Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Mine Surveying: Shaft Correlation

Mining Engineering · Mine Surveying

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is correlation (orientation) surveying in mines?

  1. Measuring rock strength
  2. Ventilation surveying
  3. Measuring ore grade
  4. Transferring the surface bearing and coordinates underground so that both surveys use the same system
Show answer & solution

Answer: (D) Transferring the surface bearing and coordinates underground so that both surveys use the same system

Correlation ties underground plans to the surface grid.

Question 2

Which methods are used to correlate surface and underground surveys through shafts?

  1. Levelling only
  2. Compass only
  3. Two wires in one shaft, one wire in each of two shafts, or gyro-theodolite
  4. Chain and offset only
Show answer & solution

Answer: (C) Two wires in one shaft, one wire in each of two shafts, or gyro-theodolite

The choice depends on the number of shafts and accuracy required.

Question 3

Where is the theodolite placed in the Weisbach triangle method of shaft correlation?

  1. Exactly midway between the wires
  2. Nearly in line with the two shaft wires, slightly off the line
  3. At the shaft bottom only
  4. Far away at right angles to the wires
Show answer & solution

Answer: (B) Nearly in line with the two shaft wires, slightly off the line

A very small angle at the instrument keeps errors small.

Question 4

Why is the angle at the instrument kept very small in the Weisbach triangle?

  1. To reduce the error in calculating the bearing of the wire plane
  2. To make the triangle large
  3. To speed up hoisting
  4. To avoid using a theodolite
Show answer & solution

Answer: (A) To reduce the error in calculating the bearing of the wire plane

The triangle is very thin, so small angle errors have little effect.

Question 5

Which correlation method uses an instrument station that forms a quadrilateral with the two shaft wires?

  1. Weisbach triangle method
  2. Gyro method
  3. Weiss quadrilateral method
  4. Magnetic method
Show answer & solution

Answer: (C) Weiss quadrilateral method

It is used when the instrument cannot be placed nearly in line with the wires.

Question 6

Why are plumb bobs immersed in oil or water during shaft plumbing?

  1. To prevent corrosion only
  2. To clean the bobs
  3. To make the bobs heavier
  4. To damp the oscillations of the wires
Show answer & solution

Answer: (D) To damp the oscillations of the wires

Damping lets the wires settle in their mean position.

Question 7

Which type of wire is used for plumbing shafts?

  1. Copper wire
  2. High-tensile steel (piano) wire
  3. Cotton cord
  4. Plastic rope
Show answer & solution

Answer: (B) High-tensile steel (piano) wire

Strong, thin wire carries heavy bobs with little stretch.

Question 8

What is the main source of error in shaft wire plumbing?

  1. Air currents deflecting the wires
  2. Gravity
  3. Light
  4. Temperature of the bobs only
Show answer & solution

Answer: (A) Air currents deflecting the wires

Ventilation is often reduced or stopped during plumbing.

Question 9

Why is the two-shaft method of correlation more accurate than two wires in one shaft?

  1. It uses no instruments
  2. It uses lighter bobs
  3. The wires are much farther apart, so a small displacement causes a smaller bearing error
  4. It needs no surface survey
Show answer & solution

Answer: (C) The wires are much farther apart, so a small displacement causes a smaller bearing error

Short wire bases in one shaft magnify displacement errors.

Question 10

What is the main advantage of gyro orientation over wire correlation?

  1. It is unaffected by latitude
  2. It gives heights
  3. It needs no instrument
  4. It determines the azimuth underground directly without plumbing wires in the shaft
Show answer & solution

Answer: (D) It determines the azimuth underground directly without plumbing wires in the shaft

Gyro orientation is quick and needs no interruption of hoisting.

Question 11

How are levels usually transferred down a shaft?

  1. By a measured long steel tape or by EDM down the shaft
  2. By a planimeter
  3. By a dumpy level only
  4. By a magnetic compass
Show answer & solution

Answer: (A) By a measured long steel tape or by EDM down the shaft

The depth is added to the surface level of the collar.

Question 12

Which correction is needed when a long steel tape is hung freely down a shaft?

  1. Slope correction only
  2. Elongation due to the tape's own weight and the tension applied
  3. Curvature correction only
  4. Sag correction for horizontal tapes
Show answer & solution

Answer: (B) Elongation due to the tape's own weight and the tension applied

The tape stretches under its weight and the attached load.

Question 13

Why is correlation of surface and underground surveys important?

  1. To check ventilation
  2. To calculate wages
  3. So that underground workings can be related accurately to surface features, boundaries and other workings
  4. To decorate the mine plan
Show answer & solution

Answer: (C) So that underground workings can be related accurately to surface features, boundaries and other workings

Correct correlation prevents trespass beyond boundaries and inrushes.

Question 14

How is the mean position of a swinging plumb wire found?

  1. By observing its extreme positions and taking the average
  2. By using a compass
  3. By stopping it by hand
  4. By reading it once only
Show answer & solution

Answer: (A) By observing its extreme positions and taking the average

Observations of the swing give the rest position.

Question 15

What is coplaning in shaft correlation?

  1. Placing the wires in two shafts
  2. Plumbing a single wire
  3. Levelling the shaft collar
  4. Setting the instrument's line of sight exactly in the plane of the two shaft wires
Show answer & solution

Answer: (D) Setting the instrument's line of sight exactly in the plane of the two shaft wires

Coplaning is used on the surface and underground to transfer the wire bearing.

Question 16

How many wires are hung in a shaft for the one-shaft correlation method?

  1. Four
  2. Two
  3. One
  4. Ten
Show answer & solution

Answer: (B) Two

The two wires define a plane whose bearing is transferred underground.

Question 17

Why is the ventilation in a shaft often reduced during shaft plumbing?

  1. To reduce air currents that deflect the wires
  2. To keep the bobs warm
  3. To speed up hoisting
  4. To save power
Show answer & solution

Answer: (A) To reduce air currents that deflect the wires

Strong air currents can displace wires by several millimetres.

Question 18

How is the verticality of a shaft checked?

  1. With a magnetic compass
  2. With a planimeter
  3. With plumb lines or laser plumbing at intervals down the shaft
  4. With a dumpy level only
Show answer & solution

Answer: (C) With plumb lines or laser plumbing at intervals down the shaft

Offsets from the plumb lines to the shaft walls are measured.

Question 19

Why is magnetic correlation rarely used in modern mines?

  1. It needs two shafts
  2. Steelwork in and near the shaft disturbs the magnetic needle
  3. It gives heights only
  4. Compasses are too expensive
Show answer & solution

Answer: (B) Steelwork in and near the shaft disturbs the magnetic needle

Local attraction makes magnetic orientation unreliable underground.

Question 20

What is an azimuth in surveying?

  1. The depth of a shaft
  2. The angle of a slope
  3. The vertical angle of a line
  4. The horizontal angle of a line measured clockwise from true north
Show answer & solution

Answer: (D) The horizontal angle of a line measured clockwise from true north

Gyro-theodolites give the azimuth of a line.

Question 21

What is grid convergence?

  1. The angle between two shafts
  2. The angle between grid north and true north at a point
  3. The angle of a slope
  4. The difference between two benchmarks
Show answer & solution

Answer: (B) The angle between grid north and true north at a point

Gyro (true) azimuths are converted to grid bearings using convergence.

Question 22

How does increasing shaft depth affect wire plumbing?

  1. It increases oscillation and air deflection, reducing accuracy
  2. It removes the need for bobs
  3. It has no effect
  4. It improves accuracy
Show answer & solution

Answer: (A) It increases oscillation and air deflection, reducing accuracy

Deep shafts make gyro orientation more attractive.

Question 23

Which trigonometric relation is used to solve the Weisbach triangle?

  1. Simpson's rule
  2. The cosine of zero
  3. Pythagoras' theorem only
  4. The sine rule
Show answer & solution

Answer: (D) The sine rule

The small angle at the wire is found from the sine rule.

Question 24

Which instrument projects a vertical laser line for shaft alignment and plumbing?

  1. Miner's dial
  2. Dumpy level
  3. Laser plummet (zenith or nadir plummet)
  4. Abney level
Show answer & solution

Answer: (C) Laser plummet (zenith or nadir plummet)

Laser plumbing is used for shaft sinking and installing guides.

Question 25

What is transferred underground besides bearing during a shaft correlation survey?

  1. Ore grade
  2. Rock strength
  3. Air quality
  4. Coordinates (position) of the shaft wires
Show answer & solution

Answer: (D) Coordinates (position) of the shaft wires

Both direction and position are needed for the underground traverse.

Question 26

What is the purpose of placing reference marks at the shaft collar and at underground shaft stations?

  1. To provide fixed points for transferring coordinates and levels down the shaft
  2. To mark wages
  3. To mark ventilation doors
  4. To store explosives
Show answer & solution

Answer: (A) To provide fixed points for transferring coordinates and levels down the shaft

Reference marks allow repeated checks of the shaft survey.

Question 27

Why should correlation surveys be repeated at intervals in a working mine?

  1. Because the shaft moves daily
  2. To check the accuracy of underground orientation as the mine expands
  3. To train winding enginemen
  4. To use more wire
Show answer & solution

Answer: (B) To check the accuracy of underground orientation as the mine expands

Repeated or independent checks guard against blunders.

Question 28

What is the effect of a 1 mm error in the position of one of two wires 3 m apart on the bearing of the wire plane?

  1. About 10 degrees
  2. About 1 degree
  3. About 1 minute of arc
  4. No effect
Show answer & solution

Answer: (C) About 1 minute of arc

Angle ≈ 1/3000 radian ≈ 1.15 minutes, which grows into large errors in long traverses.

Question 29

How does a long underground traverse amplify a small orientation error from shaft correlation?

  1. The error becomes vertical only
  2. Lateral error grows in proportion to the distance from the shaft
  3. The error disappears with distance
  4. The error stays fixed in millimetres
Show answer & solution

Answer: (B) Lateral error grows in proportion to the distance from the shaft

An error of 1 minute gives about 0.3 m offset per kilometre.

Question 30

Which gyro observation method determines north by timing the oscillation of the gyro mark about a scale zero?

  1. Reversal points method only
  2. Coplaning method
  3. Transit (timing) method
  4. Weisbach method
Show answer & solution

Answer: (C) Transit (timing) method

Both transit and reversal-point methods are used with gyro-theodolites.

Practice these 30 questions interactively →