Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Underground Mining Methods: Caving Methods

Mining Engineering · Underground Mining Methods

37 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is block caving?

  1. A room and pillar variant
  2. A surface method
  3. A method using cemented fill
  4. A mass mining method in which undercut ore caves under gravity and is drawn from drawpoints
Show answer & solution

Answer: (D) A mass mining method in which undercut ore caves under gravity and is drawn from drawpoints

Only the undercut is blasted; the rest of the ore caves naturally.

Question 2

Which orebodies are best suited to block caving?

  1. Small irregular pods
  2. Large, massive, low-grade orebodies in rock that caves well
  3. Flat thin coal seams
  4. Narrow high-grade veins
Show answer & solution

Answer: (B) Large, massive, low-grade orebodies in rock that caves well

Caving needs a large footprint and suitable fracturing.

Question 3

What is the undercut in block caving?

  1. A drawpoint
  2. A vertical shaft
  3. A ventilation raise
  4. A horizontal slot blasted beneath the block to start caving
Show answer & solution

Answer: (D) A horizontal slot blasted beneath the block to start caving

Once the undercut area is large enough, the ore above begins to cave.

Question 4

What is the extraction level in block caving?

  1. The ventilation level only
  2. The top of the ore column
  3. The level below the undercut with drawpoints for loading ore
  4. The surface
Show answer & solution

Answer: (C) The level below the undercut with drawpoints for loading ore

LHDs work on the extraction level.

Question 5

Which geometric quantity of the undercut is used to predict when caving will start?

  1. Hydraulic radius (area divided by perimeter)
  2. Undercut depth
  3. Shaft diameter
  4. Drawpoint spacing
Show answer & solution

Answer: (A) Hydraulic radius (area divided by perimeter)

Caving starts when the hydraulic radius exceeds a critical value for the rock mass.

Question 6

What is a drawbell?

  1. A bucket for shaft sinking
  2. A ventilation door
  3. A funnel-shaped opening above a drawpoint through which caved ore flows
  4. A bell used for signalling
Show answer & solution

Answer: (C) A funnel-shaped opening above a drawpoint through which caved ore flows

Drawbells connect the undercut with the extraction drawpoints.

Question 7

What is a hang-up in caving mines?

  1. A blockage of ore flow in a drawpoint or drawbell
  2. A ventilation fault
  3. A broken hoist rope
  4. A loose rock in the roof
Show answer & solution

Answer: (A) A blockage of ore flow in a drawpoint or drawbell

Large blocks arch over the drawpoint and stop flow.

Question 8

How are hang-ups and oversize at drawpoints usually dealt with?

  1. Adding water only
  2. Secondary breaking with small charges or rock breakers
  3. Increasing ventilation
  4. Closing the mine
Show answer & solution

Answer: (B) Secondary breaking with small charges or rock breakers

Secondary breaking clears the drawpoint for loading.

Question 9

What is panel caving?

  1. Surface strip caving
  2. Caving of one small block only
  3. Room and pillar with caving
  4. Block caving in which the undercut is advanced progressively across the orebody
Show answer & solution

Answer: (D) Block caving in which the undercut is advanced progressively across the orebody

Panel caving suits large flat-lying orebodies.

Question 10

What is the main advantage of block caving?

  1. High selectivity
  2. No development needed
  3. Very low cost per tonne and very high production
  4. No surface subsidence
Show answer & solution

Answer: (C) Very low cost per tonne and very high production

Block caving is the cheapest underground mining method.

Question 11

What is the main disadvantage of block caving?

  1. Low production
  2. High capital cost, long development time and surface subsidence
  3. High selectivity
  4. High operating cost
Show answer & solution

Answer: (B) High capital cost, long development time and surface subsidence

Development may take five to ten years before production.

Question 12

How does sublevel caving work?

  1. Ore is blasted in rings from sublevels while the waste above caves in and ore is drawn with some dilution
  2. Ore is mined from the surface
  3. Ore caves without blasting
  4. Stopes are filled with paste
Show answer & solution

Answer: (A) Ore is blasted in rings from sublevels while the waste above caves in and ore is drawn with some dilution

Each ring is loaded from the drift brow until dilution is too high.

Question 13

Which orebodies are suited to sublevel caving?

  1. Narrow quartz veins
  2. Flat thin coal seams
  3. Placer gravels
  4. Steep, large orebodies with a hanging wall that caves
Show answer & solution

Answer: (D) Steep, large orebodies with a hanging wall that caves

Iron ore bodies such as Kiruna are classic examples.

Question 14

For which mining method is the Kiruna iron ore mine in Sweden famous?

  1. Sublevel caving
  2. Room and pillar
  3. Longwall
  4. Block caving
Show answer & solution

Answer: (A) Sublevel caving

Kiruna is one of the world's largest sublevel caving mines.

Question 15

Why is dilution high in sublevel caving?

  1. The ore is very soft
  2. There are no drawpoints
  3. Fill is drawn with the ore
  4. Ore is drawn in direct contact with caved waste
Show answer & solution

Answer: (D) Ore is drawn in direct contact with caved waste

Waste mixes with ore as the ring is drawn.

Question 16

What is draw control in caving mines?

  1. Control of explosive use
  2. Planned tonnage drawn from each drawpoint to control dilution and cave shape
  3. Control of ventilation fans
  4. Control of shaft hoisting speed
Show answer & solution

Answer: (B) Planned tonnage drawn from each drawpoint to control dilution and cave shape

Uneven draw leads to early dilution and stress problems.

Question 17

Why is fragmentation important in caving mines?

  1. It only affects surface crushing
  2. It has no effect
  3. Coarse fragmentation causes hang-ups and more secondary breaking
  4. Fine fragmentation always causes hang-ups
Show answer & solution

Answer: (C) Coarse fragmentation causes hang-ups and more secondary breaking

Fragmentation affects drawpoint productivity and draw control.

Question 18

What major hazard can occur if a large air gap forms above a cave?

  1. An air blast when the cave back suddenly collapses
  2. Flooding from the surface
  3. Spontaneous combustion of ore
  4. Methane outburst from coal
Show answer & solution

Answer: (A) An air blast when the cave back suddenly collapses

A sudden collapse compresses air and blasts it through the workings.

Question 19

What is a mud rush in caving mines?

  1. A dust explosion
  2. A sudden inflow of wet fine material into drawpoints
  3. A rock burst
  4. A slow inflow of clean water
Show answer & solution

Answer: (B) A sudden inflow of wet fine material into drawpoints

Mud rushes can bury equipment and kill workers.

Question 20

Which mine in Chile is one of the largest block caving operations in the world?

  1. Kiruna
  2. Saindak
  3. El Teniente
  4. Escondida open pit
Show answer & solution

Answer: (C) El Teniente

El Teniente has been block caved for decades.

Question 21

What is preconditioning in caving mines?

  1. Adding cement to the ore
  2. Drying the ore
  3. Painting drawpoints
  4. Hydraulic fracturing or blasting of the rock mass to improve caveability and fragmentation
Show answer & solution

Answer: (D) Hydraulic fracturing or blasting of the rock mass to improve caveability and fragmentation

Preconditioning helps strong rock cave and fragment finer.

Question 22

What is a grizzly in older caving and stoping operations?

  1. A type of bear-proof door
  2. A ventilation regulator
  3. A hoisting skip
  4. A screen of steel bars that stops oversize rock
Show answer & solution

Answer: (D) A screen of steel bars that stops oversize rock

Oversize on the grizzly is broken by hand or small charges.

Question 23

Which machine is most commonly used to load ore at drawpoints in modern caving mines?

  1. LHD
  2. Continuous miner
  3. Shearer
  4. Dragline
Show answer & solution

Answer: (A) LHD

LHDs carry ore to ore passes or trucks.

Question 24

Which two factors does Laubscher's caveability chart relate?

  1. Stripping ratio and price
  2. UCS and depth
  3. Mining rock mass rating (MRMR) and hydraulic radius
  4. RQD and grade
Show answer & solution

Answer: (C) Mining rock mass rating (MRMR) and hydraulic radius

The chart shows whether a given undercut will cave.

Question 25

What is an advance undercut in block caving?

  1. An undercut made after production
  2. An undercut blasted ahead of drawbell development to protect the extraction level from high stress
  3. A ventilation undercut
  4. A surface trench
Show answer & solution

Answer: (B) An undercut blasted ahead of drawbell development to protect the extraction level from high stress

The extraction level is then developed in de-stressed rock.

Question 26

What is the brow in a sublevel caving drift?

  1. The floor of the drift
  2. The shaft collar
  3. The edge of the drift roof at the ore ring where broken ore flows out
  4. A ventilation door
Show answer & solution

Answer: (C) The edge of the drift roof at the ore ring where broken ore flows out

Brow damage reduces recovery of the ring.

Question 27

What is top slicing?

  1. A modern block caving method
  2. A surface method
  3. A longwall method
  4. An old method where ore is mined in horizontal slices from the top downward under a mat of timber and caved waste
Show answer & solution

Answer: (D) An old method where ore is mined in horizontal slices from the top downward under a mat of timber and caved waste

Top slicing was used in weak ore before modern caving.

Question 28

What surface feature forms above a block cave?

  1. A waste dump
  2. A subsidence crater
  3. A haul ramp
  4. A tailings dam
Show answer & solution

Answer: (B) A subsidence crater

Caving propagates to the surface and forms a large depression.

Question 29

What is the cave back?

  1. The upper boundary of the caved zone
  2. The shaft bottom
  3. The floor of the extraction level
  4. The undercut level
Show answer & solution

Answer: (A) The upper boundary of the caved zone

The cave back moves upward as ore is drawn.

Question 30

Why must ore be drawn evenly in caving mines?

  1. To reduce hoisting speed
  2. To keep the cave advancing uniformly and avoid stress concentrations and early dilution
  3. To save explosives
  4. To use less ventilation
Show answer & solution

Answer: (B) To keep the cave advancing uniformly and avoid stress concentrations and early dilution

Uneven draw causes isolated draw and poor recovery.

Question 31

Which stress problem affects extraction level drifts in block caving?

  1. High abutment stress ahead of the undercut front
  2. No stress change
  3. Tensile stress only in the surface
  4. Very low stress everywhere
Show answer & solution

Answer: (A) High abutment stress ahead of the undercut front

Damage under the abutment zone requires heavy support.

Question 32

What is the draw column height in block caving?

  1. The height of a drawpoint
  2. The height of the undercut slot
  3. The height of the ore column above the extraction level
  4. The depth of the shaft
Show answer & solution

Answer: (C) The height of the ore column above the extraction level

Tall columns spread development cost over more tonnes.

Question 33

Why are caving methods unsuitable beneath important surface structures?

  1. They need no development
  2. They cause no ground movement
  3. They are too selective
  4. They cause large surface subsidence
Show answer & solution

Answer: (D) They cause large surface subsidence

Caving allows the overburden to collapse to the surface.

Question 34

Which underground mining method has the lowest cost per tonne?

  1. Shrinkage stoping
  2. Square set stoping
  3. Block caving
  4. Cut and fill stoping
Show answer & solution

Answer: (C) Block caving

Low development per tonne and no blasting of most ore keep costs down.

Question 35

What is the typical production rate of large block cave mines?

  1. About 1 tonne per hour
  2. Tens of thousands of tonnes per day
  3. About 100 tonnes per day
  4. A few tonnes per day
Show answer & solution

Answer: (B) Tens of thousands of tonnes per day

Large caves produce 50,000–150,000 t/d.

Question 36

What is the main difference between block caving and sublevel caving?

  1. There is no difference
  2. Sublevel caving is a surface method
  3. Block caving uses fill, sublevel caving does not
  4. In block caving the ore caves naturally, while in sublevel caving the ore is drilled and blasted ring by ring
Show answer & solution

Answer: (D) In block caving the ore caves naturally, while in sublevel caving the ore is drilled and blasted ring by ring

Only the undercut is blasted in block caving.

Question 37

What is the purpose of drawpoint spacing design in block caving?

  1. To ensure draw zones overlap so that ore is recovered without leaving pillars of ore
  2. To reduce ventilation
  3. To shorten the shaft
  4. To increase dilution
Show answer & solution

Answer: (A) To ensure draw zones overlap so that ore is recovered without leaving pillars of ore

Spacing too wide leaves ore and causes early dilution.

Practice these 37 questions interactively →