What is plane surveying?
Show answer & solution
Answer: (D) Surveying in which the curvature of the earth is ignored
Plane surveying is used for areas up to about 250 km², including most mines.
Mining Engineering · Mine Surveying
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is plane surveying?
Answer: (D) Surveying in which the curvature of the earth is ignored
Plane surveying is used for areas up to about 250 km², including most mines.
What is geodetic surveying?
Answer: (B) Surveying of large areas in which the earth's curvature is taken into account
Geodetic surveys provide the national control framework.
Why is the principle of "working from the whole to the part" followed in surveying?
Answer: (C) To prevent the accumulation of errors
A strong main framework is set up first and details are fitted within it.
On what principle is chain surveying based?
Answer: (A) Triangulation using a network of well-conditioned triangles
Chain surveying measures only lengths of triangle sides.
What is a well-conditioned triangle in chain surveying?
Answer: (C) A triangle with no angle smaller than about 30° or larger than about 120°
Very acute or obtuse angles magnify plotting errors.
What is the length of a Gunter's chain?
Answer: (C) 66 feet (about 20.12 m)
The Gunter's chain has 100 links of 0.66 ft each.
Which lengths are common for metric surveying chains?
Answer: (C) 20 m and 30 m
Metric chains have tallies at every 5 m and brass rings at every metre.
What is ranging in chain surveying?
Answer: (B) Establishing intermediate points on a straight line between two stations
Ranging rods are lined up by eye or with an instrument.
What is an offset in chain surveying?
Answer: (A) A lateral measurement from the chain line to a detail
Offsets are usually taken at right angles to the chain line.
Which type of error always occurs in the same direction and accumulates with the number of measurements?
Answer: (D) Systematic (cumulative) error
Wrong tape length is a typical systematic error.
Which type of error is equally likely to be positive or negative and tends to cancel out?
Answer: (B) Random (compensating) error
Random errors follow the laws of probability.
What is the correction to reduce a length L measured along a slope of angle θ to its horizontal equivalent?
Answer: (A) Subtract L(1 − cos θ)
The horizontal distance is L cos θ, which is shorter than the slope length.
Which formula gives the temperature correction for a steel tape of length L and expansion coefficient α?
Answer: (D) αL(Tm − T0)
Tm is the mean field temperature and T0 the standard temperature.
What is a whole circle bearing?
Answer: (A) The horizontal angle of a line measured clockwise from north, from 0° to 360°
WCB is also called azimuth.
What is a quadrantal (reduced) bearing?
Answer: (B) The angle of a line measured from north or south towards east or west, from 0° to 90°
Example: N 45° E or S 30° W.
What is the quadrantal bearing of a line with a whole circle bearing of 210°?
Answer: (D) S 30° W
210° − 180° = 30°, measured from south towards west.
What is the back bearing of a line whose whole circle bearing is 60°?
Answer: (C) 240°
Back bearing = fore bearing ± 180°.
What is magnetic declination?
Answer: (D) The horizontal angle between true north and magnetic north
Declination varies with place and time.
What is local attraction in compass surveying?
Answer: (A) Deviation of the magnetic needle caused by nearby iron or magnetic materials
Rails, pipes and steel supports cause local attraction.
How is local attraction detected in a compass traverse?
Answer: (B) Fore and back bearings of a line do not differ by exactly 180°
A station free from local attraction is used to correct the others.
Which bearing system does the prismatic compass read?
Answer: (A) Whole circle bearings
The surveyor's compass reads quadrantal bearings.
What is magnetic dip?
Answer: (D) The inclination of a freely suspended magnetic needle to the horizontal
A rider weight on the needle balances dip.
What are isogonic lines?
Answer: (C) Lines joining places of equal magnetic declination
Agonic lines join places of zero declination.
What is a total station?
Answer: (B) An electronic theodolite combined with an electronic distance meter
It measures angles and distances and stores coordinates.
On what principle do most electronic distance meters (EDMs) measure distance?
Answer: (A) Phase comparison of a modulated electromagnetic wave sent to a reflector and back
Pulse (time-of-flight) EDMs are also used.
What is the minimum number of satellites needed for a three-dimensional GNSS (GPS) position fix?
Answer: (C) 4
Four satellites solve for X, Y, Z and receiver clock error.
What does RTK GNSS surveying provide?
Answer: (B) Centimetre-level positions in real time using corrections from a base station
RTK is widely used for open pit and dump surveys.
What does a map scale with representative fraction 1:1000 mean?
Answer: (D) One unit on the map represents 1,000 of the same units on the ground
At 1:1000, 1 mm on the plan equals 1 m on the ground.
What is the main advantage of plane table surveying?
Answer: (C) Plotting is done in the field at the same time as observation
Mistakes are seen and corrected on site.
How is the least count of a vernier determined?
Answer: (B) Value of one main scale division divided by the number of vernier divisions
Least count is the smallest reading the vernier can give.
Which method is now widely used for rapid volume surveys of stockpiles, dumps and pits?
Answer: (D) Drone (UAV) photogrammetry and laser scanning
Drones capture millions of points quickly and safely.
How does local attraction at a station affect the included angles measured at that station?
Answer: (A) Included angles are not affected because all bearings are shifted equally
Local attraction adds the same error to every bearing from that station.
How many square metres are there in one hectare?
Answer: (C) 10,000
One hectare is 100 m × 100 m.
What is the national mapping organisation of Pakistan responsible for topographic maps and the geodetic network?
Answer: (A) Survey of Pakistan
Survey of Pakistan, headquartered in Rawalpindi, maintains national control and maps.
What is the purpose of reconnaissance before a survey?
Answer: (D) To inspect the area and plan station positions and methods
A good reconnaissance saves time and avoids weak survey layouts.
What is a survey station?
Answer: (B) A fixed point from which survey observations are made
Stations are marked by pegs, nails or monuments.