Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Underground Mining Methods: Room and Pillar

Mining Engineering · Underground Mining Methods

37 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

In which type of deposit is room and pillar mining mainly used?

  1. Loose alluvial placers
  2. Flat-lying or gently dipping bedded deposits
  3. Massive porphyry orebodies
  4. Steep narrow veins
Show answer & solution

Answer: (B) Flat-lying or gently dipping bedded deposits

Coal, salt, potash, limestone and flat lead–zinc beds suit room and pillar.

Question 2

What is the main disadvantage of room and pillar mining?

  1. It needs very steep dips
  2. It always causes surface subsidence
  3. It cannot be mechanised
  4. Ore left in pillars lowers recovery
Show answer & solution

Answer: (D) Ore left in pillars lowers recovery

Pillars can lock up 25–50% of the deposit.

Question 3

What is the typical recovery in room and pillar mining without pillar extraction?

  1. 5 to 10%
  2. 15 to 25%
  3. 50 to 75%
  4. 95 to 100%
Show answer & solution

Answer: (C) 50 to 75%

Recovery depends on depth and pillar size.

Question 4

What is a panel in room and pillar mining?

  1. A single pillar
  2. A haul road
  3. A block of rooms and pillars worked as a unit and surrounded by barrier pillars
  4. A ventilation fan
Show answer & solution

Answer: (C) A block of rooms and pillars worked as a unit and surrounded by barrier pillars

Panels allow isolation for ventilation, fire and collapse control.

Question 5

Which machine cuts and loads coal in one operation in mechanised room and pillar mining?

  1. Continuous miner
  2. Raise borer
  3. Dragline
  4. Shearer
Show answer & solution

Answer: (A) Continuous miner

The rotating cutter drum and gathering arms load coal onto its conveyor.

Question 6

Which rubber-tyred vehicle carries coal from a continuous miner to the section feeder?

  1. Armoured face conveyor
  2. Shuttle car
  3. Skip
  4. Shearer
Show answer & solution

Answer: (B) Shuttle car

Shuttle cars shuttle between the miner and the feeder-breaker.

Question 7

Which machine installs roof bolts after cutting in mechanised room and pillar mining?

  1. Scraper
  2. Shearer
  3. Scaler
  4. Roof bolter
Show answer & solution

Answer: (D) Roof bolter

Roof bolters drill and install bolts in the newly cut roof.

Question 8

What is place-change mining in room and pillar?

  1. Changing from coal to salt mining
  2. The continuous miner moves between headings so that bolting can be done in alternate places
  3. Changing shift workers
  4. Moving the mine to a new site
Show answer & solution

Answer: (B) The continuous miner moves between headings so that bolting can be done in alternate places

Place changing keeps the miner cutting while other places are bolted.

Question 9

What is the usual cycle sequence in conventional room and pillar coal mining?

  1. Undercut, drill, blast, load and support
  2. Blast, undercut, support and drill
  3. Support, load, undercut and blast
  4. Load, blast, drill and undercut
Show answer & solution

Answer: (A) Undercut, drill, blast, load and support

Conventional mining uses separate machines for each step.

Question 10

Why is the coal face undercut before blasting in conventional mining?

  1. To ventilate the face
  2. To drain water
  3. To create a free face that improves blasting
  4. To support the roof
Show answer & solution

Answer: (C) To create a free face that improves blasting

The undercut slot gives the blasted coal room to expand.

Question 11

Which variant of room and pillar leaves pillars irregularly in low-grade parts of a flat metal deposit?

  1. Sublevel caving
  2. Longwall
  3. Post pillar cut and fill
  4. Random room and pillar
Show answer & solution

Answer: (D) Random room and pillar

Pillars are placed where the ore is poorest.

Question 12

Which room and pillar variant is used in inclined orebodies, arranging rooms in steps so trackless equipment can work?

  1. Longwall
  2. Random room and pillar
  3. Step room and pillar
  4. Bord and pillar
Show answer & solution

Answer: (C) Step room and pillar

Steps keep each working floor nearly flat for LHDs and trucks.

Question 13

Up to about what dip is conventional trackless room and pillar mining practical?

  1. About 15° to 20°
  2. About 45°
  3. About 70°
  4. About 90°
Show answer & solution

Answer: (A) About 15° to 20°

Above this, rubber-tyred machines cannot work safely on the floor.

Question 14

What is retreat mining in room and pillar?

  1. Moving equipment out of the mine
  2. Driving new rooms forward
  3. Backfilling rooms
  4. Extracting pillars while working back towards the main entries
Show answer & solution

Answer: (D) Extracting pillars while working back towards the main entries

Retreat recovers coal from pillars and lets the roof cave behind.

Question 15

Why is pillar extraction carried out in retreat towards the main entries?

  1. To avoid using supports
  2. So that miners always have stable roof between them and the exit while caving occurs behind
  3. To shorten haulage
  4. To speed up ventilation
Show answer & solution

Answer: (B) So that miners always have stable roof between them and the exit while caving occurs behind

Caving is left behind the advancing extraction line.

Question 16

What is a split in bord and pillar depillaring?

  1. A roadway driven through a pillar to divide it
  2. A type of explosive
  3. A conveyor belt joint
  4. A crack in the roof
Show answer & solution

Answer: (A) A roadway driven through a pillar to divide it

Splitting reduces pillar size before final extraction.

Question 17

What is the line of extraction in depillaring?

  1. The ventilation intake
  2. The shaft centre line
  3. The main haulage road
  4. The line along which pillars are being extracted, forming the goaf boundary
Show answer & solution

Answer: (D) The line along which pillars are being extracted, forming the goaf boundary

Keeping a straight line of extraction helps regular caving.

Question 18

What is the main hazard during pillar extraction?

  1. Overheating of equipment
  2. Flooding from the surface only
  3. Roof falls and sudden caving
  4. Excess daylight
Show answer & solution

Answer: (C) Roof falls and sudden caving

Pillar recovery causes changing loads and caving close to the workers.

Question 19

What are breaker-line supports in depillaring?

  1. Supports for the shaft
  2. A row of props or chocks along the goaf edge to induce caving at that line
  3. Supports for conveyors
  4. Fence posts on the surface
Show answer & solution

Answer: (B) A row of props or chocks along the goaf edge to induce caving at that line

The breaker line controls where the roof breaks.

Question 20

Which salt mine in Pakistan is worked by room and pillar, leaving about half the salt in pillars?

  1. Saindak
  2. Duddar
  3. Khewra Salt Mine
  4. Thar Block-II
Show answer & solution

Answer: (C) Khewra Salt Mine

Khewra in the Salt Range uses about 50% extraction for stability.

Question 21

What is the main advantage of room and pillar over longwall mining?

  1. No roof support needed
  2. Better for thick, deep seams
  3. Higher recovery
  4. Lower capital cost and greater flexibility
Show answer & solution

Answer: (D) Lower capital cost and greater flexibility

Room and pillar adapts easily to irregular seams and small reserves.

Question 22

What is a multiple-entry system in room and pillar?

  1. Several parallel entries driven together for haulage and ventilation
  2. One single heading
  3. Two mines connected
  4. A shaft with two cages
Show answer & solution

Answer: (A) Several parallel entries driven together for haulage and ventilation

Multiple entries separate intake, return and haulage air.

Question 23

What is a stopping in room and pillar ventilation?

  1. A roof support
  2. A wall built across a crosscut to direct airflow
  3. A type of shaft
  4. A device that stops the conveyor
Show answer & solution

Answer: (B) A wall built across a crosscut to direct airflow

Stoppings separate intake and return airways.

Question 24

How many entries typically form a section in mechanised room and pillar coal mining?

  1. 1
  2. 3 to 8
  3. 20 to 30
  4. 50
Show answer & solution

Answer: (B) 3 to 8

Sections commonly have about five to seven entries.

Question 25

What limits the depth of cut of a continuous miner before bolting?

  1. The size of the shuttle car
  2. The ventilation fan size
  3. The colour of coal
  4. The unsupported roof distance permitted by the roof control plan
Show answer & solution

Answer: (D) The unsupported roof distance permitted by the roof control plan

Workers must not go beyond permanent support.

Question 26

Which machine loads blasted rock in trackless metal room and pillar mines?

  1. Shearer
  2. Dragline
  3. LHD (load-haul-dump)
  4. Coal plough
Show answer & solution

Answer: (C) LHD (load-haul-dump)

LHDs load, carry and dump in one machine.

Question 27

What is pillar robbing?

  1. Uncontrolled or unplanned removal of coal from pillars
  2. Planned retreat mining
  3. Backfilling pillars
  4. Building new pillars
Show answer & solution

Answer: (A) Uncontrolled or unplanned removal of coal from pillars

Robbing weakens pillars and can cause collapse.

Question 28

What does high-extraction room and pillar mining mean?

  1. Leaving very large pillars
  2. Mining with no pillars from the start
  3. Partial or full recovery of pillars after development
  4. Mining only the roof
Show answer & solution

Answer: (C) Partial or full recovery of pillars after development

High extraction raises recovery but needs strong ground control.

Question 29

Which roof condition favours room and pillar mining?

  1. Weak friable roof
  2. Swelling clay roof
  3. Water-bearing sand roof
  4. Strong competent roof
Show answer & solution

Answer: (D) Strong competent roof

Rooms must stay open for long periods with bolting only.

Question 30

What happens to room and pillar recovery as depth increases?

  1. It falls because larger pillars are needed
  2. It reaches 100%
  3. It stays constant
  4. It rises
Show answer & solution

Answer: (A) It falls because larger pillars are needed

Higher stress needs wider pillars, leaving more coal behind.

Question 31

Which deposit is typically mined by room and pillar?

  1. Kimberlite pipes
  2. Flat-lying salt beds
  3. Steep gold veins
  4. Porphyry copper bodies
Show answer & solution

Answer: (B) Flat-lying salt beds

Salt, potash and coal beds are classic room and pillar deposits.

Question 32

What is a gallery in coal mine terminology used in Pakistan's coal mine regulations?

  1. A pillar
  2. A shaft
  3. A ventilation fan
  4. A roadway driven in the seam
Show answer & solution

Answer: (D) A roadway driven in the seam

"Gallery" means any underground roadway or passage.

Question 33

What is development on the solid in bord and pillar coal mining?

  1. Mining pillars
  2. Driving galleries in unmined coal before depillaring begins
  3. Sinking a shaft
  4. Backfilling galleries
Show answer & solution

Answer: (B) Driving galleries in unmined coal before depillaring begins

Development forms the pillars that will later be extracted.

Question 34

What is the main advantage of the panel system of working?

  1. Each panel can be isolated for fire, ventilation and collapse control
  2. It avoids all roof supports
  3. It needs no ventilation
  4. It doubles extraction
Show answer & solution

Answer: (A) Each panel can be isolated for fire, ventilation and collapse control

Panels can be sealed off quickly in an emergency.

Question 35

How is coal mined in many small, non-mechanised coal mines of Pakistan?

  1. By continuous miners
  2. By longwall shearers
  3. By pick or blasting with manual loading into tubs
  4. By draglines
Show answer & solution

Answer: (C) By pick or blasting with manual loading into tubs

Most small coal mines in Balochistan and KP rely on manual methods.

Question 36

Which machine crushes and feeds coal from shuttle cars onto the section belt conveyor?

  1. Shearer
  2. Roadheader
  3. Feeder-breaker
  4. Raise borer
Show answer & solution

Answer: (C) Feeder-breaker

The feeder-breaker sizes coal and gives a steady feed to the belt.

Question 37

What is a crosscut in room and pillar mining?

  1. An opening driven at right angles between entries to form pillars
  2. A type of drill bit
  3. An inclined adit
  4. A vertical shaft
Show answer & solution

Answer: (A) An opening driven at right angles between entries to form pillars

Entries and crosscuts together outline the pillars.

Practice these 37 questions interactively →