Why is a field-effect transistor called a unipolar device?
Show answer & solution
Answer: (D) Current is carried by only one type of carrier
BJTs use both electrons and holes.
Electrical Engineering · Electronics
28 questions, each with the answer and a worked solution.
Practice interactively and track your score →Why is a field-effect transistor called a unipolar device?
Answer: (D) Current is carried by only one type of carrier
BJTs use both electrons and holes.
How is a JFET controlled?
Answer: (A) By the gate–source voltage, which changes the channel width
The gate junction is reverse biased.
What is the main advantage of a FET over a BJT as an amplifier input?
Answer: (D) Very high input impedance
FETs draw almost no gate current.
What is the pinch-off voltage of a JFET?
Answer: (B) The gate–source voltage at which the channel is fully closed and drain current is cut off
For an n-channel JFET it is negative.
What is Shockley's equation for JFET drain current?
Answer: (C) ID = IDSS(1 − VGS/VP)²
IDSS is the drain current with VGS = 0.
What is the drain current of a JFET with IDSS = 10 mA, VP = −4 V and VGS = −2 V?
Answer: (B) 2.5 mA
ID = 10(1 − 0.5)² = 2.5 mA.
What is the main difference between enhancement and depletion MOSFETs?
Answer: (A) An enhancement MOSFET has no channel at zero gate voltage, while a depletion MOSFET has one
Most power and digital MOSFETs are enhancement type.
What gate voltage does an n-channel enhancement MOSFET need to conduct?
Answer: (C) A positive gate–source voltage above its threshold voltage
The positive gate attracts electrons to form an inversion channel.
Why does CMOS logic consume very little static power?
Answer: (D) One transistor in each complementary pair is always off, so no DC path exists from supply to ground
Power is consumed mainly during switching.
What is transconductance (gm) of a FET?
Answer: (A) The change in drain current divided by the change in gate–source voltage
It measures the gain capability of the FET.
Which FET amplifier configuration gives phase reversal and voltage gain?
Answer: (C) Common source
It is similar to the common-emitter BJT stage.
What is the common-drain FET amplifier also called?
Answer: (B) Source follower
Its voltage gain is slightly less than one.
Why must MOSFETs be handled with care against static electricity?
Answer: (A) The thin gate oxide can be destroyed by electrostatic discharge
Antistatic handling and gate protection diodes are used.
What is the main advantage of FETs over BJTs regarding noise?
Answer: (D) FETs generally produce less noise at high source impedances
Low-noise preamplifiers often use FET inputs.
What is the region of operation of a MOSFET when used as an amplifier?
Answer: (B) Saturation (active) region
In MOSFETs, saturation means drain current is nearly independent of VDS.
In which region does a MOSFET behave like a voltage-controlled resistor?
Answer: (D) Ohmic (triode) region
Switching MOSFETs operate in the ohmic region when on.
What is the gate current of a MOSFET under DC conditions?
Answer: (A) Practically zero
The gate is insulated by an oxide layer.
What is the function of the substrate (body) terminal of a MOSFET?
Answer: (C) It forms the base region in which the channel is induced and is often connected to the source
The body effect changes threshold voltage.
Why are MOSFETs dominant in modern digital integrated circuits?
Answer: (D) They can be made very small, use little power in CMOS and are easy to integrate in large numbers
Billions of MOSFETs are integrated on modern chips.
What does the threshold voltage of an enhancement MOSFET mean?
Answer: (A) The minimum gate–source voltage needed to form a conducting channel
Typical values range from about 1 to 4 V.
What is a cascode amplifier?
Answer: (C) A common-source or common-emitter stage followed by a common-gate or common-base stage for wide bandwidth
It reduces the Miller effect.
What is the main use of a power MOSFET in modern circuits?
Answer: (C) High-speed switching in power supplies and motor drives
Low on-resistance minimises conduction loss.
What is the depletion-mode MOSFET's drain current at zero gate voltage?
Answer: (D) Non-zero, because a channel already exists
A negative gate voltage reduces the current in an n-channel device.
What is the voltage gain of a common-source amplifier approximately?
Answer: (B) −gm × RD
The negative sign indicates phase inversion.
What is the voltage gain of a common-source amplifier with gm = 4 mS and RD = 5 kΩ?
Answer: (A) −20
Av = −4 × 10⁻³ × 5,000 = −20.
What does a p-channel MOSFET need to conduct in enhancement mode?
Answer: (C) A negative gate–source voltage beyond its threshold
Holes form the channel.
What is the main benefit of MOSFETs in battery-operated devices?
Answer: (D) Low gate drive power and efficient switching
They extend battery life in phones and laptops.
What is the typical input impedance of a MOSFET amplifier?
Answer: (D) Extremely high, often above 10¹⁰ Ω
The insulated gate draws negligible current.