Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Electronics: Bipolar Transistors

Electrical Engineering · Electronics

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What are the three terminals of a bipolar junction transistor?

  1. Source, gate and drain
  2. Emitter, base and collector
  3. Input, output and ground only
  4. Anode, cathode and gate
Show answer & solution

Answer: (B) Emitter, base and collector

BJTs can be NPN or PNP.

Question 2

Why is the base of a BJT made thin and lightly doped?

  1. So that most carriers from the emitter pass through to the collector
  2. To reduce collector current
  3. To make it a good insulator
  4. To increase base current
Show answer & solution

Answer: (A) So that most carriers from the emitter pass through to the collector

This gives high current gain.

Question 3

Which region of a BJT is the most heavily doped?

  1. All are equal
  2. Collector
  3. Base
  4. Emitter
Show answer & solution

Answer: (D) Emitter

The emitter supplies majority carriers.

Question 4

What is the relationship between emitter, base and collector currents of a BJT?

  1. IE = IB − IC
  2. IB = IC + IE
  3. IC = IB + IE
  4. IE = IB + IC
Show answer & solution

Answer: (D) IE = IB + IC

This follows from KCL.

Question 5

How is the DC current gain β of a BJT defined?

  1. IB/IC
  2. IC/IE
  3. IC/IB
  4. IE/IB
Show answer & solution

Answer: (C) IC/IB

β is typically between 50 and 300.

Question 6

How is α related to β for a BJT?

  1. β = α/(1 − α)
  2. β = α + 1
  3. β = α(1 − α)
  4. β = 1/α
Show answer & solution

Answer: (A) β = α/(1 − α)

α is the common-base current gain, slightly less than 1.

Question 7

What is the value of β if α = 0.98?

  1. 0.98
  2. 49
  3. 50.5
  4. 98
Show answer & solution

Answer: (B) 49

β = 0.98/0.02 = 49.

Question 8

What is the collector current of a transistor with β = 100 and a base current of 20 µA?

  1. 0.2 mA
  2. 2 mA
  3. 20 mA
  4. 200 mA
Show answer & solution

Answer: (B) 2 mA

IC = β × IB = 100 × 20 µA.

Question 9

Which amplifier configuration normally provides high voltage gain with phase reversal?

  1. Voltage-follower amplifier
  2. Common-collector amplifier
  3. Common-emitter amplifier
  4. Common-drain amplifier
Show answer & solution

Answer: (C) Common-emitter amplifier

The output is 180° out of phase with the input.

Question 10

What is the main feature of a common-collector (emitter follower) amplifier?

  1. Voltage gain close to one with high input and low output impedance
  2. Phase reversal
  3. Low input impedance
  4. Very high voltage gain
Show answer & solution

Answer: (A) Voltage gain close to one with high input and low output impedance

It is used as a buffer.

Question 11

What is the main feature of a common-base amplifier?

  1. Phase reversal
  2. Current gain much greater than one
  3. Very high input impedance
  4. Low input impedance and good high-frequency response
Show answer & solution

Answer: (D) Low input impedance and good high-frequency response

Its current gain is slightly less than one.

Question 12

In which region must a BJT operate to work as a linear amplifier?

  1. Breakdown region
  2. Saturation region
  3. Active region, with base–emitter forward biased and base–collector reverse biased
  4. Cut-off region
Show answer & solution

Answer: (C) Active region, with base–emitter forward biased and base–collector reverse biased

The Q-point is set in the middle of the active region.

Question 13

In which regions does a BJT operate when used as a switch?

  1. Active region only
  2. Breakdown only
  3. Reverse active only
  4. Saturation (on) and cut-off (off)
Show answer & solution

Answer: (D) Saturation (on) and cut-off (off)

Switching minimises power dissipation.

Question 14

Why is a voltage divider network commonly used in transistor biasing circuits?

  1. To establish a stable base voltage that makes the operating point less dependent on β
  2. To increase output frequency
  3. To remove collector current
  4. To produce positive feedback
Show answer & solution

Answer: (A) To establish a stable base voltage that makes the operating point less dependent on β

An emitter resistor adds further stability.

Question 15

What is the DC load line of a transistor amplifier?

  1. A graph of input impedance
  2. A line on the output characteristics showing all possible IC–VCE values for the given supply and load
  3. A graph of temperature
  4. A graph of gain against frequency
Show answer & solution

Answer: (B) A line on the output characteristics showing all possible IC–VCE values for the given supply and load

The Q-point lies on the load line.

Question 16

What is thermal runaway in a BJT?

  1. A fall in temperature
  2. An increase in β only at low temperature
  3. A cumulative increase in collector current and temperature that can destroy the transistor
  4. Normal switching
Show answer & solution

Answer: (C) A cumulative increase in collector current and temperature that can destroy the transistor

Proper biasing and heat sinking prevent it.

Question 17

What is the typical collector–emitter voltage of a saturated silicon BJT?

  1. About 0.2 V
  2. About 0.7 V always
  3. About 5 V
  4. About 12 V
Show answer & solution

Answer: (A) About 0.2 V

A saturated transistor acts like a closed switch.

Question 18

What is the Early effect in a BJT?

  1. Light sensitivity
  2. Zero current at high voltage
  3. Early breakdown
  4. Variation of effective base width with collector voltage, causing collector current to rise slightly with VCE
Show answer & solution

Answer: (D) Variation of effective base width with collector voltage, causing collector current to rise slightly with VCE

It gives the output characteristics a finite slope.

Question 19

What is a Darlington pair?

  1. Two diodes in series
  2. Two transistors connected so that the overall current gain is about the product of their gains
  3. A transistor with a capacitor
  4. An op-amp
Show answer & solution

Answer: (B) Two transistors connected so that the overall current gain is about the product of their gains

Darlington pairs give very high current gain.

Question 20

Which h-parameter represents the current gain of a common-emitter transistor?

  1. hie
  2. hfe
  3. hoe
  4. hre
Show answer & solution

Answer: (B) hfe

hie is input impedance and hoe output admittance.

Question 21

What is the stability factor S in transistor biasing a measure of?

  1. The voltage gain
  2. The power gain
  3. How much collector current changes with changes in leakage current
  4. The bandwidth
Show answer & solution

Answer: (C) How much collector current changes with changes in leakage current

A low stability factor means better bias stability.

Question 22

What is the main disadvantage of fixed (base resistor) bias?

  1. It is too complex
  2. It gives zero gain
  3. It needs two supplies
  4. The operating point depends strongly on β and temperature
Show answer & solution

Answer: (D) The operating point depends strongly on β and temperature

Voltage divider bias is preferred.

Question 23

Which transistor configuration is most commonly used for voltage amplification?

  1. Common emitter
  2. Common base
  3. Common collector
  4. Common drain
Show answer & solution

Answer: (A) Common emitter

It gives both voltage and current gain.

Question 24

What is the voltage across the base–emitter junction of a conducting silicon BJT?

  1. About 0.1 V
  2. About 0.7 V
  3. About 5 V
  4. About 12 V
Show answer & solution

Answer: (B) About 0.7 V

VBE is nearly constant in the active region.

Question 25

What is a phototransistor?

  1. A Zener diode
  2. A high-power switch
  3. A transistor whose base current is produced by incident light
  4. A transistor with a light-emitting junction
Show answer & solution

Answer: (C) A transistor whose base current is produced by incident light

Phototransistors are used in optocouplers and sensors.

Question 26

What is the main application of a transistor operated in the active region?

  1. Linear amplification
  2. Light emission
  3. Digital switching only
  4. Rectification
Show answer & solution

Answer: (A) Linear amplification

In the active region, IC is controlled by IB.

Question 27

What is the effect of an unbypassed emitter resistor on a common-emitter amplifier?

  1. It causes oscillation
  2. It increases voltage gain
  3. It reduces voltage gain but improves stability and input impedance
  4. It removes biasing
Show answer & solution

Answer: (C) It reduces voltage gain but improves stability and input impedance

A bypass capacitor restores AC gain.

Question 28

What is the purpose of coupling capacitors in a BJT amplifier?

  1. To store DC
  2. To pass AC signals while blocking DC between stages
  3. To set the Q-point
  4. To regulate voltage
Show answer & solution

Answer: (B) To pass AC signals while blocking DC between stages

They prevent stages from upsetting each other's bias.

Question 29

What is the purpose of an emitter bypass capacitor?

  1. To block DC
  2. To bias the base
  3. To short the emitter resistor for AC and increase voltage gain
  4. To filter the supply
Show answer & solution

Answer: (C) To short the emitter resistor for AC and increase voltage gain

It does not affect DC bias.

Question 30

What is the approximate collector current of a transistor whose emitter current is 5 mA and α is 0.99?

  1. 0.05 mA
  2. 4.5 mA
  3. 4.95 mA
  4. 5.05 mA
Show answer & solution

Answer: (C) 4.95 mA

IC = α × IE = 0.99 × 5 = 4.95 mA.

Practice these 30 questions interactively →