Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Electronics: Amplifiers and Feedback

Electrical Engineering · Electronics

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the conduction angle of a class A amplifier?

  1. Less than 180°
  2. 360°
  3. Between 180° and 360° only
  4. 180°
Show answer & solution

Answer: (B) 360°

The transistor conducts throughout the input cycle.

Question 2

What is the maximum theoretical efficiency of a transformer-coupled class A amplifier?

  1. 25%
  2. 50%
  3. 78.5%
  4. 100%
Show answer & solution

Answer: (B) 50%

With a resistive load it is only 25%.

Question 3

What is the maximum theoretical efficiency of a class B push-pull amplifier?

  1. 25%
  2. 50%
  3. 78.5%
  4. 95%
Show answer & solution

Answer: (C) 78.5%

Each transistor conducts for half a cycle.

Question 4

What distortion occurs in class B push-pull amplifiers?

  1. Harmonic resonance only
  2. Clipping only at low signals
  3. Frequency doubling
  4. Crossover distortion
Show answer & solution

Answer: (D) Crossover distortion

It is caused by the turn-on voltage of transistors near zero crossing.

Question 5

How does a class AB amplifier reduce crossover distortion?

  1. By biasing transistors slightly into conduction at zero signal
  2. By increasing supply voltage
  3. By using a capacitor
  4. By using only one transistor
Show answer & solution

Answer: (A) By biasing transistors slightly into conduction at zero signal

Diodes or VBE multipliers provide the small bias.

Question 6

Where are class C amplifiers mainly used?

  1. Instrumentation amplifiers
  2. Audio amplifiers
  3. Radio frequency tuned amplifiers and transmitters
  4. DC amplifiers
Show answer & solution

Answer: (C) Radio frequency tuned amplifiers and transmitters

They conduct for less than 180° and use tuned circuits to restore the waveform.

Question 7

What is the voltage gain in decibels of an amplifier with a voltage gain of 100?

  1. 10 dB
  2. 20 dB
  3. 40 dB
  4. 100 dB
Show answer & solution

Answer: (C) 40 dB

Gain(dB) = 20 log₁₀(100) = 40 dB.

Question 8

How is power gain expressed in decibels?

  1. log₁₀(Pin/Pout)
  2. 10 log₁₀(Pout/Pin)
  3. 20 log₁₀(Pout/Pin)
  4. Pout/Pin
Show answer & solution

Answer: (B) 10 log₁₀(Pout/Pin)

Voltage gain uses 20 log.

Question 9

How are the gains of cascaded amplifier stages combined when expressed in decibels?

  1. The smallest is taken
  2. They are divided
  3. They are multiplied
  4. They are added
Show answer & solution

Answer: (D) They are added

In ratio form, gains multiply.

Question 10

What is the gain–bandwidth product of an amplifier?

  1. The product of its gain and bandwidth, which stays approximately constant
  2. The sum of gain and bandwidth
  3. The ratio of gain to bandwidth
  4. The maximum gain only
Show answer & solution

Answer: (A) The product of its gain and bandwidth, which stays approximately constant

Increasing gain reduces bandwidth.

Question 11

What is the effect of negative feedback on amplifier gain and bandwidth?

  1. Gain decreases and bandwidth increases
  2. Both increase
  3. Both decrease
  4. Gain increases and bandwidth decreases
Show answer & solution

Answer: (A) Gain decreases and bandwidth increases

Negative feedback trades gain for performance.

Question 12

Which of these is an advantage of negative feedback in amplifiers?

  1. More distortion
  2. Higher gain
  3. Oscillation
  4. Reduced distortion and noise with more stable gain
Show answer & solution

Answer: (D) Reduced distortion and noise with more stable gain

Gain becomes nearly independent of transistor parameters.

Question 13

What does positive feedback in an amplifier tend to produce?

  1. Stable gain
  2. Oscillation or instability
  3. Wider bandwidth
  4. Lower distortion
Show answer & solution

Answer: (B) Oscillation or instability

Oscillators use controlled positive feedback.

Question 14

How does voltage-series negative feedback affect amplifier input and output impedance?

  1. It increases input impedance and decreases output impedance
  2. It has no effect
  3. It increases output impedance
  4. It decreases input impedance
Show answer & solution

Answer: (A) It increases input impedance and decreases output impedance

This makes the amplifier a better voltage amplifier.

Question 15

Which coupling method is used in amplifiers that must amplify DC signals?

  1. Capacitor coupling
  2. RC coupling
  3. Transformer coupling
  4. Direct coupling
Show answer & solution

Answer: (D) Direct coupling

Coupling capacitors block DC.

Question 16

What is the main advantage of RC-coupled amplifiers?

  1. Impedance matching
  2. Ability to amplify DC
  3. Low cost, small size and good audio frequency response
  4. Very high efficiency
Show answer & solution

Answer: (C) Low cost, small size and good audio frequency response

They are common in audio preamplifiers.

Question 17

What is the Miller effect?

  1. A decrease in output resistance
  2. The increase in effective input capacitance of an inverting amplifier due to feedback capacitance multiplied by gain
  3. An increase in noise
  4. A thermal effect
Show answer & solution

Answer: (B) The increase in effective input capacitance of an inverting amplifier due to feedback capacitance multiplied by gain

It limits high-frequency response.

Question 18

What are the lower and upper cut-off frequencies of an amplifier?

  1. The frequencies of maximum gain
  2. The frequencies at which gain is zero
  3. The resonance frequencies
  4. The frequencies at which gain falls to 0.707 of the mid-band value (−3 dB)
Show answer & solution

Answer: (D) The frequencies at which gain falls to 0.707 of the mid-band value (−3 dB)

Bandwidth is the difference between them.

Question 19

What does the common-mode rejection ratio (CMRR) of a differential amplifier measure?

  1. Its ability to reject signals common to both inputs relative to differential signals
  2. Its power gain
  3. Its output impedance
  4. Its bandwidth
Show answer & solution

Answer: (A) Its ability to reject signals common to both inputs relative to differential signals

High CMRR rejects noise picked up equally on both inputs.

Question 20

What is the main advantage of push-pull amplifier output stages?

  1. Need for one transistor only
  2. Higher distortion
  3. Higher efficiency and cancellation of even harmonics
  4. Lower power
Show answer & solution

Answer: (C) Higher efficiency and cancellation of even harmonics

Complementary push-pull stages are common in audio power amplifiers.

Question 21

Which amplifier class has the highest efficiency among class A, B and C?

  1. Class AB
  2. Class C
  3. Class A
  4. Class B
Show answer & solution

Answer: (B) Class C

Class C efficiency can exceed 80–90% in RF amplifiers.

Question 22

What is a class D amplifier?

  1. An oscillator
  2. A linear class A amplifier
  3. A switching amplifier that uses PWM to drive the output devices on and off
  4. A tube amplifier
Show answer & solution

Answer: (C) A switching amplifier that uses PWM to drive the output devices on and off

Efficiencies above 90% are possible.

Question 23

What is the bandwidth of an amplifier with lower and upper cut-off frequencies of 50 Hz and 20 kHz?

  1. About 19.95 kHz
  2. About 20.05 kHz
  3. 50 Hz
  4. 400 kHz
Show answer & solution

Answer: (A) About 19.95 kHz

Bandwidth = fH − fL.

Question 24

What is meant by the input impedance of an amplifier?

  1. The supply resistance
  2. The impedance seen by the signal source at the amplifier input
  3. The impedance of the load
  4. The output resistance
Show answer & solution

Answer: (B) The impedance seen by the signal source at the amplifier input

A high input impedance avoids loading the source.

Question 25

What is the effect of loading an amplifier output with a low resistance compared with its output impedance?

  1. There is no effect
  2. Gain becomes infinite
  3. The output voltage rises
  4. The output voltage falls significantly
Show answer & solution

Answer: (D) The output voltage falls significantly

Buffers with low output impedance prevent this.

Question 26

What is the voltage gain of two cascaded stages with gains of 20 dB and 30 dB?

  1. 1.5 dB
  2. 10 dB
  3. 50 dB
  4. 600 dB
Show answer & solution

Answer: (C) 50 dB

Decibel gains add.

Question 27

What does a gain of −3 dB correspond to in power?

  1. Double power
  2. Same power
  3. One quarter power
  4. Half power
Show answer & solution

Answer: (D) Half power

In voltage, −3 dB is 0.707 times.

Question 28

What is the purpose of a tuned amplifier?

  1. To amplify all frequencies equally
  2. To amplify a narrow band of frequencies around a resonant frequency
  3. To generate DC
  4. To rectify signals
Show answer & solution

Answer: (B) To amplify a narrow band of frequencies around a resonant frequency

Tuned amplifiers are used in radio receivers.

Question 29

What is harmonic distortion in an amplifier?

  1. Generation of frequency components that are multiples of the input frequency
  2. A fall in noise
  3. A change in DC level
  4. An increase in bandwidth
Show answer & solution

Answer: (A) Generation of frequency components that are multiples of the input frequency

It is caused by non-linear transfer characteristics.

Question 30

What is the effect of negative feedback on amplifier sensitivity to transistor parameter variations?

  1. There is no change
  2. The amplifier becomes less sensitive
  3. The amplifier stops working
  4. The amplifier becomes more sensitive
Show answer & solution

Answer: (B) The amplifier becomes less sensitive

With high loop gain, closed-loop gain depends mainly on the feedback network.

Practice these 30 questions interactively →