Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Fluid Mechanics & Mechanical Operations: Mixing, Fluidisation and Conveying

Chemical Engineering · Fluid Mechanics & Mechanical Operations

28 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the main purpose of baffles in a mixing tank?

  1. To heat the liquid
  2. To prevent swirling and vortex formation and improve mixing
  3. To support the shaft
  4. To measure level
Show answer & solution

Answer: (B) To prevent swirling and vortex formation and improve mixing

Typically four baffles of about one-tenth of the tank diameter are used.

Question 2

Which impeller type gives mainly axial flow and is suited to solids suspension?

  1. Flat-blade Rushton turbine
  2. Anchor
  3. Propeller or pitched-blade turbine
  4. Paddle with flat blades only
Show answer & solution

Answer: (C) Propeller or pitched-blade turbine

Radial-flow turbines suit gas dispersion.

Question 3

Which impeller is used for very viscous liquids and close-wall scraping?

  1. Marine propeller
  2. Rushton turbine
  3. Fan
  4. Anchor or helical ribbon
Show answer & solution

Answer: (D) Anchor or helical ribbon

They sweep near the vessel wall.

Question 4

What is the power number in agitation?

  1. A dimensionless group P/(ρN³D⁵) relating impeller power to speed and size
  2. The motor rating
  3. The Froude number only
  4. The Reynolds number
Show answer & solution

Answer: (A) A dimensionless group P/(ρN³D⁵) relating impeller power to speed and size

In the turbulent regime it is nearly constant.

Question 5

In the turbulent regime with a baffled tank, how does agitator power vary with speed?

  1. Independently of N
  2. In proportion to N³
  3. In proportion to N
  4. In proportion to N²
Show answer & solution

Answer: (B) In proportion to N³

P = Np ρ N³ D⁵.

Question 6

How does agitator power vary with impeller diameter in the turbulent regime?

  1. In proportion to D⁵
  2. In proportion to D²
  3. In proportion to D³
  4. In proportion to D
Show answer & solution

Answer: (A) In proportion to D⁵

Small diameter changes have large power effects.

Question 7

What is the impeller Reynolds number?

  1. ρN/D
  2. ND/μ
  3. ρND²/μ
  4. ρVD/μ for pipe flow
Show answer & solution

Answer: (C) ρND²/μ

Laminar mixing occurs below about 10.

Question 8

What is the main use of a ribbon blender?

  1. Mixing low-viscosity liquids only
  2. Crushing solids
  3. Mixing gases
  4. Mixing dry powders and solids
Show answer & solution

Answer: (D) Mixing dry powders and solids

A helical ribbon moves solids in opposite directions.

Question 9

What is a kneader or sigma-blade mixer used for?

  1. Screening solids
  2. Mixing gases
  3. Pumping liquids
  4. Mixing very viscous pastes and doughs
Show answer & solution

Answer: (D) Mixing very viscous pastes and doughs

Bakery and rubber industries use them.

Question 10

What is a static mixer?

  1. A cyclone
  2. A ball mill
  3. A mixer with fixed elements in a pipe that divide and recombine the flow
  4. A rotating impeller in a tank
Show answer & solution

Answer: (C) A mixer with fixed elements in a pipe that divide and recombine the flow

It has no moving parts.

Question 11

What is minimum fluidisation velocity?

  1. The speed of sound
  2. The gas velocity at which the bed weight is just supported by the drag of the fluid
  3. The velocity at which flow stops
  4. The velocity at which particles are blown out
Show answer & solution

Answer: (B) The gas velocity at which the bed weight is just supported by the drag of the fluid

Above it the bed behaves like a fluid.

Question 12

What happens to the pressure drop across a bed once fluidisation begins?

  1. It stays approximately constant, equal to the bed weight per unit area
  2. It keeps increasing with velocity
  3. It becomes negative
  4. It drops to zero
Show answer & solution

Answer: (A) It stays approximately constant, equal to the bed weight per unit area

Further velocity increase expands the bed.

Question 13

Which equation is used to find the pressure drop through a packed bed?

  1. Ergun equation
  2. Stokes' law
  3. Bernoulli equation only
  4. Hagen–Poiseuille for a single pipe
Show answer & solution

Answer: (A) Ergun equation

It combines laminar and turbulent terms.

Question 14

Which equation gives the pressure drop for laminar flow through packed beds?

  1. Blasius equation
  2. Kozeny–Carman equation
  3. Clausius–Clapeyron equation
  4. Antoine equation
Show answer & solution

Answer: (B) Kozeny–Carman equation

It is the viscous term of the Ergun equation.

Question 15

What is bed voidage (porosity)?

  1. The bed height
  2. The particle density
  3. The particle diameter
  4. The fraction of bed volume occupied by voids between particles
Show answer & solution

Answer: (D) The fraction of bed volume occupied by voids between particles

Typical random packed beds have about 0.35–0.45 voidage.

Question 16

What is the advantage of a fluidised bed reactor?

  1. Plug flow of gas always
  2. No particle attrition
  3. Excellent heat transfer and nearly uniform temperature
  4. No need for gas
Show answer & solution

Answer: (C) Excellent heat transfer and nearly uniform temperature

Fluid catalytic cracking (FCC) uses fluidised beds.

Question 17

What is channelling in a fluidised bed?

  1. Uniform fluidisation
  2. Elutriation of fines
  3. Gas forming open paths through the bed and bypassing most particles
  4. Particles settling
Show answer & solution

Answer: (C) Gas forming open paths through the bed and bypassing most particles

It reduces gas–solid contact.

Question 18

What is slugging in a fluidised bed?

  1. Particle sintering
  2. Large gas bubbles filling the bed cross-section and lifting particle plugs
  3. Channelling at low velocity
  4. Uniform bubbling
Show answer & solution

Answer: (B) Large gas bubbles filling the bed cross-section and lifting particle plugs

It occurs in tall narrow beds.

Question 19

What is elutriation?

  1. Removal of fine particles from a bed by the upward flowing gas
  2. Grinding of particles
  3. Settling of large particles
  4. Agglomeration of particles
Show answer & solution

Answer: (A) Removal of fine particles from a bed by the upward flowing gas

Cyclones return elutriated fines.

Question 20

Which conveyor is the most common for transporting bulk solids over long distances?

  1. Vibratory feeder
  2. Screw conveyor
  3. Bucket elevator
  4. Belt conveyor
Show answer & solution

Answer: (D) Belt conveyor

Belt conveyors are used at mines and cement plants.

Question 21

Which conveyor is a rotating helix in a trough, used for short distances?

  1. Apron conveyor
  2. Belt conveyor
  3. Pneumatic conveyor
  4. Screw conveyor
Show answer & solution

Answer: (D) Screw conveyor

It also mixes material during transport.

Question 22

Which equipment lifts bulk solids vertically?

  1. Screw conveyor
  2. Bucket elevator
  3. Belt conveyor on level ground
  4. Chute
Show answer & solution

Answer: (B) Bucket elevator

It is used in cement and grain handling.

Question 23

What is pneumatic conveying?

  1. Transport of powders and granules through pipes by a gas stream
  2. Transport by gravity chutes only
  3. Transport by buckets
  4. Transport on a belt
Show answer & solution

Answer: (A) Transport of powders and granules through pipes by a gas stream

Dilute and dense phase systems are used.

Question 24

What is the angle of repose of a bulk solid?

  1. The angle of the conveyor
  2. The angle of the hopper outlet
  3. The steepest angle at which a heap of the material remains stable
  4. The angle of a cyclone cone
Show answer & solution

Answer: (C) The steepest angle at which a heap of the material remains stable

It indicates flowability.

Question 25

What is mass flow in a storage hopper?

  1. Flow through a central channel only
  2. Flow of gas only
  3. Flow in which all material in the hopper moves when any is withdrawn
  4. No flow
Show answer & solution

Answer: (C) Flow in which all material in the hopper moves when any is withdrawn

Funnel flow leaves stagnant zones.

Question 26

What is the mixing index used for in solids mixing?

  1. To measure density
  2. To measure the degree of uniformity achieved compared with a random mixture
  3. To measure particle size
  4. To measure power consumption
Show answer & solution

Answer: (B) To measure the degree of uniformity achieved compared with a random mixture

Sample variance is compared with limits.

Question 27

What is the scale-up rule for geometrically similar agitated tanks at constant power per unit volume?

  1. ND is kept constant
  2. D is kept constant
  3. N is kept constant
  4. N³D² is kept constant
Show answer & solution

Answer: (D) N³D² is kept constant

Constant tip speed means ND constant.

Question 28

What is the tip speed of an impeller?

  1. πND, the peripheral velocity of the blade tip
  2. ND²
  3. N/D
  4. ρND
Show answer & solution

Answer: (A) πND, the peripheral velocity of the blade tip

It relates to shear in the tank.

Practice these 28 questions interactively →