Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Fluid Mechanics & Mechanical Operations: Fluid Properties and Statics

Chemical Engineering · Fluid Mechanics & Mechanical Operations

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What distinguishes a fluid from a solid?

  1. A fluid always has zero viscosity
  2. A fluid has no mass
  3. A fluid cannot be compressed at all
  4. A fluid deforms continuously under any shear stress, however small
Show answer & solution

Answer: (D) A fluid deforms continuously under any shear stress, however small

Solids resist shear by static deformation.

Question 2

What is a Newtonian fluid?

  1. A fluid that needs a yield stress to flow
  2. A fluid in which shear stress is directly proportional to the rate of shear strain
  3. A fluid whose viscosity increases with shear rate
  4. A fluid with zero viscosity
Show answer & solution

Answer: (B) A fluid in which shear stress is directly proportional to the rate of shear strain

Water, air and most gases are Newtonian.

Question 3

What does Newton's law of viscosity state?

  1. Pressure equals density times gravity times depth
  2. Force equals mass times acceleration
  3. Shear stress equals viscosity multiplied by the velocity gradient
  4. Flow rate equals area times velocity
Show answer & solution

Answer: (C) Shear stress equals viscosity multiplied by the velocity gradient

τ = μ (du/dy).

Question 4

What is an ideal fluid?

  1. A hypothetical fluid that is incompressible and has zero viscosity
  2. A fluid that is compressible but frictionless only
  3. A fluid with very high viscosity
  4. A Newtonian fluid at high temperature
Show answer & solution

Answer: (A) A hypothetical fluid that is incompressible and has zero viscosity

It is used to simplify flow analysis.

Question 5

How does the viscosity of a liquid change as temperature rises?

  1. It increases
  2. It becomes infinite
  3. It decreases
  4. It stays constant
Show answer & solution

Answer: (C) It decreases

Cohesive forces weaken as temperature rises.

Question 6

How does the viscosity of a gas change as temperature rises?

  1. It stays constant
  2. It increases
  3. It decreases
  4. It becomes zero
Show answer & solution

Answer: (B) It increases

Momentum transfer by molecular motion increases.

Question 7

What is a pseudoplastic (shear-thinning) fluid?

  1. A fluid whose apparent viscosity decreases as shear rate increases
  2. A fluid that needs a yield stress
  3. A fluid with constant viscosity
  4. A fluid whose apparent viscosity increases with shear rate
Show answer & solution

Answer: (A) A fluid whose apparent viscosity decreases as shear rate increases

Polymer solutions, paints and blood are examples.

Question 8

What is a dilatant (shear-thickening) fluid?

  1. A fluid whose viscosity decreases with shear rate
  2. A fluid with zero viscosity
  3. A Newtonian fluid
  4. A fluid whose apparent viscosity increases as shear rate increases
Show answer & solution

Answer: (D) A fluid whose apparent viscosity increases as shear rate increases

Concentrated starch suspensions behave this way.

Question 9

What is a Bingham plastic?

  1. A gas at low pressure
  2. A material that behaves as a solid until a yield stress is exceeded and then flows like a Newtonian fluid
  3. An ideal fluid
  4. A shear-thickening fluid with no yield stress
Show answer & solution

Answer: (B) A material that behaves as a solid until a yield stress is exceeded and then flows like a Newtonian fluid

Toothpaste and drilling mud are approximate examples.

Question 10

What is a thixotropic fluid?

  1. A fluid whose apparent viscosity decreases with time under constant shear
  2. An ideal gas
  3. A fluid whose viscosity increases with time under shear
  4. A fluid with constant viscosity over time
Show answer & solution

Answer: (A) A fluid whose apparent viscosity decreases with time under constant shear

Some paints and gels are thixotropic.

Question 11

What is the power-law (Ostwald–de Waele) model for non-Newtonian fluids?

  1. τ = τ₀ only
  2. τ = μ(du/dy) only
  3. τ = K(du/dy)ⁿ, with n < 1 for shear-thinning and n > 1 for shear-thickening fluids
  4. P = ρgh
Show answer & solution

Answer: (C) τ = K(du/dy)ⁿ, with n < 1 for shear-thinning and n > 1 for shear-thickening fluids

n = 1 gives a Newtonian fluid.

Question 12

What is kinematic viscosity?

  1. The velocity gradient
  2. The ratio of density to viscosity
  3. The product of viscosity and density
  4. The ratio of dynamic viscosity to density
Show answer & solution

Answer: (D) The ratio of dynamic viscosity to density

Its SI unit is m²/s.

Question 13

What is the SI unit of dynamic viscosity?

  1. m²/s
  2. Pa·s (N·s/m²)
  3. kg/m³
  4. N/m
Show answer & solution

Answer: (B) Pa·s (N·s/m²)

1 Pa·s = 10 poise = 1,000 cP.

Question 14

What causes surface tension?

  1. Gravity alone
  2. Compressibility
  3. Viscosity
  4. Unbalanced cohesive forces on molecules at a liquid surface
Show answer & solution

Answer: (D) Unbalanced cohesive forces on molecules at a liquid surface

Its unit is N/m.

Question 15

What is the approximate surface tension of water at room temperature?

  1. About 0.0072 N/m
  2. About 0.072 N/m
  3. About 7.2 N/m
  4. About 72 N/m
Show answer & solution

Answer: (B) About 0.072 N/m

Surface tension falls as temperature rises.

Question 16

Why does water rise in a clean glass capillary tube while mercury is depressed?

  1. Mercury is lighter than water
  2. Water has lower density than air
  3. Water wets glass (adhesion exceeds cohesion), while mercury does not
  4. Glass repels water
Show answer & solution

Answer: (C) Water wets glass (adhesion exceeds cohesion), while mercury does not

Capillary rise h = 4σ cos θ/(ρgd).

Question 17

How does capillary rise depend on tube diameter?

  1. It is inversely proportional to the diameter
  2. It is directly proportional to diameter
  3. It is independent of diameter
  4. It is proportional to diameter squared
Show answer & solution

Answer: (A) It is inversely proportional to the diameter

Narrower tubes give greater rise.

Question 18

What is the bulk modulus of a fluid?

  1. The ratio of density to pressure
  2. The ratio of shear stress to shear strain
  3. The surface tension per unit length
  4. The ratio of pressure increase to the resulting fractional decrease in volume
Show answer & solution

Answer: (D) The ratio of pressure increase to the resulting fractional decrease in volume

Its reciprocal is compressibility.

Question 19

What is the pressure at a depth of 10 m in fresh water above atmospheric pressure?

  1. About 1 kPa
  2. About 9.8 kPa
  3. About 98 kPa
  4. About 980 kPa
Show answer & solution

Answer: (C) About 98 kPa

P = ρgh = 1,000 × 9.81 × 10.

Question 20

What does Pascal's law state?

  1. Pressure applied to a confined fluid is transmitted equally in all directions
  2. Pressure falls with depth
  3. Pressure depends on the shape of the vessel
  4. Fluids cannot transmit pressure
Show answer & solution

Answer: (A) Pressure applied to a confined fluid is transmitted equally in all directions

Hydraulic presses and jacks work on this principle.

Question 21

Why does pressure at the bottom of vessels of different shapes but the same liquid depth come out equal?

  1. Air pressure is different
  2. The vessels contain the same volume
  3. The vessels have the same base area
  4. Hydrostatic pressure depends only on depth, density and gravity
Show answer & solution

Answer: (D) Hydrostatic pressure depends only on depth, density and gravity

This is the hydrostatic paradox.

Question 22

What does a simple U-tube manometer measure?

  1. Surface tension
  2. Flow velocity directly
  3. Pressure difference using the height difference of a liquid column
  4. Viscosity
Show answer & solution

Answer: (C) Pressure difference using the height difference of a liquid column

ΔP = (ρm − ρ)gh for a manometer in a flowing line.

Question 23

Which manometer is used to measure very small pressure differences?

  1. Inclined tube manometer
  2. Bourdon gauge
  3. Piezometer only
  4. Simple U-tube with mercury
Show answer & solution

Answer: (A) Inclined tube manometer

Inclining the tube magnifies the reading along its length.

Question 24

Which instrument is the most common mechanical pressure gauge in process plants?

  1. Inclined manometer
  2. Bourdon tube gauge
  3. Hydrometer
  4. Rotameter
Show answer & solution

Answer: (B) Bourdon tube gauge

A curved tube straightens as internal pressure rises.

Question 25

What does Archimedes' principle state?

  1. Buoyancy depends on the body's colour
  2. A body sinks if its volume is large
  3. A body immersed in a fluid experiences an upward force equal to the weight of fluid displaced
  4. Pressure is equal in all directions
Show answer & solution

Answer: (C) A body immersed in a fluid experiences an upward force equal to the weight of fluid displaced

The upward force is called buoyancy.

Question 26

When is a floating body in stable equilibrium?

  1. When its metacentre lies above its centre of gravity
  2. When its centre of gravity is above the metacentre
  3. When its centre of buoyancy is at the surface
  4. When it is fully submerged only
Show answer & solution

Answer: (A) When its metacentre lies above its centre of gravity

Metacentric height GM must be positive.

Question 27

Where does the total hydrostatic force on a vertical submerged plane surface act?

  1. At the centroid exactly
  2. At the centre of pressure, which lies below the centroid
  3. At the free surface
  4. At the top edge
Show answer & solution

Answer: (B) At the centre of pressure, which lies below the centroid

The centre of pressure approaches the centroid as depth increases.

Question 28

What is the hydrostatic force on one side of a vertical gate 2 m wide holding water 3 m deep?

  1. About 29 kN
  2. About 59 kN
  3. About 88 kN
  4. About 176 kN
Show answer & solution

Answer: (C) About 88 kN

F = ρg (h/2)(A) = 1,000 × 9.81 × 1.5 × 6.

Question 29

Which liquid is most commonly used in barometers?

  1. Glycerine
  2. Water
  3. Alcohol
  4. Mercury
Show answer & solution

Answer: (D) Mercury

Its high density keeps the column short (760 mm).

Question 30

What is vapour pressure in the context of fluid machinery?

  1. The atmospheric pressure
  2. The gauge pressure in a pipe
  3. The pressure drop across a valve
  4. The pressure at which a liquid boils at a given temperature
Show answer & solution

Answer: (D) The pressure at which a liquid boils at a given temperature

Local pressure below vapour pressure causes cavitation.

Practice these 30 questions interactively →