequencies.
Which oscillator is commonly used for low audio frequencies with good waveform purity?
Answer: (A) Wien bridge oscillator
RC oscillators suit low frequencies.
What is a relaxation oscillator?
Answer: (B) An oscillator that produces non-sinusoidal waveforms by charging and discharging a capacitor
UJT and 555 circuits are examples.
What is the effect of losses in the tank circuit of an LC oscillator?
Answer: (D) They reduce Q, so the amplifier must supply energy to sustain oscillation
The active device makes up for energy dissipated each cycle.
What is the frequency of an LC tank circuit with L = 10 µH and C = 100 pF?
Answer: (B) About 5.03 MHz
f = 1/(2π√(10⁻⁵ × 10⁻¹⁰)) ≈ 5.03 MHz.
Why do practical oscillators start with loop gain slightly greater than one?
Answer: (C) So that oscillations build up from noise and then stabilise as gain limits
Amplitude control keeps gain at one in steady state.
What is the duty cycle of a 555 astable with RA = RB?
Answer: (C) About 66.7%
Duty = (RA + RB)/(RA + 2RB) = 2/3.
What is the main use of a crystal oscillator in a microcontroller system?
Answer: (A) To provide an accurate, stable clock frequency
Typical crystals are in the MHz range.
Which component sets the timing in a 555 timer circuit?
Answer: (D) External resistors and a capacitor
Timing is set by RC charging between thresholds.
What are the threshold levels of the internal comparators of a 555 timer?
Answer: (D) One-third and two-thirds of the supply voltage
The capacitor charges and discharges between these levels.
What type of output waveform does a Wien bridge oscillator produce?
Answer: (B) A low-distortion sine wave
Amplitude stabilisation keeps distortion low.
What is a sawtooth (ramp) generator commonly used for?
Answer: (A) Time-base sweeps and PWM generation
A capacitor charged by a constant current gives a linear ramp.