Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Mass Transfer: Gas Absorption

Chemical Engineering · Mass Transfer

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is gas absorption?

  1. Removal of a solute from liquid to gas
  2. Removal of liquid from a solid
  3. Separation of liquids by boiling
  4. Transfer of a soluble component from a gas mixture into a liquid solvent
Show answer & solution

Answer: (D) Transfer of a soluble component from a gas mixture into a liquid solvent

Stripping is the reverse operation.

Question 2

What is stripping (desorption)?

  1. Absorption into a liquid
  2. Drying of solids
  3. Removal of a dissolved gas from a liquid by contact with an inert gas or steam
  4. Crystallisation
Show answer & solution

Answer: (C) Removal of a dissolved gas from a liquid by contact with an inert gas or steam

Sour-water strippers remove H₂S and NH₃.

Question 3

Which solvent is widely used in Pakistani gas-processing plants to remove CO₂ and H₂S from natural gas?

  1. Aqueous amine solutions such as MDEA or DEA
  2. Pure water only
  3. Benzene
  4. Mercury
Show answer & solution

Answer: (A) Aqueous amine solutions such as MDEA or DEA

Sui and Qadirpur gas processing includes amine treating.

Question 4

What is the purpose of glycol dehydration units in natural gas processing?

  1. To remove sulphur
  2. To remove CO₂
  3. To add odour
  4. To absorb water vapour from the gas using triethylene glycol
Show answer & solution

Answer: (D) To absorb water vapour from the gas using triethylene glycol

Dry gas avoids hydrate formation and corrosion.

Question 5

What does the operating line represent in absorption?

  1. The flooding limit
  2. The relationship between bulk gas and liquid compositions at any point in the column from a material balance
  3. The equilibrium curve
  4. The pressure drop
Show answer & solution

Answer: (B) The relationship between bulk gas and liquid compositions at any point in the column from a material balance

For dilute systems it is a straight line with slope L/G.

Question 6

Where does the operating line lie for absorption relative to the equilibrium curve on a y–x diagram?

  1. On the equilibrium curve
  2. It has no position
  3. Above the equilibrium curve
  4. Below the equilibrium curve
Show answer & solution

Answer: (C) Above the equilibrium curve

For stripping it lies below the curve.

Question 7

What is the minimum liquid-to-gas ratio in absorption?

  1. The ratio at which the operating line touches the equilibrium curve, needing infinite height
  2. The ratio of zero liquid flow
  3. The ratio at flooding
  4. The ratio for maximum pressure drop
Show answer & solution

Answer: (A) The ratio at which the operating line touches the equilibrium curve, needing infinite height

Actual L/G is usually 1.2 to 2 times the minimum.

Question 8

What is the absorption factor A?

  1. G/L
  2. L × G
  3. mG/L
  4. L/(mG), where m is the slope of the equilibrium line
Show answer & solution

Answer: (D) L/(mG), where m is the slope of the equilibrium line

Values of about 1.25–2 are economical.

Question 9

Which equation gives the number of ideal stages for absorption with straight operating and equilibrium lines?

  1. Rayleigh equation
  2. Kremser equation
  3. Fenske equation
  4. Underwood equation
Show answer & solution

Answer: (B) Kremser equation

It uses the absorption factor A.

Question 10

What is HTU in packed column design?

  1. Heat transfer unit
  2. Hydraulic transfer unit
  3. Height of tower used
  4. Height of a transfer unit
Show answer & solution

Answer: (D) Height of a transfer unit

Packed height Z = HTU × NTU.

Question 11

What does NTU measure in packed column design?

  1. The column height directly
  2. The packing size
  3. The difficulty of the separation in terms of driving force
  4. The liquid viscosity
Show answer & solution

Answer: (C) The difficulty of the separation in terms of driving force

It is an integral of dy/(y − y*).

Question 12

What is HETP?

  1. Height equivalent to a theoretical plate
  2. Heat exchanged per theoretical plate
  3. Height of efficient tray packing
  4. Height of empty tower packing
Show answer & solution

Answer: (A) Height equivalent to a theoretical plate

Packed height = HETP × number of theoretical stages.

Question 13

What is flooding in a packed column?

  1. Weeping
  2. Accumulation of liquid when gas flow is so high that liquid cannot flow down
  3. Dry packing
  4. Low liquid flow
Show answer & solution

Answer: (B) Accumulation of liquid when gas flow is so high that liquid cannot flow down

Columns are designed at about 60–80% of flooding velocity.

Question 14

What is loading in a packed column?

  1. The initial wetting
  2. The point where liquid holdup begins to increase noticeably with gas flow
  3. Zero flow
  4. The flooding point
Show answer & solution

Answer: (B) The point where liquid holdup begins to increase noticeably with gas flow

Loading occurs below flooding.

Question 15

What is channelling in a packed column?

  1. Uniform distribution
  2. Flooding
  3. Liquid flowing down preferential paths, leaving packing poorly wetted
  4. Weeping
Show answer & solution

Answer: (C) Liquid flowing down preferential paths, leaving packing poorly wetted

Good distributors and redistributors reduce it.

Question 16

Why are liquid redistributors placed at intervals in tall packed columns?

  1. To counter liquid migration to the walls and maintain good distribution
  2. To heat the liquid
  3. To remove gas
  4. To support the packing
Show answer & solution

Answer: (A) To counter liquid migration to the walls and maintain good distribution

They are often placed every 3–6 m or several column diameters.

Question 17

What property should a good tower packing have?

  1. High pressure drop
  2. Low void fraction
  3. Low surface area
  4. Large surface area per volume with high void fraction and low pressure drop
Show answer & solution

Answer: (D) Large surface area per volume with high void fraction and low pressure drop

Raschig rings, Pall rings and structured packings are used.

Question 18

Which packing is the oldest simple type of random packing?

  1. Intalox saddle
  2. Raschig ring
  3. Pall ring
  4. Structured packing
Show answer & solution

Answer: (B) Raschig ring

Pall rings have windows that improve performance.

Question 19

What is the advantage of structured packing over random packing?

  1. Lower cost always
  2. Higher pressure drop
  3. Higher efficiency and lower pressure drop
  4. Better for dirty liquids
Show answer & solution

Answer: (C) Higher efficiency and lower pressure drop

It is widely used in vacuum distillation.

Question 20

Why does absorption favour high pressure and low temperature?

  1. Gas solubility increases with pressure and decreases with temperature
  2. Temperature has no effect
  3. Pressure reduces solubility
  4. Solubility increases with temperature
Show answer & solution

Answer: (A) Gas solubility increases with pressure and decreases with temperature

Stripping favours low pressure and high temperature.

Question 21

What is a spray tower?

  1. A dryer
  2. A tray column
  3. A packed column
  4. A column in which liquid is sprayed into a rising gas stream
Show answer & solution

Answer: (D) A column in which liquid is sprayed into a rising gas stream

It has low pressure drop but low efficiency.

Question 22

What is a venturi scrubber mainly used for?

  1. Crystallisation
  2. Drying
  3. Distillation
  4. Removing fine particles and soluble gases from gas by high-velocity contact with liquid
Show answer & solution

Answer: (D) Removing fine particles and soluble gases from gas by high-velocity contact with liquid

It has high pressure drop.

Question 23

Which process absorbs SO₃ in sulphuric acid manufacture?

  1. Distillation
  2. Absorption in pure water
  3. Absorption in 98–99% sulphuric acid
  4. Adsorption on carbon
Show answer & solution

Answer: (C) Absorption in 98–99% sulphuric acid

Absorbing SO₃ directly in water forms an acid mist.

Question 24

What is a bubble cap tray?

  1. A tray with caps over risers that force gas to bubble through the liquid
  2. A sieve plate without holes
  3. A packed bed
  4. A spray nozzle
Show answer & solution

Answer: (A) A tray with caps over risers that force gas to bubble through the liquid

It works at low flows but is costly.

Question 25

What is the Henry's law constant used for in absorption?

  1. Finding viscosity
  2. Describing the equilibrium relation between gas partial pressure and liquid concentration
  3. Calculating heat transfer
  4. Finding the boiling point
Show answer & solution

Answer: (B) Describing the equilibrium relation between gas partial pressure and liquid concentration

p = H x for dilute solutions.

Question 26

What happens to absorption if the operating line slope L/G is increased?

  1. The driving force increases and fewer stages are needed
  2. More stages are needed
  3. Absorption stops
  4. The driving force decreases
Show answer & solution

Answer: (A) The driving force increases and fewer stages are needed

Higher liquid rate raises solvent cost.

Question 27

What is the chemical reaction effect in absorption with reaction?

  1. It makes absorption impossible
  2. It has no effect
  3. It decreases the rate
  4. It increases the absorption rate compared with physical absorption
Show answer & solution

Answer: (D) It increases the absorption rate compared with physical absorption

The enhancement factor expresses this effect.

Question 28

What is the purpose of the liquid distributor at the top of a packed column?

  1. To cool the gas
  2. To support the packing
  3. To spread liquid evenly over the packing
  4. To remove gas
Show answer & solution

Answer: (C) To spread liquid evenly over the packing

Poor distribution reduces efficiency greatly.

Question 29

How does the number of transfer units change when the absorption factor approaches 1 for a high recovery?

  1. It decreases to zero
  2. It is unaffected
  3. It becomes negative
  4. It increases greatly
Show answer & solution

Answer: (D) It increases greatly

Driving forces become small along the column.

Question 30

What is the Benfield (hot potassium carbonate) process used for?

  1. Removing CO₂ from synthesis gas in ammonia plants
  2. Drying gases
  3. Desalting crude oil
  4. Removing water from ethanol
Show answer & solution

Answer: (A) Removing CO₂ from synthesis gas in ammonia plants

Activated potassium carbonate solutions absorb CO₂ at high temperature.

Practice these 30 questions interactively →