Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Fluid Mechanics & Mechanical Operations: Flow in Pipes

Chemical Engineering · Fluid Mechanics & Mechanical Operations

29 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the velocity distribution for fully developed laminar flow in a circular pipe?

  1. Logarithmic only
  2. Linear from the wall
  3. Uniform across the section
  4. Parabolic, with maximum velocity at the centre
Show answer & solution

Answer: (D) Parabolic, with maximum velocity at the centre

This is Hagen–Poiseuille flow.

Question 2

What is the ratio of maximum velocity to average velocity for laminar flow in a circular pipe?

  1. 1
  2. 1.22
  3. 1.5
  4. 2
Show answer & solution

Answer: (D) 2

The average velocity is half the centreline velocity.

Question 3

What is the ratio of average velocity to maximum velocity for fully developed turbulent flow in a pipe, approximately?

  1. About 0.3
  2. About 0.5
  3. About 0.8
  4. About 1.0
Show answer & solution

Answer: (C) About 0.8

Turbulent profiles are flatter than laminar profiles.

Question 4

What does the Hagen–Poiseuille equation give for laminar pipe flow?

  1. Pressure drop independent of length
  2. Pressure drop proportional to viscosity, length and flow rate and inversely proportional to D⁴
  3. Pressure drop proportional to velocity squared
  4. Flow independent of viscosity
Show answer & solution

Answer: (B) Pressure drop proportional to viscosity, length and flow rate and inversely proportional to D⁴

ΔP = 128μLQ/(πD⁴).

Question 5

In laminar flow through a pipe at the same flow rate, how does the pressure drop change if the diameter is halved?

  1. It increases 16 times
  2. It increases 32 times
  3. It doubles
  4. It increases 4 times
Show answer & solution

Answer: (A) It increases 16 times

ΔP is proportional to 1/D⁴ at constant Q.

Question 6

What is the Darcy friction factor for laminar flow in a circular pipe?

  1. 0.0055
  2. 0.316/Re^0.25
  3. 16/Re
  4. 64/Re
Show answer & solution

Answer: (D) 64/Re

The Fanning friction factor is 16/Re.

Question 7

How is the Darcy friction factor related to the Fanning friction factor?

  1. The Darcy factor is half the Fanning factor
  2. They are equal
  3. The Darcy factor is four times the Fanning factor
  4. The Fanning factor is four times the Darcy factor
Show answer & solution

Answer: (C) The Darcy factor is four times the Fanning factor

Always check which factor a chart uses.

Question 8

What does the Darcy–Weisbach equation give?

  1. Head loss due to friction, hf = f(L/D)(V²/2g)
  2. Pump power
  3. Flow through an orifice
  4. Pressure at depth
Show answer & solution

Answer: (A) Head loss due to friction, hf = f(L/D)(V²/2g)

It applies to both laminar and turbulent flow.

Question 9

Which chart gives the friction factor as a function of Reynolds number and relative roughness?

  1. Psychrometric chart
  2. Moody chart
  3. Cox chart
  4. Mollier chart
Show answer & solution

Answer: (B) Moody chart

It is based on the Colebrook equation.

Question 10

In fully rough turbulent flow, what does the friction factor depend on?

  1. Pipe length
  2. Reynolds number only
  3. Relative roughness only
  4. Fluid density only
Show answer & solution

Answer: (C) Relative roughness only

It becomes independent of Re.

Question 11

Which correlation gives the friction factor for turbulent flow in smooth pipes for Re up to about 10⁵?

  1. Hagen–Poiseuille equation
  2. Ergun equation
  3. Stokes' law
  4. Blasius equation, f = 0.316/Re^0.25
Show answer & solution

Answer: (D) Blasius equation, f = 0.316/Re^0.25

It gives the Darcy friction factor.

Question 12

What are minor losses in piping systems?

  1. Head losses at fittings, valves, bends, entrances, exits and changes in section
  2. Losses in long straight pipes only
  3. Losses in pumps only
  4. Losses due to elevation
Show answer & solution

Answer: (A) Head losses at fittings, valves, bends, entrances, exits and changes in section

They are expressed as K(V²/2g) or equivalent length.

Question 13

What is the loss coefficient for a sudden exit of a pipe into a large tank?

  1. 0.05
  2. 0.5
  3. 1.0
  4. 2.0
Show answer & solution

Answer: (C) 1.0

All velocity head is lost.

Question 14

What is the loss coefficient for a sharp-edged entrance from a tank into a pipe, approximately?

  1. 0.04
  2. 0.5
  3. 1.0
  4. 5.0
Show answer & solution

Answer: (B) 0.5

Rounded entrances have much lower losses.

Question 15

What is the head loss due to a sudden enlargement (Borda–Carnot)?

  1. (V₁ + V₂)²/2g
  2. Zero
  3. V₁²/2g
  4. (V₁ − V₂)²/2g
Show answer & solution

Answer: (D) (V₁ − V₂)²/2g

V₁ and V₂ are the upstream and downstream velocities.

Question 16

What is the equivalent length of a fitting?

  1. The length of straight pipe that would give the same head loss as the fitting
  2. The physical length of the fitting
  3. The length of the system
  4. The pipe diameter
Show answer & solution

Answer: (A) The length of straight pipe that would give the same head loss as the fitting

It is often expressed as L/D.

Question 17

What is the hydraulic diameter of a non-circular duct?

  1. The diagonal of the duct
  2. Four times the cross-sectional area divided by the wetted perimeter
  3. Twice the perimeter
  4. The width of the duct
Show answer & solution

Answer: (B) Four times the cross-sectional area divided by the wetted perimeter

For a circular pipe it equals the diameter.

Question 18

What is the hydraulic diameter of a square duct of side a?

  1. 2a
  2. a
  3. a/2
  4. 4a
Show answer & solution

Answer: (B) a

4a²/(4a) = a.

Question 19

How does the total flow divide among pipes in parallel?

  1. Each branch carries equal flow
  2. Velocities add
  3. Head losses add
  4. Each branch has the same head loss, and flows add up to the total
Show answer & solution

Answer: (D) Each branch has the same head loss, and flows add up to the total

For pipes in series, flow is the same and losses add.

Question 20

For turbulent flow at a fixed friction factor, how does head loss vary with velocity?

  1. In proportion to velocity
  2. In proportion to the square root of velocity
  3. In proportion to velocity squared
  4. Independently of velocity
Show answer & solution

Answer: (C) In proportion to velocity squared

Doubling velocity multiplies loss by four.

Question 21

What is water hammer?

  1. A pressure surge in a pipeline caused by sudden closure of a valve
  2. A pump failure due to cavitation
  3. A flow meter
  4. A type of pipe joint
Show answer & solution

Answer: (A) A pressure surge in a pipeline caused by sudden closure of a valve

Slow valve closure and surge tanks reduce it.

Question 22

What is the economic pipe diameter?

  1. The smallest available diameter
  2. The diameter giving laminar flow
  3. The largest diameter
  4. The diameter that minimises the total of pipe capital cost and pumping energy cost
Show answer & solution

Answer: (D) The diameter that minimises the total of pipe capital cost and pumping energy cost

Typical water velocities are 1–3 m/s.

Question 23

What is a typical economic velocity for water in process pipelines?

  1. About 0.01 m/s
  2. About 1 to 3 m/s
  3. About 20 to 30 m/s
  4. About 100 m/s
Show answer & solution

Answer: (B) About 1 to 3 m/s

Gas velocities are much higher, about 10–30 m/s.

Question 24

What is the entrance length for laminar flow in a pipe approximately?

  1. Zero
  2. About 100 Re D
  3. About 0.06 Re D
  4. About 10 D always
Show answer & solution

Answer: (C) About 0.06 Re D

Turbulent entrance lengths are about 10–60 D.

Question 25

What is the Hazen–Williams formula mainly used for?

  1. Water flow in water-supply pipelines
  2. Oil flow in laminar regime
  3. Gas flow in compressors
  4. Slurry settling
Show answer & solution

Answer: (A) Water flow in water-supply pipelines

It uses a roughness coefficient C.

Question 26

What happens to the friction head loss when pipe length doubles at the same flow?

  1. It halves
  2. It increases four times
  3. It stays the same
  4. It doubles
Show answer & solution

Answer: (D) It doubles

hf is proportional to L.

Question 27

What is the shear stress distribution in fully developed pipe flow?

  1. Uniform
  2. Linear, zero at the centre and maximum at the wall
  3. Maximum at the centre
  4. Parabolic
Show answer & solution

Answer: (B) Linear, zero at the centre and maximum at the wall

This holds for both laminar and turbulent flow.

Question 28

What is the laminar sublayer?

  1. A very thin layer next to the wall in turbulent flow where viscous effects dominate
  2. The free surface
  3. The core of turbulent flow
  4. The boundary between pipes
Show answer & solution

Answer: (A) A very thin layer next to the wall in turbulent flow where viscous effects dominate

Roughness elements that protrude through it raise friction.

Question 29

What is two-phase flow?

  1. Flow in two parallel pipes
  2. Flow of two liquids of the same phase only
  3. Simultaneous flow of two phases such as gas and liquid in a pipe
  4. Laminar and turbulent flow together
Show answer & solution

Answer: (C) Simultaneous flow of two phases such as gas and liquid in a pipe

Flow patterns include bubble, slug, annular and stratified flow.

Practice these 29 questions interactively →