Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Underground Mining Methods: Longwall Mining

Mining Engineering · Underground Mining Methods

37 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is longwall mining?

  1. A surface strip method
  2. A method for steep veins
  3. A method that leaves regular pillars
  4. A method in which a long coal face is extracted in slices while the roof caves behind the supports
Show answer & solution

Answer: (D) A method in which a long coal face is extracted in slices while the roof caves behind the supports

Longwall gives high recovery and productivity in flat seams.

Question 2

Which machine cuts coal along a longwall face with rotating drums?

  1. Roadheader
  2. Coal plough
  3. Shearer
  4. Continuous miner
Show answer & solution

Answer: (C) Shearer

Double-ended ranging drum shearers are standard on modern faces.

Question 3

Which machine shaves thin slices of coal off the face by being pulled along it?

  1. Continuous miner
  2. Coal plough
  3. Drill jumbo
  4. Shearer
Show answer & solution

Answer: (B) Coal plough

Ploughs suit thin, soft seams.

Question 4

Which conveyor runs along a longwall face beneath the shearer?

  1. Armoured face conveyor (AFC)
  2. Belt conveyor
  3. Screw conveyor
  4. Bucket elevator
Show answer & solution

Answer: (A) Armoured face conveyor (AFC)

The AFC is a heavy chain conveyor that also guides the shearer.

Question 5

Which unit transfers coal from the face conveyor to the gate belt conveyor?

  1. Shuttle car
  2. Ore pass
  3. Beam stage loader
  4. Skip
Show answer & solution

Answer: (C) Beam stage loader

The stage loader often carries a crusher.

Question 6

Which gate road on a longwall usually carries the conveyor, power and intake air?

  1. Return airway only
  2. Maingate (headgate)
  3. Bleeder entry
  4. Tailgate
Show answer & solution

Answer: (B) Maingate (headgate)

The maingate is at the discharge end of the AFC.

Question 7

What is the gate road at the opposite end of the face from the maingate called?

  1. Tailgate
  2. Bord
  3. Maingate
  4. Crosscut
Show answer & solution

Answer: (A) Tailgate

The tailgate usually carries return air.

Question 8

What is retreat longwall mining?

  1. The face moves away from the main roads
  2. Pillars are left between rooms
  3. Overburden is cast into strips
  4. Gate roads are driven to the panel boundary first and the face is mined back towards the main roads
Show answer & solution

Answer: (D) Gate roads are driven to the panel boundary first and the face is mined back towards the main roads

Retreat avoids maintaining roads in the goaf.

Question 9

What is the main advantage of retreat longwall over advancing longwall?

  1. It needs no gate roads
  2. Gate roads are proved in advance and need not be maintained behind the face
  3. It has lower recovery
  4. It needs no supports
Show answer & solution

Answer: (B) Gate roads are proved in advance and need not be maintained behind the face

Faults and seam conditions are found before the face is set up.

Question 10

What is advancing longwall mining?

  1. Coal is mined by pillars
  2. Coal is mined from the surface
  3. Gate roads are driven first and the face retreats
  4. The face moves away from the main roads and gate roads are built behind the face along the goaf
Show answer & solution

Answer: (D) The face moves away from the main roads and gate roads are built behind the face along the goaf

Advancing gives early production but roadways in the goaf are hard to maintain.

Question 11

What is the typical length of a modern longwall face?

  1. 1 to 2 km
  2. 5 m
  3. 10 to 20 m
  4. 200 to 400 m
Show answer & solution

Answer: (D) 200 to 400 m

Longer faces improve productivity but need more equipment.

Question 12

What is the typical length of a modern longwall panel?

  1. 2 to 4 km
  2. 20 km
  3. 20 m
  4. 50 to 100 m
Show answer & solution

Answer: (A) 2 to 4 km

Long panels reduce the number of costly equipment moves.

Question 13

What is the typical recovery of coal within a longwall panel?

  1. Nearly 0%
  2. About 20%
  3. About 80% or more
  4. About 50% at most
Show answer & solution

Answer: (C) About 80% or more

Longwall leaves little coal except in chain and barrier pillars.

Question 14

What is the web of a shearer?

  1. The depth of cut taken by the drum in one pass
  2. The length of the face
  3. The height of the seam
  4. The width of the gate road
Show answer & solution

Answer: (A) The depth of cut taken by the drum in one pass

Webs are typically 0.8–1.0 m.

Question 15

What is bi-directional cutting on a longwall?

  1. The shearer cuts only one way
  2. The shearer cuts coal while travelling in both directions along the face
  3. Two shearers work side by side
  4. The face is cut from both gates at once
Show answer & solution

Answer: (B) The shearer cuts coal while travelling in both directions along the face

Bi-directional cutting increases output per shift.

Question 16

What happens to the face conveyor and shields after the shearer passes?

  1. They are removed from the face
  2. They are moved to the tailgate
  3. The conveyor is snaked forward and the shields advance to support the new roof
  4. They are lowered permanently
Show answer & solution

Answer: (C) The conveyor is snaked forward and the shields advance to support the new roof

Shields push the AFC and then pull themselves forward.

Question 17

What is longwall top coal caving (LTCC)?

  1. Caving the floor coal
  2. Mining only the top coal from the surface
  3. A thick-seam method in which top coal above the shields caves and is drawn onto a rear conveyor
  4. Mining with no shields
Show answer & solution

Answer: (C) A thick-seam method in which top coal above the shields caves and is drawn onto a rear conveyor

LTCC is widely used in thick seams in China and Australia.

Question 18

For which seam thickness is longwall top coal caving mainly used?

  1. Thick seams of more than about 4.5 to 5 m
  2. Seams of exactly 2 m
  3. Steep veins
  4. Thin seams of under 1 m
Show answer & solution

Answer: (A) Thick seams of more than about 4.5 to 5 m

The shearer cuts the lower section and the upper coal is caved.

Question 19

What is shortwall mining?

  1. A longwall over 1 km long
  2. A surface strip method
  3. A stoping method for veins
  4. A shorter face mined with a continuous miner under shield supports
Show answer & solution

Answer: (D) A shorter face mined with a continuous miner under shield supports

Shortwalls are used in small blocks of coal.

Question 20

Which hazards are most important in a longwall goaf?

  1. Explosive dust from cement
  2. Methane accumulation and spontaneous combustion
  3. Excessive daylight
  4. Flooding by seawater
Show answer & solution

Answer: (B) Methane accumulation and spontaneous combustion

Gas and oxidising coal in the goaf need careful ventilation and sealing.

Question 21

What is the face end on a longwall?

  1. The panel boundary
  2. The middle of the face
  3. The junction of the face with a gate road
  4. The shaft bottom
Show answer & solution

Answer: (C) The junction of the face with a gate road

Face ends need extra support because of high stress and large spans.

Question 22

What kind of seam is required for successful longwall mining?

  1. A very irregular vein
  2. A fairly regular flat seam without major faults
  3. A steep, faulted seam
  4. A thin, broken seam with many washouts
Show answer & solution

Answer: (B) A fairly regular flat seam without major faults

Faults and washouts stop the face and delay production.

Question 23

What is the main disadvantage of longwall mining?

  1. No need for ventilation
  2. Low recovery
  3. Low productivity
  4. High capital cost and inflexibility to geological disturbances
Show answer & solution

Answer: (D) High capital cost and inflexibility to geological disturbances

A full longwall set costs hundreds of millions of dollars.

Question 24

What is a longwall move?

  1. Relocation of all face equipment to a new panel
  2. Moving the shearer along the face
  3. Advancing the shields one web
  4. Turning the conveyor
Show answer & solution

Answer: (A) Relocation of all face equipment to a new panel

Moves take days to weeks and are planned carefully.

Question 25

In which non-coal deposits has longwall-type stoping been widely used?

  1. Deep, narrow tabular gold reefs of South Africa
  2. Kimberlite pipes
  3. Placer gravels
  4. Massive porphyry copper
Show answer & solution

Answer: (A) Deep, narrow tabular gold reefs of South Africa

Witwatersrand gold reefs are mined by scattered or longwall stoping.

Question 26

What is the yield load of a longwall shield?

  1. The weight of the shield
  2. The initial load applied when setting
  3. The load on the conveyor
  4. The load at which the leg relief valves open to protect the support
Show answer & solution

Answer: (D) The load at which the leg relief valves open to protect the support

Yielding prevents damage when the roof load becomes excessive.

Question 27

What is the setting load of a longwall shield?

  1. The load at which valves open
  2. The initial load applied by the legs to the roof when the support is set
  3. The shearer's cutting force
  4. The load carried by the AFC
Show answer & solution

Answer: (B) The initial load applied by the legs to the roof when the support is set

A good setting load limits early roof separation.

Question 28

Which longwall ventilation system brings intake air along one gate, across the face and out along the other gate, both connected to the same main roads?

  1. H-type ventilation
  2. Z-type ventilation
  3. U-type ventilation
  4. Y-type ventilation
Show answer & solution

Answer: (C) U-type ventilation

U-ventilation is the simplest and most common system.

Question 29

What is goaf flushing on a longwall?

  1. Washing coal at the surface
  2. Water spraying on the face
  3. Cleaning the conveyor
  4. Broken rock flowing from the goaf into the face area behind the shields
Show answer & solution

Answer: (D) Broken rock flowing from the goaf into the face area behind the shields

Flushing occurs when shields do not seal well against caved rock.

Question 30

Which machine is commonly used to drive longwall gate roads?

  1. Coal plough
  2. Shearer
  3. Continuous miner
  4. Dragline
Show answer & solution

Answer: (C) Continuous miner

Gate roads are developed by continuous miners or roadheaders.

Question 31

Which control system lets shields advance automatically following the shearer?

  1. Manual valve control
  2. Electro-hydraulic shield control
  3. Pneumatic remote control
  4. Rope haulage control
Show answer & solution

Answer: (B) Electro-hydraulic shield control

Automation improves cycle speed and consistency.

Question 32

What does panel width mean in longwall mining?

  1. The face length between the two gate roads
  2. The depth of the seam
  3. The web of the shearer
  4. The length of the panel along the gates
Show answer & solution

Answer: (A) The face length between the two gate roads

Panel width affects subsidence and pillar loads.

Question 33

What is a pre-driven recovery room in longwall mining?

  1. A refuge station
  2. The set-up room at the start
  3. A ventilation door
  4. An opening driven at the end of the panel to make shield removal easier
Show answer & solution

Answer: (D) An opening driven at the end of the panel to make shield removal easier

The face breaks into the recovery room and shields are pulled out.

Question 34

Which method gives the highest productivity in flat, regular underground coal seams?

  1. Shrinkage stoping
  2. Manual room and pillar
  3. Longwall with shearer
  4. Pick mining
Show answer & solution

Answer: (C) Longwall with shearer

Modern longwalls produce several million tonnes per year.

Question 35

What is the set-up entry in longwall mining?

  1. The room at the start of a panel where face equipment is installed
  2. The tailgate return
  3. The recovery room at the end
  4. The main shaft
Show answer & solution

Answer: (A) The room at the start of a panel where face equipment is installed

Equipment is assembled in the set-up room before mining starts.

Question 36

What is the main purpose of the shield canopy in longwall mining?

  1. To carry coal to the gate
  2. To cut coal
  3. To ventilate the goaf
  4. To support the roof over the face and protect workers and equipment
Show answer & solution

Answer: (D) To support the roof over the face and protect workers and equipment

The canopy carries roof load transferred through the hydraulic legs.

Question 37

Which gas drainage practice is used ahead of and behind gassy longwall faces?

  1. Sealing the maingate
  2. Methane drainage boreholes connected to a suction pipeline
  3. Increasing coal dust
  4. Spraying water on the face
Show answer & solution

Answer: (B) Methane drainage boreholes connected to a suction pipeline

Drained methane reduces gas levels and can be used for power.

Practice these 37 questions interactively →