What are the main laws used to estimate energy for size reduction?
Show answer & solution
Answer: (D) Rittinger's, Kick's and Bond's laws
Each applies best to a different size range.
Chemical Engineering · Fluid Mechanics & Mechanical Operations
24 questions, each with the answer and a worked solution.
Practice interactively and track your score →What are the main laws used to estimate energy for size reduction?
Answer: (D) Rittinger's, Kick's and Bond's laws
Each applies best to a different size range.
What does Rittinger's law state?
Answer: (A) The energy required is proportional to the new surface area created
It applies best to fine grinding.
What does Kick's law state?
Answer: (C) The energy required is proportional to the logarithm of the size reduction ratio
It applies best to coarse crushing.
What does Bond's law state?
Answer: (B) The work required is proportional to (1/√Dp − 1/√Df)
Bond's work index is found from standard tests.
What is the Bond work index?
Answer: (C) The energy in kWh per tonne needed to reduce material from very large size to 80% passing 100 μm
It is used to size crushers and mills.
Which crusher is commonly used for primary crushing of hard rocks such as limestone?
Answer: (B) Jaw crusher
Gyratory crushers are used for very large capacities.
Which machine is commonly used for fine grinding in cement plants?
Answer: (A) Ball mill (or vertical roller mill)
Cement clinker and raw meal are ground in such mills.
What is the critical speed of a ball mill?
Answer: (D) The speed at which balls just start to centrifuge and stay against the shell
Nc = (1/2π)√(g/(R − r)).
At what fraction of the critical speed are ball mills usually operated?
Answer: (B) About 65 to 80%
At critical speed there is no grinding action.
What is the reduction ratio of a crusher?
Answer: (D) The ratio of feed size to product size
Jaw crushers typically give 4:1 to 9:1.
Which size reduction machine works mainly by impact?
Answer: (A) Hammer mill
Hammers swing at high speed and shatter the feed.
Which mill uses high-velocity jets of air or steam to grind particles by collision?
Answer: (C) Fluid energy (jet) mill
It produces very fine powders.
What is closed-circuit grinding?
Answer: (C) Grinding in which oversize product is separated and returned to the mill
It saves energy and avoids over-grinding.
What does mesh number of a screen mean?
Answer: (D) The number of openings per linear inch
Higher mesh numbers mean finer openings.
Which screen series has openings increasing in the ratio √2 between successive screens?
Answer: (A) Tyler standard screen series
The base screen is 200 mesh with 74 μm openings.
What is the opening size of a 200 mesh Tyler screen?
Answer: (D) About 74 μm
It is a common reference for fine powders.
What is screen effectiveness?
Answer: (B) A measure combining recovery of desired material and rejection of undesired material
It is the product of the recovery fractions in overflow and underflow.
What is the material that passes through a screen called?
Answer: (C) Undersize (fines or underflow)
Material retained on the screen is the oversize.
What is sphericity of a particle?
Answer: (A) The ratio of the surface area of a sphere of the same volume to the actual surface area of the particle
It equals 1 for a sphere and is less for other shapes.
What is the Sauter mean diameter?
Answer: (B) The diameter of a particle with the same volume-to-surface ratio as the whole sample
It is useful for mass transfer and reaction calculations.
Which equipment is used for coarse screening of large lumps?
Answer: (B) Grizzly
A grizzly is a set of parallel bars.
What is the function of a vibrating screen?
Answer: (A) To separate particles by size using vibration to move material over the screen
It has high capacity and resists blinding.
Which crusher is suited to friable materials such as coal and uses rotating cylinders?
Answer: (C) Roll crusher
Smooth or toothed rolls nip and crush the feed.
What is the product of a crusher compared with the product of a grinder?
Answer: (C) Crushers give coarse products while grinders give fine powders
Crushing is followed by grinding in ore and cement plants.