Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Control Systems: Controllers and State Space

Electrical Engineering · Control Systems

26 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the effect of proportional (P) control?

  1. It predicts future error
  2. It has no effect
  3. It eliminates steady-state error completely
  4. It produces control action proportional to error, improving speed but leaving steady-state error in type-0 systems
Show answer & solution

Answer: (D) It produces control action proportional to error, improving speed but leaving steady-state error in type-0 systems

Increasing Kp reduces error but may cause overshoot.

Question 2

What is the main effect of adding integral action to a controller?

  1. It improves noise immunity only
  2. It reduces system type
  3. It increases steady-state error
  4. It eliminates steady-state error to step inputs
Show answer & solution

Answer: (D) It eliminates steady-state error to step inputs

It adds a pole at the origin.

Question 3

What is the main effect of derivative action in a controller?

  1. It increases overshoot
  2. It improves damping and stability by responding to the rate of change of error
  3. It eliminates steady-state error
  4. It has no effect
Show answer & solution

Answer: (B) It improves damping and stability by responding to the rate of change of error

It is sensitive to measurement noise.

Question 4

What does PID stand for in control systems?

  1. Primary input device
  2. Phase integral difference
  3. Power induction drive
  4. Proportional–integral–derivative
Show answer & solution

Answer: (D) Proportional–integral–derivative

PID controllers are the most widely used industrial controllers.

Question 5

Which classical method gives initial PID settings from the ultimate gain and period of oscillation?

  1. Ziegler–Nichols tuning method
  2. Bode method
  3. Mason's rule
  4. Routh method
Show answer & solution

Answer: (A) Ziegler–Nichols tuning method

It is a practical starting point for tuning.

Question 6

What does a phase-lead compensator mainly improve?

  1. Steady-state error only
  2. Transient response and phase margin
  3. Low-frequency gain only
  4. Noise rejection only
Show answer & solution

Answer: (B) Transient response and phase margin

It adds positive phase near crossover.

Question 7

What does a phase-lag compensator mainly improve?

  1. Transient speed
  2. Phase margin directly
  3. Steady-state accuracy by raising low-frequency gain
  4. Bandwidth
Show answer & solution

Answer: (C) Steady-state accuracy by raising low-frequency gain

It may slow the transient response.

Question 8

What is integral windup?

  1. Excessive accumulation of the integral term when the actuator is saturated, causing large overshoot
  2. A type of noise
  3. A fault in derivative action
  4. A mechanical problem in motors
Show answer & solution

Answer: (A) Excessive accumulation of the integral term when the actuator is saturated, causing large overshoot

Anti-windup schemes limit the integral term.

Question 9

How is a system represented in state-space form?

  1. y = Gx only
  2. y = Ax
  3. ẋ = u only
  4. ẋ = Ax + Bu and y = Cx + Du
Show answer & solution

Answer: (D) ẋ = Ax + Bu and y = Cx + Du

It handles multiple inputs and outputs naturally.

Question 10

What do the eigenvalues of the state matrix A represent?

  1. The zeros of the system
  2. The inputs
  3. The poles of the system
  4. The outputs
Show answer & solution

Answer: (C) The poles of the system

Stable systems have eigenvalues with negative real parts.

Question 11

What is controllability of a system?

  1. The steady-state error
  2. The ability to move the system from any initial state to any final state with suitable inputs
  3. The stability of the system
  4. The ability to measure all states
Show answer & solution

Answer: (B) The ability to move the system from any initial state to any final state with suitable inputs

Kalman's controllability matrix tests it.

Question 12

What is observability of a system?

  1. The ability to control states
  2. The stability margin
  3. The system type
  4. The ability to determine all states from the outputs over time
Show answer & solution

Answer: (D) The ability to determine all states from the outputs over time

Observers estimate unmeasured states.

Question 13

What device is commonly used for sequential and logic control in industrial automation?

  1. Wheatstone bridge
  2. Spectrum analyser
  3. Programmable logic controller (PLC)
  4. Oscilloscope
Show answer & solution

Answer: (C) Programmable logic controller (PLC)

PLCs are programmed with ladder logic and other languages.

Question 14

What is feedforward control?

  1. Control using only output feedback
  2. Control that measures a disturbance and acts before it affects the output
  3. Derivative control
  4. Open-loop control without any measurement
Show answer & solution

Answer: (B) Control that measures a disturbance and acts before it affects the output

It is often combined with feedback control.

Question 15

What is cascade control?

  1. A control scheme using an inner fast loop within an outer slower loop
  2. A single-loop controller
  3. On–off control only
  4. Open-loop control
Show answer & solution

Answer: (A) A control scheme using an inner fast loop within an outer slower loop

Motor drives use inner current loops and outer speed loops.

Question 16

Which transform is used for analysing digital (discrete-time) control systems?

  1. Laplace transform only
  2. Fourier series only
  3. Z-transform
  4. Clarke transform
Show answer & solution

Answer: (C) Z-transform

The z-plane unit circle defines stability for discrete systems.

Question 17

Where must the poles of a stable discrete-time system lie?

  1. On the imaginary axis
  2. Outside the unit circle
  3. In the right half of the s-plane
  4. Inside the unit circle in the z-plane
Show answer & solution

Answer: (D) Inside the unit circle in the z-plane

A magnitude of z below 1 corresponds to the left half s-plane.

Question 18

Which sensor is commonly used to provide speed feedback in DC motor speed control?

  1. Thermocouple
  2. Tachogenerator or encoder
  3. Strain gauge
  4. LDR
Show answer & solution

Answer: (B) Tachogenerator or encoder

Feedback allows accurate speed regulation.

Question 19

What is the transfer function of an ideal PID controller?

  1. Kp + Ki/s + Kd s
  2. Kp × Ki × Kd
  3. Kd/s
  4. Kp/s
Show answer & solution

Answer: (A) Kp + Ki/s + Kd s

Practical PID controllers filter the derivative term.

Question 20

What is the main disadvantage of on–off control?

  1. It never switches
  2. It is too complex
  3. It causes continuous cycling of the controlled variable around the set point
  4. It is very expensive
Show answer & solution

Answer: (C) It causes continuous cycling of the controlled variable around the set point

A dead band reduces switching frequency.

Question 21

What is the effect of increasing the integral gain too much in a PI controller?

  1. Removal of integral action
  2. Faster settling with no overshoot always
  3. More oscillation and possible instability
  4. Zero overshoot
Show answer & solution

Answer: (C) More oscillation and possible instability

Integral action adds phase lag.

Question 22

What is a PD controller's transfer function?

  1. Kp + Kd s
  2. Kp + Ki/s
  3. Ki/s
  4. Kp/s
Show answer & solution

Answer: (A) Kp + Kd s

It adds a zero that improves damping.

Question 23

What is the state transition matrix used for?

  1. Plotting Bode diagrams
  2. Measuring errors
  3. Finding zeros
  4. Finding the solution of the state equations over time
Show answer & solution

Answer: (D) Finding the solution of the state equations over time

It equals e^(At) for LTI systems.

Question 24

What is pole placement in state feedback control?

  1. Choosing feedback gains to place closed-loop poles at desired locations
  2. Using only open-loop control
  3. Placing sensors
  4. Moving zeros
Show answer & solution

Answer: (A) Choosing feedback gains to place closed-loop poles at desired locations

It requires the system to be controllable.

Question 25

Which controller action is mainly responsible for anticipating future error?

  1. Proportional action
  2. Integral action
  3. Derivative action
  4. On–off action
Show answer & solution

Answer: (C) Derivative action

It responds to the slope of the error.

Question 26

What type of control is commonly used in a modern inverter air conditioner to hold room temperature?

  1. Manual control
  2. Open-loop timer control
  3. Simple on–off control only
  4. Closed-loop variable-speed control of the compressor
Show answer & solution

Answer: (D) Closed-loop variable-speed control of the compressor

Variable-speed control reduces temperature swings and energy use.

Practice these 26 questions interactively →