What is a horizontal or nearly horizontal tunnel driven from the surface into a hillside to reach a deposit called?
Show answer & solution
Answer: (D) Adit
An adit gives access and drainage by gravity from hillside deposits.
Mining Engineering · Underground Mining Methods
39 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a horizontal or nearly horizontal tunnel driven from the surface into a hillside to reach a deposit called?
Answer: (D) Adit
An adit gives access and drainage by gravity from hillside deposits.
What is a vertical or steeply inclined opening from the surface that gives access to an underground mine called?
Answer: (B) Shaft
Shafts are used for hoisting, ventilation and access to deep mines.
What is an inclined opening from the surface that gives access to a seam, often fitted with a conveyor, called?
Answer: (C) Incline (slope)
Inclines are common for shallow coal seams.
What is a spiral or zig-zag inclined roadway that lets trucks and LHDs travel underground called?
Answer: (A) Decline (ramp)
Declines allow trackless equipment to drive from the surface to the workings.
What is a vertical or inclined opening driven upward from one level to another called?
Answer: (C) Raise
Raises are driven upward; winzes are sunk downward.
What is a vertical or inclined opening sunk downward from an underground level, not from the surface, called?
Answer: (B) Winze
A winze is a "blind shaft" sunk from within the mine.
What is a horizontal opening driven along the strike of an orebody called?
Answer: (A) Drift
Drifts follow the orebody along strike.
What is a horizontal opening driven across the strike of an orebody called?
Answer: (D) Crosscut
Crosscuts connect shafts or footwall drives with the orebody.
Which shaft sinking method freezes water-bearing ground with circulating brine before excavation?
Answer: (B) Ground freezing method
Freezing makes waterlogged sand and gravel strong and impermeable during sinking.
Which shaft sinking method injects cement or chemicals into water-bearing strata ahead of the sinking?
Answer: (A) Grouting (cementation)
Grout seals fissures and reduces water inflow.
Which machine excavates a raise by pulling a large reamer upward after a pilot hole has been drilled down?
Answer: (C) Raise borer
Raise boring gives smooth, safe raises without people in the raise.
Which raising method uses a climbing work platform that travels on a guide rail fixed to the raise wall?
Answer: (D) Alimak raise climber
The Alimak platform carries miners up to drill and charge the face.
What is drop raising?
Answer: (B) Forming a raise by blasting long holes drilled from the upper level in successive slices
Holes are drilled down from above and blasted upwards in lifts.
Which multi-boom machine drills blast holes in development headings?
Answer: (D) Drill jumbo
Hydraulic jumbos drill the full round quickly and accurately.
What is the pull (advance per round) in development blasting?
Answer: (C) Length of heading advanced by one blast
Good rounds pull 85–95% of the hole depth.
Which group of holes in a tunnel face creates the first opening for the rest of the round to break into?
Answer: (A) Cut holes
The cut is fired first to create free space.
Which cut uses parallel holes with one or more large empty holes as relief?
Answer: (D) Burn (parallel hole) cut
Parallel hole cuts suit long rounds and jumbo drilling.
Which cut uses pairs of angled holes meeting near the centre to form a wedge?
Answer: (A) V-cut (wedge cut)
The pull of a V-cut is limited by the width of the heading.
What are the holes along the bottom of a tunnel face called?
Answer: (C) Lifters
Lifters are fired last and heavily charged to lift the muck pile.
What are the holes along the sides of a tunnel face called?
Answer: (B) Wall (rib) holes
Wall holes trim the sides to the design profile.
Which holes are fired immediately after the cut to enlarge the opening?
Answer: (A) Easers (relievers)
Easers break rock towards the cut cavity.
Which machine excavates soft rock and coal roadways without blasting using a rotating cutter head on a boom?
Answer: (B) Roadheader
Roadheaders cut roadways to any shape in soft to medium rock.
What is a tunnel boring machine (TBM)?
Answer: (C) A machine that excavates the full circular face with rotating disc cutters
TBMs give smooth tunnels with little overbreak.
Why do mining regulations require at least two separate outlets from every underground mine?
Answer: (D) To provide an alternative escape route and allow ventilation
Two outlets allow escape if one is blocked and allow air to flow through the mine.
What is a shaft station (inset)?
Answer: (C) An enlarged excavation at a level where the shaft connects to that level
Stations hold loading and unloading equipment at each level.
What is the shaft sump?
Answer: (B) The extension of the shaft below the lowest level where water collects
Spillage and water collect in the sump and are pumped out.
What is the collar of a shaft?
Answer: (D) The top of the shaft at the surface
The collar is usually reinforced with a concrete ring.
What is a headframe?
Answer: (A) The structure over a shaft that carries the hoisting sheaves
Headframes are built of steel or concrete.
What is an ore pass?
Answer: (A) A steep opening through which broken ore flows by gravity to a lower level
Ore passes reduce the need for haulage between levels.
What is a level in an underground metal mine?
Answer: (B) Horizontal workings at one elevation from which stopes are developed and mined
Main levels are numbered by depth.
What is the vertical distance between main levels called?
Answer: (C) Level interval
Level intervals commonly range from 30 to 100 m.
What is development, as distinct from production, in underground mining?
Answer: (D) Openings driven to access and prepare the deposit before extraction
Development includes shafts, declines, drifts, crosscuts and raises.
What is a footwall drive?
Answer: (A) A drift in the footwall rock parallel to the orebody
Footwall drives give access to stopes along strike.
Why are main development openings often placed in the footwall?
Answer: (C) Footwall rock is less disturbed by mining of the orebody
In dipping orebodies, mining affects the hanging wall more than the footwall.
Which shaft lining is most commonly used in modern deep shafts?
Answer: (D) Concrete
Concrete linings are durable, fire-resistant and reduce air resistance.
Which shaft shape is most common in modern mines because of its strength and low air resistance?
Answer: (B) Circular
Circular shafts resist ground pressure well and carry concrete lining efficiently.
How are seams commonly accessed in hillside coal mines of Balochistan where coal outcrops on slopes?
Answer: (A) Inclined adits (slopes) driven down the seam from the outcrop
Most small coal mines in Balochistan use inclined drifts following the seam.
Which method of driving a heading uses drilling, charging, blasting, ventilating, mucking and supporting in a repeating cycle?
Answer: (B) Conventional drill and blast cycle
Each round advances the heading by the length of the pull.
What is a refuge chamber in an underground mine?
Answer: (D) A sealed station with air, water and communication where workers can shelter in an emergency
Refuge chambers protect workers who cannot escape after a fire or explosion.