What is levelling?
Show answer & solution
Answer: (B) The process of determining the relative heights of points
Levelling gives reduced levels above a datum.
Mining Engineering · Mine Surveying
35 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is levelling?
Answer: (B) The process of determining the relative heights of points
Levelling gives reduced levels above a datum.
What is a datum in levelling?
Answer: (D) A reference surface from which heights are measured, often mean sea level
All reduced levels are referred to the datum.
To which datum are heights in Pakistan's national levelling network referred?
Answer: (C) Mean sea level at Karachi
Heights above mean sea level are based on the Karachi tide gauge datum.
What is a benchmark?
Answer: (A) A fixed point of known reduced level
Benchmarks are used to start and close levelling lines.
What is a temporary benchmark (TBM)?
Answer: (B) A point of known level set up for a particular survey
TBMs are used near the work site, such as at a pit or shaft.
What is a backsight in levelling?
Answer: (D) The first staff reading taken after setting up the level, on a point of known level
The backsight gives the height of instrument.
What is a foresight in levelling?
Answer: (C) The last staff reading taken before moving the level
The foresight point usually becomes a change point.
What is an intermediate sight?
Answer: (A) A staff reading between the backsight and the foresight at the same setup
Intermediate sights give levels of detail points.
What is a change point in levelling?
Answer: (B) A point on which both a foresight and a backsight are taken
Change points transfer level from one setup to the next.
How is reduced level found in the height of instrument method?
Answer: (D) RL = height of instrument − staff reading
HI = RL of the backsight point + backsight.
Which arithmetic check applies to the rise and fall method?
Answer: (C) ΣBS − ΣFS = ΣRise − ΣFall = Last RL − First RL
This check confirms the reduction is correct.
Which method of reducing levels also provides a check on intermediate sights?
Answer: (A) Rise and fall method
In the HI method, errors in intermediate RLs are not detected.
If a backsight of 1.500 m is taken on a benchmark of RL 100.000 m and a foresight of 2.300 m on point A, what is the RL of A?
Answer: (B) 99.200 m
HI = 101.500; RL of A = 101.500 − 2.300 = 99.200 m.
What is the main feature of a dumpy level?
Answer: (D) The telescope is rigidly fixed to the vertical spindle
The dumpy level is simple and stable.
What does an automatic level use to keep the line of sight horizontal?
Answer: (B) An optical-mechanical compensator
Once roughly levelled, the compensator sets the line of sight automatically.
Which of these is a temporary adjustment of a level?
Answer: (C) Elimination of parallax
Temporary adjustments are setting up, levelling up and removing parallax.
What is parallax in a levelling telescope?
Answer: (A) Apparent movement of the image against the cross hairs because they are not in the same plane
Parallax is removed by focusing the eyepiece and then the objective.
What is reciprocal levelling used for?
Answer: (D) Levelling across a river or valley where equal sight lengths are impossible
It eliminates collimation, curvature and refraction errors.
What is the combined correction for curvature and refraction in metres, for a distance d in kilometres?
Answer: (B) 0.0673d²
Curvature alone is 0.0785d²; refraction reduces it by about one-seventh.
What is the correction for the earth's curvature alone, in metres, for a distance d in kilometres?
Answer: (C) 0.0785d²
The curvature correction is subtractive from staff readings.
How is collimation error in levelling eliminated?
Answer: (D) By keeping backsight and foresight distances equal
Equal sight lengths make the error equal on both readings.
What is profile (longitudinal) levelling?
Answer: (A) Levelling along a line, such as a roadway or haul road, to draw its longitudinal section
Profiles are used to design gradients.
What is cross-sectioning in levelling?
Answer: (D) Taking levels at right angles to a centre line at intervals
Cross-sections are used for earthwork volumes.
What is fly levelling?
Answer: (C) Rapid levelling to check or carry a level approximately between distant points
Fly levelling uses long sights and few intermediate readings.
What is trigonometric levelling?
Answer: (A) Finding heights from measured vertical angles and distances
Total stations perform trigonometric levelling automatically.
What is the Abney level mainly used for?
Answer: (B) Measuring slopes and gradients quickly
The Abney level is a hand-held clinometer with a sighting tube.
How are levels taken to points on the roof of an underground roadway?
Answer: (C) The staff is held inverted on the point and the reading is treated as negative
Inverted staff readings are entered with a minus sign.
What percentage gradient is equal to a gradient of 1 in 50?
Answer: (B) 2%
1/50 = 0.02 = 2%.
What is the gradient of a roadway that rises 5 m over a horizontal distance of 250 m?
Answer: (C) 1 in 50
250/5 = 50.
How does the radius of curvature of a bubble tube affect its sensitivity?
Answer: (D) A larger radius makes the bubble more sensitive
A larger radius gives more bubble movement per unit tilt.
What is the closing error in a levelling line?
Answer: (A) The difference between the computed and the known reduced level of the closing benchmark
It shows the accuracy of the levelling.
How is the closing error usually distributed in levelling?
Answer: (D) In proportion to the distance or number of setups from the start
Points further along the line receive larger corrections.
What type of staff is read automatically by a digital level?
Answer: (A) A bar-coded staff
The digital level reads the code electronically.
On what principle is the water tube (hydrostatic) level based?
Answer: (B) Water in a connected tube stands at the same level at both ends
Hydrostatic levelling is useful for short distances underground.
What is the height of instrument in levelling?
Answer: (B) The reduced level of the line of sight of the instrument
HI is constant for all readings from one setup.