What is a stope?
Show answer & solution
Answer: (B) An underground excavation from which ore is extracted
Stoping is the production stage of underground metal mining.
Mining Engineering · Underground Mining Methods
37 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a stope?
Answer: (B) An underground excavation from which ore is extracted
Stoping is the production stage of underground metal mining.
What is open stoping?
Answer: (A) Mining in which stopes stay open without fill during extraction, relying on pillars and wall strength
Open stope methods include sublevel stoping and room and pillar.
Which method uses broken ore left in the stope as a working platform and draws only the swell during mining?
Answer: (C) Shrinkage stoping
Miners stand on the broken ore to drill the back.
About what proportion of the broken ore is drawn during the mining phase of shrinkage stoping?
Answer: (B) About 30 to 40%
Only the swell is drawn; the rest is drawn at the end.
Which condition is needed for shrinkage stoping?
Answer: (D) Steep dip of more than about 60° with strong ore and walls
The broken ore must flow freely and walls must stand unsupported.
Which method fills each mined slice with waste or tailings before the next slice is taken?
Answer: (C) Cut and fill stoping
The fill supports the walls and becomes the next working floor.
In which direction does overhand cut and fill mining advance?
Answer: (D) Upward in horizontal slices
Miners work on the fill and drill the back above.
How does underhand cut and fill differ from overhand cut and fill?
Answer: (A) Slices are mined downward beneath a cemented fill roof
Underhand mining is used in weak ore and rockburst-prone ground.
Which fill is a mixture of full tailings, water and cement pumped as a thick paste?
Answer: (B) Paste fill
Paste fill needs little drainage and gives good strength.
What is hydraulic fill?
Answer: (B) Deslimed tailings transported into stopes as a slurry
Excess water must drain from the stope through barricades.
What is rock fill?
Answer: (A) Waste rock placed in stopes, often with cement added
Cemented rock fill gives high strength for exposed walls.
Why is cement added to backfill?
Answer: (D) To give the fill strength so that it can stand exposed or support work beneath
Cemented fill allows adjacent stopes to be mined next to it.
Which method blasts ore from sublevel drifts into an open stope and draws it from the stope bottom?
Answer: (C) Sublevel (open) stoping
Long holes from sublevels break large tonnages into an open void.
Which drilling pattern is commonly used in long-hole open stoping?
Answer: (A) Ring (fan) drilling
Rings of holes radiate from a drift into the ore.
Which bulk stoping method uses large-diameter vertical holes blasted in horizontal slices towards an undercut?
Answer: (C) Vertical crater retreat (VCR)
Spherical charges are fired at the bottom of holes to break slices upward.
On which blasting theory is the vertical crater retreat method based?
Answer: (D) Livingston's crater theory
VCR uses crater blasting with short spherical charges.
What is a drawpoint?
Answer: (B) An opening at the stope base from which broken ore is loaded
LHDs load ore from drawpoints.
What is square set stoping?
Answer: (B) A method using timber sets in cubic frames to support weak ground in high-grade ore
Each set is a timber cube filled later with waste.
What is the main disadvantage of square set stoping?
Answer: (C) Very high timber and labour cost
It is now used only for very high-grade, weak ore.
What is stull stoping?
Answer: (D) A method for narrow veins supported by single timber stulls wedged between the walls
Stulls support walls in veins of up to about 3 m width.
What is resuing in narrow vein mining?
Answer: (A) Blasting the waste wall first and then the ore separately to reduce dilution
Resuing produces cleaner ore from very narrow veins.
What is bench and fill (Avoca) stoping?
Answer: (B) A long-hole method in which the stope is filled progressively as mining retreats
Fill placed close behind the retreating face limits open span.
Which method is generally the most selective for irregular high-grade orebodies?
Answer: (D) Cut and fill stoping
Cut and fill follows ore boundaries closely with low dilution.
What is a slot raise in long-hole stoping?
Answer: (C) A raise opened at the end of the stope to create a free face for blasting
The slot is widened into a slot before rings are fired into it.
What is the hanging wall of an inclined orebody?
Answer: (A) The rock above the orebody
Hanging wall stability controls dilution in stopes.
What is the footwall of an inclined orebody?
Answer: (A) The rock below the orebody
Footwall drives are commonly used for access.
What mainly controls the maximum stable stope wall size in open stoping?
Answer: (D) The rock mass quality of the walls and their hydraulic radius
Stable spans are estimated from classification and stability graphs.
How is the hydraulic radius of a stope surface defined?
Answer: (C) Area of the surface divided by its perimeter
Hydraulic radius is used as a shape factor in the stability graph.
Which two quantities are plotted in the Mathews stability graph for open stope design?
Answer: (B) Modified stability number N′ and hydraulic radius
The graph separates stable, transition and caving zones.
What is primary–secondary stope sequencing?
Answer: (D) Primary stopes are mined and filled with cemented fill before secondary stopes between them are mined
The cemented primary fill forms walls for the secondary stopes.
What causes most dilution in open stoping?
Answer: (A) Overbreak and sloughing from the stope walls
Wall failure adds waste to the broken ore.
What is post pillar cut and fill?
Answer: (C) Cut and fill mining in which pillars run up through the fill levels
Pillars and fill together support wide flat-dipping stopes.
Which method mines weak ore in horizontal drifts that are filled before adjacent drifts are mined?
Answer: (B) Drift and fill
Drift and fill limits open spans in poor ground.
What happens at the end of shrinkage stoping?
Answer: (C) The remaining broken ore is drawn off in a final draw
After the final draw, the stope is empty or may be filled.
What is breast stoping?
Answer: (A) A method for flat, thin deposits where ore is broken from a vertical face that advances horizontally
Breast stoping is used with pillars in flat-lying beds.
What is the main advantage of sublevel open stoping?
Answer: (A) High productivity and low cost per tonne in large, regular orebodies with strong walls
Large blasts and remote loading give high output.
Why are barricades built at drawpoints of hydraulically filled stopes?
Answer: (C) To hold the fill in place while water drains out
Barricade failure can release fill and water into the mine.