Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Fluid Mechanics & Mechanical Operations: Pumps and Compressors

Chemical Engineering · Fluid Mechanics & Mechanical Operations

29 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which pump type is most widely used in chemical process plants?

  1. Diaphragm pump
  2. Reciprocating pump
  3. Centrifugal pump
  4. Gear pump
Show answer & solution

Answer: (C) Centrifugal pump

It suits large flows of low-viscosity liquids.

Question 2

What does a centrifugal pump use to raise liquid pressure?

  1. A flexible diaphragm
  2. A rotating impeller that imparts kinetic energy, converted to pressure in the casing
  3. A reciprocating piston
  4. Meshing gears
Show answer & solution

Answer: (B) A rotating impeller that imparts kinetic energy, converted to pressure in the casing

The volute or diffuser converts velocity to pressure.

Question 3

Why must a centrifugal pump be primed before starting?

  1. It would overheat the motor
  2. It would run backwards
  3. It needs oil lubrication
  4. It cannot generate enough suction to lift liquid when filled with air
Show answer & solution

Answer: (D) It cannot generate enough suction to lift liquid when filled with air

Self-priming designs keep liquid in the casing.

Question 4

What is cavitation in a pump?

  1. Formation and collapse of vapour bubbles where local pressure falls below vapour pressure
  2. Leakage at the seal
  3. Overheating of the motor
  4. Air entry at the discharge
Show answer & solution

Answer: (A) Formation and collapse of vapour bubbles where local pressure falls below vapour pressure

It causes noise, vibration and pitting of the impeller.

Question 5

What does NPSH stand for?

  1. Net positive suction head
  2. Net pressure supply height
  3. Nominal pump speed head
  4. Normal pump static head
Show answer & solution

Answer: (A) Net positive suction head

NPSH available must exceed NPSH required to avoid cavitation.

Question 6

How can NPSH available to a pump be increased?

  1. By heating the liquid
  2. By increasing suction pipe length
  3. By throttling the suction valve
  4. By raising the liquid level above the pump or reducing suction line losses
Show answer & solution

Answer: (D) By raising the liquid level above the pump or reducing suction line losses

Cooler liquid also has lower vapour pressure.

Question 7

According to the affinity laws, how does a centrifugal pump's flow rate change with speed?

  1. In proportion to speed squared
  2. In proportion to speed
  3. Independently of speed
  4. In proportion to speed cubed
Show answer & solution

Answer: (B) In proportion to speed

Head varies with N² and power with N³.

Question 8

According to the affinity laws, how does power change if pump speed doubles?

  1. It stays the same
  2. It increases 4 times
  3. It increases 8 times
  4. It doubles
Show answer & solution

Answer: (C) It increases 8 times

P is proportional to N³.

Question 9

How does the head developed by a centrifugal pump change if speed doubles?

  1. It halves
  2. It doubles
  3. It increases 8 times
  4. It increases 4 times
Show answer & solution

Answer: (D) It increases 4 times

H is proportional to N².

Question 10

Where is the operating point of a centrifugal pump in a system?

  1. At zero flow
  2. At the maximum head
  3. At the intersection of the pump head–flow curve and the system curve
  4. At the maximum power
Show answer & solution

Answer: (C) At the intersection of the pump head–flow curve and the system curve

It should be near the best efficiency point.

Question 11

How are two identical centrifugal pumps arranged to increase flow at the same head?

  1. In series
  2. In parallel
  3. One upstream of the tank only
  4. With one running backwards
Show answer & solution

Answer: (B) In parallel

Pumps in series increase head at the same flow.

Question 12

Why is a centrifugal pump usually started with the discharge valve closed?

  1. Power demand is lowest at zero flow, reducing motor starting load
  2. Head is zero at shutoff
  3. To prevent priming
  4. To increase cavitation
Show answer & solution

Answer: (A) Power demand is lowest at zero flow, reducing motor starting load

It must not run long against a closed valve, or it overheats.

Question 13

What is the hydraulic power required to pump 0.01 m³/s of water against a head of 50 m?

  1. About 0.49 kW
  2. About 0.5 kW
  3. About 4.9 kW
  4. About 49 kW
Show answer & solution

Answer: (C) About 4.9 kW

P = ρgQH = 1,000 × 9.81 × 0.01 × 50.

Question 14

What is the shaft power needed if the hydraulic power is 4.9 kW and pump efficiency is 70%?

  1. 3.4 kW
  2. 4.9 kW
  3. 7 kW
  4. 10 kW
Show answer & solution

Answer: (C) 7 kW

Shaft power = 4.9/0.7.

Question 15

Which pump type is preferred for metering accurate small flows of chemicals?

  1. Jet pump
  2. Large centrifugal pump
  3. Air-lift pump
  4. Reciprocating plunger or diaphragm metering pump
Show answer & solution

Answer: (D) Reciprocating plunger or diaphragm metering pump

Stroke length adjustment sets the flow.

Question 16

Why is an air vessel fitted to a reciprocating pump?

  1. To smooth the pulsating flow and reduce acceleration head
  2. To increase cavitation
  3. To prime the pump
  4. To cool the motor
Show answer & solution

Answer: (A) To smooth the pulsating flow and reduce acceleration head

It also saves power against friction.

Question 17

Which pump type is suitable for highly viscous liquids such as molasses?

  1. Air-lift pump
  2. Positive displacement pump such as a gear or screw pump
  3. Centrifugal pump with open impeller only
  4. Jet pump
Show answer & solution

Answer: (B) Positive displacement pump such as a gear or screw pump

Centrifugal efficiency falls sharply with viscosity.

Question 18

What safety device must be fitted on the discharge of a positive displacement pump?

  1. A pressure relief valve
  2. A check valve on suction only
  3. A foot valve
  4. A strainer only
Show answer & solution

Answer: (A) A pressure relief valve

Pressure rises without limit against a closed valve.

Question 19

What is the specific speed of a pump used for?

  1. To measure viscosity
  2. To classify impeller type and compare geometrically similar pumps
  3. To find the motor speed
  4. To find the pipe size
Show answer & solution

Answer: (B) To classify impeller type and compare geometrically similar pumps

Low values suit radial impellers and high values axial ones.

Question 20

What is the function of a foot valve in a pump suction line?

  1. To measure flow
  2. To cool the pump
  3. To control discharge pressure
  4. To keep the suction line full of liquid when the pump stops
Show answer & solution

Answer: (D) To keep the suction line full of liquid when the pump stops

It usually includes a strainer.

Question 21

What does a compressor's compression ratio mean?

  1. The ratio of absolute discharge pressure to absolute suction pressure
  2. The ratio of volumes at inlet only
  3. The ratio of speeds
  4. The ratio of gauge pressures
Show answer & solution

Answer: (A) The ratio of absolute discharge pressure to absolute suction pressure

High ratios use multistage compression with intercooling.

Question 22

Why is intercooling used in multistage compressors?

  1. It raises the discharge temperature
  2. It removes the need for lubrication
  3. It reduces the work of compression and the discharge temperature
  4. It increases the work required
Show answer & solution

Answer: (C) It reduces the work of compression and the discharge temperature

Ideal intercooling cools gas back to the inlet temperature.

Question 23

What is the optimum pressure ratio per stage for a two-stage compressor from P₁ to P₃?

  1. (P₃/P₁)/2
  2. P₃/P₁
  3. (P₃ − P₁)/2
  4. √(P₃/P₁)
Show answer & solution

Answer: (D) √(P₃/P₁)

Equal pressure ratios minimise total work.

Question 24

Which compression process requires the minimum work?

  1. Adiabatic compression
  2. Isothermal compression
  3. Polytropic compression with n > γ
  4. Isochoric compression
Show answer & solution

Answer: (B) Isothermal compression

In practice adiabatic compression is closer to reality.

Question 25

Which machine is used for high gas flows at low pressure rise, such as in cooling towers and furnaces?

  1. Fan
  2. Gear pump
  3. Vacuum ejector
  4. Reciprocating compressor
Show answer & solution

Answer: (A) Fan

Blowers give moderate and compressors high pressure ratios.

Question 26

Which device creates vacuum by passing high-velocity steam through a nozzle?

  1. Gear pump
  2. Steam jet ejector
  3. Centrifuge
  4. Rotameter
Show answer & solution

Answer: (B) Steam jet ejector

It has no moving parts and is used in vacuum distillation.

Question 27

What is the clearance volume effect in a reciprocating compressor?

  1. It increases capacity
  2. It eliminates heat of compression
  3. Gas left in the clearance re-expands and reduces volumetric efficiency
  4. It removes the need for valves
Show answer & solution

Answer: (C) Gas left in the clearance re-expands and reduces volumetric efficiency

Volumetric efficiency falls as pressure ratio rises.

Question 28

What is a peristaltic pump?

  1. A screw compressor
  2. A centrifugal pump with two impellers
  3. A jet pump
  4. A pump that moves fluid by squeezing a flexible tube with rollers
Show answer & solution

Answer: (D) A pump that moves fluid by squeezing a flexible tube with rollers

The fluid touches only the tube, so it suits sterile or corrosive service.

Question 29

What is the shutoff head of a centrifugal pump?

  1. The head developed at zero flow
  2. The friction head
  3. The suction head
  4. The head at maximum flow
Show answer & solution

Answer: (A) The head developed at zero flow

It is the highest point on the H–Q curve for most pumps.

Practice these 29 questions interactively →