Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Mass Transfer: Extraction and Leaching

Chemical Engineering · Mass Transfer

26 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is liquid–liquid extraction?

  1. Separation by crystallisation
  2. Separation by boiling
  3. Separation of a component from a liquid by contact with an immiscible solvent in which it is more soluble
  4. Separation by filtration
Show answer & solution

Answer: (C) Separation of a component from a liquid by contact with an immiscible solvent in which it is more soluble

It is useful when distillation is difficult or costly.

Question 2

What is the raffinate in liquid–liquid extraction?

  1. The solid residue
  2. The feed phase remaining after the solute has been extracted
  3. The solvent-rich product phase
  4. The pure solvent
Show answer & solution

Answer: (B) The feed phase remaining after the solute has been extracted

The extract is the solvent-rich phase.

Question 3

What is the distribution (partition) coefficient?

  1. The selectivity of a membrane
  2. The ratio of flow rates
  3. The ratio of densities
  4. The ratio of solute concentration in the extract phase to that in the raffinate phase at equilibrium
Show answer & solution

Answer: (D) The ratio of solute concentration in the extract phase to that in the raffinate phase at equilibrium

A high value means less solvent is needed.

Question 4

What is selectivity in extraction?

  1. The ratio of distribution coefficients of the solute and the carrier liquid
  2. The ratio of solvent to feed
  3. The density difference
  4. The viscosity ratio
Show answer & solution

Answer: (A) The ratio of distribution coefficients of the solute and the carrier liquid

It must exceed 1 for separation.

Question 5

Which diagram is commonly used to represent ternary liquid–liquid equilibrium?

  1. Triangular diagram
  2. Psychrometric chart
  3. Moody chart
  4. Mollier diagram
Show answer & solution

Answer: (A) Triangular diagram

Tie lines connect equilibrium phases.

Question 6

What is the plait point on a ternary diagram?

  1. The point of pure solute
  2. The point of pure solvent
  3. The feed point
  4. The point where the two liquid phases become identical in composition
Show answer & solution

Answer: (D) The point where the two liquid phases become identical in composition

Tie lines shrink to zero length there.

Question 7

What is a desirable property of an extraction solvent?

  1. Complete miscibility with the feed
  2. High selectivity, immiscibility with the feed, and easy recovery
  3. High toxicity
  4. Same density as the feed
Show answer & solution

Answer: (B) High selectivity, immiscibility with the feed, and easy recovery

Density difference helps phase separation.

Question 8

Which equipment is commonly used for liquid–liquid extraction?

  1. Ball mills
  2. Cyclones
  3. Mixer–settlers, packed or rotating disc columns and centrifugal extractors
  4. Rotary dryers
Show answer & solution

Answer: (C) Mixer–settlers, packed or rotating disc columns and centrifugal extractors

Agitated columns improve contact.

Question 9

Why is countercurrent multistage extraction preferred to crosscurrent extraction?

  1. It gives no extract
  2. It needs more solvent
  3. It needs more stages always
  4. It achieves a given recovery with less solvent
Show answer & solution

Answer: (D) It achieves a given recovery with less solvent

Fresh solvent meets the most depleted raffinate.

Question 10

Which aromatic extraction process uses solvents such as sulfolane in refineries?

  1. Vacuum distillation
  2. Crude desalting
  3. Aromatics extraction from reformate
  4. Sulphur recovery
Show answer & solution

Answer: (C) Aromatics extraction from reformate

Benzene, toluene and xylene are extracted from reformate.

Question 11

What is supercritical fluid extraction?

  1. Extraction at very low pressure
  2. Extraction using a fluid above its critical temperature and pressure, often CO₂
  3. Extraction with water at room temperature
  4. Distillation under vacuum
Show answer & solution

Answer: (B) Extraction using a fluid above its critical temperature and pressure, often CO₂

Decaffeination of coffee uses supercritical CO₂.

Question 12

What is leaching?

  1. Extraction of a soluble component from a solid by a liquid solvent
  2. Separation of two liquids
  3. Drying of solids
  4. Absorption of gases
Show answer & solution

Answer: (A) Extraction of a soluble component from a solid by a liquid solvent

Sugar extraction from beet and oil from seeds are examples.

Question 13

What is the underflow in a leaching stage?

  1. The fresh solvent
  2. The clear solution only
  3. The vapour
  4. The solids together with the solution retained by them
Show answer & solution

Answer: (D) The solids together with the solution retained by them

The overflow is the clear solution.

Question 14

Which solvent is commonly used to extract edible oil from seed cake such as cottonseed and soybean?

  1. Sulphuric acid
  2. Water
  3. Hexane
  4. Mercury
Show answer & solution

Answer: (C) Hexane

The solvent is recovered by evaporation and steam stripping.

Question 15

What factors increase the rate of leaching?

  1. Smaller particle size, higher temperature and agitation
  2. Stagnant solvent
  3. Larger particles
  4. Lower temperature
Show answer & solution

Answer: (A) Smaller particle size, higher temperature and agitation

Too fine particles can make drainage difficult.

Question 16

What is a Bollman extractor?

  1. A cyclone
  2. A continuous moving-bucket extractor used for oilseeds
  3. A distillation column
  4. A dryer
Show answer & solution

Answer: (B) A continuous moving-bucket extractor used for oilseeds

Solvent percolates through baskets of flakes.

Question 17

What is the ideal stage concept in leaching?

  1. A stage where overflow solution has the same composition as solution in the underflow
  2. A stage with no contact
  3. A stage with no solids
  4. A stage with complete solvent removal
Show answer & solution

Answer: (A) A stage where overflow solution has the same composition as solution in the underflow

Stage efficiency accounts for incomplete equilibrium.

Question 18

What is heap leaching used for in mining?

  1. Crushing ore
  2. Separating gases
  3. Extracting metals such as gold or copper by percolating solutions through ore heaps
  4. Drying ore
Show answer & solution

Answer: (C) Extracting metals such as gold or copper by percolating solutions through ore heaps

Cyanide is used for gold and sulphuric acid for copper oxide ores.

Question 19

What is the solvent-to-feed ratio's effect on extraction?

  1. It has no effect
  2. It removes the need for stages
  3. Higher ratios decrease recovery
  4. Higher ratios increase recovery but raise solvent recovery costs
Show answer & solution

Answer: (D) Higher ratios increase recovery but raise solvent recovery costs

An optimum ratio is found economically.

Question 20

What is the purpose of a settler in a mixer–settler unit?

  1. To heat the feed
  2. To allow the two liquid phases to separate by gravity
  3. To remove solids only
  4. To mix the phases
Show answer & solution

Answer: (B) To allow the two liquid phases to separate by gravity

Mixers provide contact and settlers provide separation.

Question 21

What is the extract in liquid–liquid extraction?

  1. The solvent-rich phase containing the extracted solute
  2. The pure carrier liquid
  3. The feed after extraction
  4. The solid residue
Show answer & solution

Answer: (A) The solvent-rich phase containing the extracted solute

Solvent is later recovered from the extract.

Question 22

What is the effect of temperature on the two-phase region of most ternary liquid systems?

  1. The two-phase region usually shrinks as temperature rises
  2. It always grows
  3. It disappears at low temperature
  4. It is unaffected
Show answer & solution

Answer: (A) The two-phase region usually shrinks as temperature rises

Mutual solubility generally increases with temperature.

Question 23

What is a rotating disc contactor (RDC)?

  1. A membrane module
  2. An agitated extraction column with discs on a central shaft to disperse one phase
  3. A distillation tray
  4. A dryer
Show answer & solution

Answer: (B) An agitated extraction column with discs on a central shaft to disperse one phase

Stators between discs limit back-mixing.

Question 24

What is a Podbielniak extractor?

  1. A crystalliser
  2. A tray dryer
  3. A crusher
  4. A centrifugal extractor giving rapid countercurrent contact with short residence time
Show answer & solution

Answer: (D) A centrifugal extractor giving rapid countercurrent contact with short residence time

It is used for antibiotics such as penicillin.

Question 25

What is the role of density difference between phases in extraction?

  1. It prevents extraction
  2. It has no role
  3. It allows the phases to separate by gravity or centrifugal force
  4. It increases solubility
Show answer & solution

Answer: (C) It allows the phases to separate by gravity or centrifugal force

Small density differences need centrifugal separators.

Question 26

How many ideal stages are needed if a single-stage extraction leaves the required raffinate composition?

  1. Infinite
  2. One
  3. Two
  4. Zero
Show answer & solution

Answer: (B) One

Each ideal stage gives equilibrium extract and raffinate.

Practice these 26 questions interactively →