Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.
Question 1
What is the main function of a traditional miner's dial?
- Measuring rock strength
- Measuring horizontal bearings of underground roadways using a magnetic needle
- Measuring air velocity
- Measuring methane concentration
Show answer & solution
Answer: (B) Measuring horizontal bearings of underground roadways using a magnetic needle
The miner's dial is a compass with sights, used for underground direction surveys.
Question 2
Why is a miner's dial unreliable near rails, steel supports and machinery?
- It cannot be levelled
- It needs bright light
- Its magnetic needle is affected by local attraction
- It is too heavy
Show answer & solution
Answer: (C) Its magnetic needle is affected by local attraction
Iron and steel deflect the needle and give wrong bearings.
Question 3
What additional measurement can a miner's dial fitted with a vertical arc make?
- Vertical angles (inclinations) of roadways
- Air velocity
- Gas content
- Rock hardness
Show answer & solution
Answer: (A) Vertical angles (inclinations) of roadways
The arc measures the slope of the line of sight.
Question 4
What is a hanging (suspension) compass?
- A gyroscope
- A laser instrument
- A compass fixed to a tripod
- A compass hung from a cord stretched between two points in a roadway to give its bearing
Show answer & solution
Answer: (D) A compass hung from a cord stretched between two points in a roadway to give its bearing
It is used in narrow, steep workings where a tripod is impractical.
Question 5
Which instrument is hung on a cord to measure the inclination of a roadway or seam?
- Gyro-theodolite
- Hanging compass
- Dumpy level
- Hanging clinometer
Show answer & solution
Answer: (D) Hanging clinometer
The clinometer arc reads the slope of the cord.
Question 6
What is a gyro-theodolite?
- A theodolite with a magnetic compass
- A theodolite with a gyroscope attachment that finds true north independently of magnetism
- A laser plummet
- A digital level
Show answer & solution
Answer: (B) A theodolite with a gyroscope attachment that finds true north independently of magnetism
Gyro-theodolites are used for orienting underground surveys.
Question 7
On what principle does a gyro-theodolite find true north?
- A spinning gyroscope aligns its axis with the meridian under the earth's rotation
- Gravity points to the north pole
- Light is reflected from the sun
- The needle points to magnetic north
Show answer & solution
Answer: (A) A spinning gyroscope aligns its axis with the meridian under the earth's rotation
The gyroscope oscillates about the meridian, which is found from the oscillations.
Question 8
Where do gyro-theodolites lose accuracy?
- In dark roadways
- Near the equator
- Near the earth's poles
- In deep mines
Show answer & solution
Answer: (C) Near the earth's poles
The horizontal component of the earth's rotation decreases towards the poles.
Question 9
Why are underground survey stations usually fixed in the roof?
- Lights are fitted in the roof
- The roof is softer
- It saves time in all cases
- The floor is disturbed by traffic, water and floor heave
Show answer & solution
Answer: (D) The floor is disturbed by traffic, water and floor heave
Plumb bobs or optical plummets are hung from roof stations.
Question 10
What is the three-tripod system of traversing?
- Using three theodolites at once
- Instrument and targets are interchanged on tripods so that centring errors are reduced
- Using three chains
- Measuring three angles at each station
Show answer & solution
Answer: (B) Instrument and targets are interchanged on tripods so that centring errors are reduced
Forced centring keeps the same points between setups.
Question 11
How is the direction of a heading usually controlled during driving?
- By the miner's judgement only
- By the ventilation fan
- By a laser beam or line set out by the surveyor on the centre line
- By the conveyor
Show answer & solution
Answer: (C) By a laser beam or line set out by the surveyor on the centre line
The drillers align their holes with the line.
Question 12
What is meant by giving line and grade in mine surveying?
- Marking the direction and gradient that a heading must follow
- Marking blast holes
- Giving the miners their wages
- Setting out ventilation doors
Show answer & solution
Answer: (A) Marking the direction and gradient that a heading must follow
Line pins and grade marks guide the driving of roadways.
Question 13
- A ventilation survey
- A survey of drill holes only
- A survey to make sure that two headings driven towards each other meet correctly
- A survey of old workings
Show answer & solution
Answer: (C) A survey to make sure that two headings driven towards each other meet correctly
Holing surveys must control both line and level errors.
Question 14
Which error is most critical in a holing survey between two headings?
- Lateral (side) error at the meeting point
- Error in chainage of a single station
- Error in the date
- Error in staff reading only
Show answer & solution
Answer: (A) Lateral (side) error at the meeting point
Bearing errors grow with distance and cause lateral misses.
Question 15
Which instrument directly measures the dip of a seam underground?
- Planimeter
- Clinometer
- Anemometer
- Hygrometer
Show answer & solution
Answer: (B) Clinometer
Dip is the maximum inclination of the bed to the horizontal.
Question 16
How does apparent dip compare with true dip?
- Apparent dip is always zero
- Apparent dip is always greater
- They are always equal
- Apparent dip is less than or equal to true dip
Show answer & solution
Answer: (D) Apparent dip is less than or equal to true dip
True dip is measured at right angles to strike.
Question 17
Why must old workings be accurately surveyed and shown on mine plans?
- To calculate wages
- To measure air velocity
- To prevent dangerous approach to waterlogged or gassy old workings
- To decorate the plan
Show answer & solution
Answer: (C) To prevent dangerous approach to waterlogged or gassy old workings
Many inrush disasters resulted from inaccurate plans of old workings.
Question 18
What precaution is required when approaching old waterlogged workings?
- Drilling advance boreholes ahead of the face
- Removing all supports
- Switching off the pumps
- Increasing the blasting charge
Show answer & solution
Answer: (A) Drilling advance boreholes ahead of the face
Advance and flank boreholes detect water before the face breaks through.
Question 19
How are surface subsidence movements usually monitored?
- By a chain survey once only
- By a hand lens
- By a magnetic compass
- By repeated levelling and coordinate surveys of monitoring points
Show answer & solution
Answer: (D) By repeated levelling and coordinate surveys of monitoring points
Lines of survey pegs over the panel are measured at intervals.
Question 20
Which instrument measures closure (convergence) between the roof and floor or the sidewalls of a roadway?
- Abney level
- Tape extensometer (convergence meter)
- Planimeter
- Dumpy level
Show answer & solution
Answer: (B) Tape extensometer (convergence meter)
Repeated readings between fixed studs show convergence.
Question 21
How are the details of an underground roadway surveyed?
- By aerial photography
- By chaining on the surface
- By compass only
- By measuring offsets from the traverse line
Show answer & solution
Answer: (D) By measuring offsets from the traverse line
Offsets locate walls, junctions and equipment.
Question 22
Why must bearings from a miner's dial be corrected periodically?
- Magnetic declination changes with time
- The roadway moves
- The dial is too heavy
- The dial needle gets longer
Show answer & solution
Answer: (A) Magnetic declination changes with time
Annual and secular changes in declination must be applied.
Question 23
Why should an underground traverse be closed or run twice?
- To double the length
- To detect and control errors
- To use more instruments
- To reduce lighting needs
Show answer & solution
Answer: (B) To detect and control errors
An unchecked open traverse can contain undetected blunders.
Question 24
Which instrument now measures most underground distances precisely?
- Gunter's chain
- Plane table
- Total station with EDM
- Ranging rod
Show answer & solution
Answer: (C) Total station with EDM
Reflectorless and prism EDMs work well in roadways.
Question 25
Which instrument surveys inaccessible stope voids remotely?
- Cavity monitoring system (laser scanner)
- Plane table
- Abney level
- Miner's dial
Show answer & solution
Answer: (A) Cavity monitoring system (laser scanner)
The scanner is pushed into the void on a boom to map its shape.
Question 26
What does the strike of a bed mean?
- The maximum slope of the bed
- The age of the bed
- The thickness of the bed
- The direction of a horizontal line on the bedding plane
Show answer & solution
Answer: (D) The direction of a horizontal line on the bedding plane
Strike is at right angles to the direction of true dip.
Question 27
Why are illuminated targets or lamps used for sighting underground?
- To warm the instrument
- To dry the air
- Underground workings are dark
- To mark explosives
Show answer & solution
Answer: (C) Underground workings are dark
Lamps or lit targets are placed at the stations being sighted.
Question 28
What is the main difficulty of surveying in steep inclines with a theodolite?
- Distances cannot be measured
- Very steep sights need a diagonal eyepiece or auxiliary telescope
- No light is available
- The instrument cannot be centred
Show answer & solution
Answer: (B) Very steep sights need a diagonal eyepiece or auxiliary telescope
Ordinary eyepieces cannot be viewed at steep angles.
Question 29
What is the dip direction of a seam?
- The direction of the shaft
- The thickness of the seam
- The compass direction towards which the seam slopes downward most steeply
- The direction of a horizontal line on the seam
Show answer & solution
Answer: (C) The compass direction towards which the seam slopes downward most steeply
Dip direction is at 90° to strike.
Question 30
Which survey method is used to locate the position of a borehole bottom that may have deviated?
- Plane table survey
- Compass survey from the collar
- Borehole deviation survey with downhole instruments
- Chain survey on the surface
Show answer & solution
Answer: (C) Borehole deviation survey with downhole instruments
Gyro or magnetic probes measure the hole path at intervals.
Question 31
Why should survey instruments be allowed to adjust to underground temperature before use?
- To level the bubble automatically
- To charge the batteries
- To clean the lenses
- To avoid errors from temperature changes and condensation on optics
Show answer & solution
Answer: (D) To avoid errors from temperature changes and condensation on optics
Fogged optics and thermal expansion reduce accuracy.
Question 32
What is a stope survey used for?
- Measuring explosive stock
- Measuring the volume and shape of ore extracted for reconciliation and planning
- Measuring ventilation only
- Measuring wages
Show answer & solution
Answer: (B) Measuring the volume and shape of ore extracted for reconciliation and planning
Stope surveys compare mined tonnage with planned tonnage.
Question 33
Which reference is used to calculate the volume of ore mined from a stope between two survey dates?
- Difference between the surveyed void shapes at the two dates
- The explosives used only
- The wages paid
- The number of trucks only
Show answer & solution
Answer: (A) Difference between the surveyed void shapes at the two dates
Survey volumes multiplied by density give mined tonnes.
Question 34
What is a station mark in underground surveying usually made of?
- A painted circle on the floor
- A chalk mark on the wall
- A wooden peg in the floor only
- A metal spad or plug fixed into the roof or a drilled hole
Show answer & solution
Answer: (D) A metal spad or plug fixed into the roof or a drilled hole
Spads in the roof allow plumb bobs to be hung for centring.