What is steady flow?
Show answer & solution
Answer: (A) Flow in which conditions at any point do not change with time
Uniform flow means no change with position.
Chemical Engineering · Fluid Mechanics & Mechanical Operations
26 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is steady flow?
Answer: (A) Flow in which conditions at any point do not change with time
Uniform flow means no change with position.
What is uniform flow?
Answer: (B) Flow in which the velocity does not change with position along the flow at a given instant
Flow in a long straight pipe of constant diameter is uniform.
What is a streamline?
Answer: (B) A line that is everywhere tangent to the velocity vector at an instant
In steady flow, streamlines, pathlines and streaklines coincide.
What does the continuity equation for incompressible flow state?
Answer: (C) A₁V₁ = A₂V₂
It expresses conservation of mass.
If water flows through a pipe that narrows from 200 mm to 100 mm diameter, how does the velocity change?
Answer: (A) It increases four times
Velocity is inversely proportional to area, which varies with diameter squared.
What is the volumetric flow rate of water flowing at 2 m/s in a pipe of 0.1 m² cross-section?
Answer: (B) 0.2 m³/s
Q = AV.
What does Bernoulli's equation express for ideal steady flow along a streamline?
Answer: (D) The sum of pressure head, velocity head and elevation head is constant
P/ρg + V²/2g + z = constant.
What are the assumptions behind Bernoulli's equation?
Answer: (C) Steady, incompressible, frictionless flow along a streamline
Losses and work terms are added in the extended energy equation.
What is the velocity head of water flowing at 4.43 m/s?
Answer: (B) About 1 m
V²/2g = 19.6/19.62.
What is the theoretical velocity of a jet issuing from an orifice under a head H according to Torricelli's theorem?
Answer: (D) √(2gH)
Actual velocity is lower by the coefficient of velocity.
What is the theoretical velocity of water from an orifice 5 m below the free surface?
Answer: (C) About 9.9 m/s
V = √(2 × 9.81 × 5).
What is the Reynolds number?
Answer: (A) The ratio of inertial forces to viscous forces
Re = ρVD/μ.
Below what Reynolds number is flow in a circular pipe usually laminar?
Answer: (B) About 2,100
Above about 4,000 flow is usually turbulent.
What is the Reynolds number of water (ν = 1 × 10⁻⁶ m²/s) flowing at 1 m/s in a 50 mm pipe?
Answer: (C) 50,000
Re = VD/ν = 1 × 0.05/10⁻⁶.
Which dimensionless number is the ratio of inertial forces to gravity forces?
Answer: (A) Froude number
It governs open-channel flow and ship models.
Which dimensionless number is the ratio of flow velocity to the speed of sound?
Answer: (D) Mach number
Compressibility matters above about Mach 0.3.
Which dimensionless number involves surface tension?
Answer: (A) Weber number
It is used in droplet and spray analysis.
Which theorem is used to form dimensionless groups from a set of physical variables?
Answer: (D) Buckingham π theorem
n variables with m fundamental dimensions give n − m groups.
What is the boundary layer?
Answer: (A) A thin region near a solid surface where velocity changes from zero to the free-stream value
The no-slip condition creates the boundary layer.
What is the no-slip condition?
Answer: (B) Fluid in contact with a solid surface has the same velocity as the surface
It is the basis of boundary-layer theory.
What causes boundary-layer separation?
Answer: (C) An adverse pressure gradient that slows the near-wall fluid until it reverses
Separation creates wakes and form drag.
What does the momentum equation applied to a control volume give?
Answer: (D) The net force on the fluid equals the rate of change of momentum flux
It is used to find forces on bends and jets.
What is the force exerted by a water jet of mass flow 10 kg/s at 20 m/s striking a fixed flat plate normally?
Answer: (C) 200 N
F = ṁV.
What is a stagnation point?
Answer: (A) A point in a flow field where the local velocity is zero
Pressure is maximum at the stagnation point.
What is the drag coefficient used for?
Answer: (B) To relate drag force to dynamic pressure and reference area
FD = CD A ρV²/2.
What is the dynamic pressure of a fluid?
Answer: (C) ρV²/2
It is converted to pressure rise at a stagnation point.